QI\ A ball made of INOX AISI 365 steel with density of 8.52 gr/cm3 was used to determine the viscosity of oil with specific gravity of 0.91. In the viscometer, the ball traveled 19 cm in 2.2 seconds. If the diameter of the ball is 2.95 mm, what is the viscosity of the oil in pa.s ? assume that water density is 1000 kg/m'.

QI\ A ball made of INOX AISI 365 steel with density of 8.52 gr/cm3 was used to determine the viscosity of oil with specific gravity of 0.91. In the viscometer, the ball traveled 19 cm in 2.2 seconds. If the diameter of the ball is 2.95 mm, what is the viscosity of the oil in pa.s ? assume that water density is 1000 kg/m'.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Similar questions

The kinematic viscosity of a liquid is 0.058 cm^2/s and has a density of 500 kg/m^3. What is the absolute viscosity in poise
Please answer only when you are sure and give correct answer Thedensity of an oil at 23°C is 750kg / (m ^ 3) Find its relative density and kinematic viscosity if the dynamic viscosity is 5 * 10 ^ - 3 * kg / m * s .
SAE 10W30 motor oil has a dynamic viscosity of 0.21 kilograms per meter second and a specific gravity of 0.896 (a) What is the density of the motor oil in units of kilograms per cubic meter?
For liquid viscosity measurement, it is desired to create a viscometer consisting of two 30 cm long concentric cylinders. The diameter of the inner cylinder is 20 cm and the diameter of the outer cylinder is 20.2 cm. Since a torque of 0.13 N cinsm is required to rotate the inner cylinder with an angular velocity of 40 rad / s, what will be the viscosity of the fluid in the viscometer in Pa⋅s? Take the value of as 3.
Air with density of 1.225 kg/m^3 and viscosity of 1.789 x 10^-5 kg/m-s flows in a wind tunnel, the wind tunnel spped is measured with Pitot tube probe. For a certain run, the stagantion pressure is measured to be 472.6 Pa gage and the statric pressure is 15.43 Pa gage. Calculate the wind tunnel speed.
A- Womersley number (a) of a human aorta is 20 and for the rabbit aorta is 17, the blood density is approximately the same across the species. The values of viscosity were 0.0035 Ns/m² for the human and 0.0040 Ns/m² for the rabbit. The diameter of the aorta is 2.0 cm for the man, and 0.7 cm for the rabbit, estimate the heart rate beats per minute (bpm) for both species
a submarine is 100 m long, the shape of it hull is roughly cyli9ndrical with a diameter of 15 m. when it is submerged, it cruises at a speed of about 40 kdots or aproximately 20 m/s compute the reynald number, if the viscosity is 1.0x10^-3 pa-s
Find the kinematic viscosity of an oil having density of 980kg/m^2 when at a certain point in the oil, the shear stress is 0.25 Pa and the velocity gradient is 0.3 m/s.
If the viscosity of water at 68 oF is 0.01008 poise, then its absolute viscosity expressed in terms of pound-second per square feet (lb-sec/ft^2) must be
An oil film of thickness 1.5 mm is used for lubrication between asquare plate of size 0.9 m × 0.9 m and an inclined plane having anangle of inclination 200. The weight of the square plate is 392.4 N andit slides down the plane with a uniform velocity of 0.2 m/s. Find thedynamic viscosity of the oil
The volume flow in a water pipe is 9000 m°/h. The pipe length is 80 m, the pipe diameter 1 m. The material data of water are a density of 1000 kg/m? and kinematic viscosity v=10® m7s. A steel pipe with roughness 0.05 mm is used. Determine the pressure drop in the pipe.
The company has opted to purchase a new viscometer for you, as such, you are required by topropose two options for new viscometers. Select two viscometers and explain their operation andconstraints. (P3)b. (P4) Given that you achieved the following results with a U-Tube viscometer:Temperature/ C Time / s40 5760 4180 29100 16Calculate the viscosity at each temperature if the calibration constant is 0.511.d. (M2) Illustrate the results on a graph of temperature vs viscosity and give a briefing on what yourresults indicate, identifying the response of the oil to temperature and explaining anydiscrepancies that may have occurred during the testing.e. (D2) From your testing you discovered that you had a Newtonian and Non-Newtonian sample.Explain to your team what the two terms mean with respect to temperature and shear force onboth samples, giving at least one example of each type of fluid.