(Q6) A solid spring steel shaft in small engine with 5hp at 3000rpm is used as a torque measuring device at the rated load. Select a suitable length and diameter combination for this measurement assuming an angular deflection of 10•. The modulus of elastic of the spring steel 28.6×106 psi and the Poisson's ratio is 0.3.

(Q6) A solid spring steel shaft in small engine with 5hp at 3000rpm is used as a torque measuring device at the rated load. Select a suitable length and diameter combination for this measurement assuming an angular deflection of 10•. The modulus of elastic of the spring steel 28.6×106 psi and the Poisson's ratio is 0.3.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.8.8P: A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque...

See similar textbooks

Similar questions

A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque 150N·n/m. The bar has diameter d = 30 mm. Calculate the reactive torques at the supports and the angle of twist at midspan. Assume that G = 28 GPa.
A solid copper bar of circular cross section has length L = 1.25 m and shear modulus of elasticity G = 45 GPa. The bar is designed to carry a 250 N · m torque acting at the ends. If the allowable shear stress is 30 M Pa and the allowable angle of twist between the ends is 2.5°, what is the minimum required diameter?
A scuba t a n k (see fig ure) i s bci ng d e signed fo r an internal pressure of 2640 psi with a factor of safety of 2,0 with respect to yielding. The yield stress of the steel is 65,000 psi in tension and 32,000 psi in shear, (a) If the diameter of the tank is 7,0 in., what is the minimum required wall thickness? (b) If the wall thickness is 0.25 in., what is the maximum acceptable internal pressure?
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
Repeat Problem 2.3-18, but assume that the bar is made of copper alloy. Calculate the displacements SBand Scif P = 50 kips, L = 5 ft = 3/5 in., b1= 2.75 in., b2= 3 in., and E = 16,000 ksi.
A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
A circular tube AB is fixed at one end and free at the other. The tube is subjected to concentrated torques as shown in the figure. If the outer radius of the tube is 1.5 in, and the thickness is 3/4 in., calculate the strain energy stored in the tube. Let G= 11,800 ksi.
A solid circular bar A BCD with fixed supports at ends A and D is acted upon by two equal and oppositely directed torques T0, as shown in the figure. The torques arc applied at points B and C each of which is located at distance x from one end of the bar. (The distance x may vary from zero to L/2.) For what distance x will the angle of twist at points B and C be a maximum? What is the corresponding angle of twist 0max?
Two sections of steel drill pipe, joined by bolted flange plates at B, arc subjected to a concentrated torque 4000 kip-in. at x = 3 ft, and a uniformly distributed torque t0= 50 kip-ft/ft is applied on pipe BC. Let G = 11,800 ksi and assume that pipes AB and BC have the same inner diameter, d = 12 in. Pipe AB has a thickness tAB= 3/4 in., and pipe BC has a thickness tBC= 5/8 in. Find the reactive torques at A and C and the maximum shear stresses in each segment.
A spring with ends squared and ground, wire diameter d = 4 mm, outside diameter Do = 40 mm, 18 total coils, and free length Lf = 140 mm has been chosen for an application where the initial deflection is 15 mm and the working deflection is 50 mm. The shear modulus is G= 80 GPa. Part A Determine the clash allowance. Express your answer as a percentage using three significant figures. Part B Determine the spring rate.
Figure shows a cantilever shaft made of steel subjected to several loadingT=5kNm, M=2.5kNm, and P=120kN. If the diameter of the shaft is 60mm, and the yield stress is 310MPa, calculate the safety of factor of the shaft using the Von Mises yield criterion.
A Hollow power transmission shaft of length ‘L’ 1103 mm, outer diameter ‘D’ 73mm and inner diameter 'd' 50. is required to transmit a power of P 60kW at a speed of 2950rpm. The modulus of rigidity of hardened carbon steel, which the shaft is made of, is 79.5 GPa Calculate the angle of twist of the above stating your answer in degrees?