QI: A: If the position of a certain body was (-13) unit according to X-axis, then it is moved to be arrived (40) unit according to the same axis (X-axis). Calculate the displacement of this body.

Q: bar rotates about the fixed point ܱ with a constant angular velocity of 2 rad/s. Point A moves…

A: Given:ω=2 rad/sVAh=100 mm/srB=200 mm

Q: Problem 6.1 The following data are referred to Francis Turbine. Net head, H 60 m, speed N= 750 rpm.…

A:

Q: A 100-mm long rod has a diameter of 15 mm. If an axial tensile load of 165 kN is applied, determine…

A: Given data: L=100 mmd=15 mmF=165 kNE=200 GPa Need to determine the change in length.

Q: find the mass of pink, cyan, and orange

A: Given Spring data To find Mass of pink Mass of Cyan Mass of Orange

Q: 7.60. Water is to be pumped from a lake to a ranger station on the side of a mountain (see figure).…

A: Given data: Flow rate = 95 gal/min = 0.005994 m3/sPump power = 8 hp = 5.9656 kWLength of pipe =…

Q: Part 3 Q1) Determine the acceleration of the blocks A and B shown in figure (1). The coefficients of…

A: as per guideline i have to solve only first question of yours

Q: 2 kg mass of saturated water vapor at 300 kPa is isothermally cooled in a piston cylinder until it…

A:

Q: Question 2 Deep groove ball bearings are most widely used bearing type and suitable for many…

A:

Q: Determine the slope and the displacement of the beam at the end of C. A is pin and B is rolle El is…

A:

Q: Discuss the type of stresses that occur when two gears mate with each other, write the equations for…

A: Write the type of stresses that occur when two gears mate with each other.

Q: Which statement is true for the stress strain relationship for the metal shown? E B O Point D is the…

A:

Q: 7. The dry bulb and wet bulb temperature of an enclosed room was 27 deg C and 23 deg C,…

A: Introduction: Dru bulb temperature:(Tdb) The Dry Bulb temperature, sometimes known as "air…

Q: Q2: A 1.78 L four-stroke petrol engine was tested at 2500 rpm. The developed brake power is 28 kW…

A: Given     Volume, V= 1.78 L = 0.00178 m3 Brake power, BP = 28 kW               Speed, N = 2500 rpm…

Q: Oil is poured at a rate of ( Q = 1 L/s) into a conical funnel of (r = 0.3 m), see the figure.…

A:

Q: 03 - Vertical forces are applied to the handle of the pipe wrenches. Determine the moment that these…

A: The given forces are,

Q: Ice or water, which cools a liquid better, if both are at zero centigrade

A: Given Data : Water Ice

Q: The rectangular framework shown in fig. is subjected to t icated non concurrent system of forces…

A:

Q: The rear wheels of the vehicle are driven by the deferential gear system shown in Figure 2. The…

A: Number of teeth in gear A (TA) = 12 Number of teeth in gear B (TB) = 60 Speed of the gear B (NB) =…

Q: E.3) There is a steam system in which the boiler must be fed by using a pump that supplies 0.005…

A:

Q: Q4: The power output of a six-cylinder four-stroke engine is absorbed by a hydraulic WN dynamometer…

A: Given data: Engine type = four stroke Number of cylinder = k = 6 Power output of engine i.e. brake…

Q: dynamometer for which the law is WN 20000 Q4: The power output of a six-cylinder four-stroke engine…

A:

Q: In uniaxial loading the poisson's ratio is 0.30 and the strain in the x- direction is 250 x 10^-6.…

A:

Q: Answer 2

A:

Q: The following statements explain the function of Bar chart in materials selection except: The length…

A: Given question: The following statements explain the function of Bar chart in materials selection…

Q: H.W. Consider two long, slender rods of the same diameter but different materials. One end of each…

A:

Q: 8. How much work is done changing the speed of a 1600 kg sport utility vehicle from 33.0 m/s to 17.0…

A: Given data : Initial velocity (U)=33 m/s Final velocity (V)=17 m/s Mass (m)=1600 kg   Find : Work…

Q: Q2: A two-stroke diesel engine was electrically motored (non-firing operation) when the mete reading…

A: Given     Brake torque, T = 120 N.m               Speed, N = 600 rpm Calorific value, CV = 40.3…

Q: WN 20000 Q4: The power output of a six-cylinder four-stroke engine is absorbed by a hydraulic…

A:

Q: ________distinguises the system from the surroundings. a. boundary b control surface c. control…

A: ________distinguises the system from the surroundings. Answer: a. boundary

Q: A steel bar is stressed to 280 MPa. The modulus of elasticity is 205 GPa. The bar is 80 mm diameter…

A: Given data : Length (L)=240 mm Modulus of elasticity (E)=205 GPa Diameter (d)=80 mm Stress (σ)=280…

Q: 0 0.3 m 70⁰ m 4 kN 15 kN m 0.5 m 6 kN 0.3 m PROBLEM 2/71 1.5 m 10 kN

A: When an amount of force act on an object it has the tendency to rotate the object about a point,…

Q: 1.45 Determine the equivalent stiffness of the system of Fig. 1-46. 2m N E=210 x 10. 1= 3.8 x 10³ m²…

A:

Q: The piston of the hydraulic cylinder gives pin A a constant velocity v = 2.1 ft/sec in the direction…

A:

Q: Quiz F ball initially A 150 tb on the top of a ladder is dropped and hits the ground with reference…

A:

Q: Steam enters a nozzle at 400°C and 700 kPa with a velocity of 10 m/s, and leaves at 320°C and 150…

A:

Q: A 4 3 20 kN B D 3 4 →12 kN C 600

A:

Q: An ideal Reheat-Regenerative engine operates with a boiler pressure of 8 MPa and a condenser…

A: Given: The boiler pressure, Pb = 8 MPa The turbine inlet temperature, T1 = 480 C The reheating…

Q: The thrust generated by a single jet engine a for s F=59000n. It take the plane (with a mass of…

A: Given: m = 6300 kg k = 100000 N/m F = 59000 N s = 0.95 km

Q: members DE, DJ, EJ, and IJ. 2 KN XNK 8m 8m 8m 8m L K J H 1 kN 8m 3 KN 1.5m 2m 8m

A: To find force in member DE,DJ,EJIJ

Q: Q4) Choose the true answer of the following questions : (1) The engine speed is measured…

A:

Q: Determine the modulus of Elasticity E for a material that has proportional stress of 100 MPa and…

A: Given data : Proportional stress=100 MPa Proportional strain=0.001   We have to compute modulus of…

Q: For the ring and the load applied. Calculate the normal stresses at point A and B. Hint: Normal…

A: Given: The axial load on the ring=400 N Because axial load is equally distributed in both parts of…

Q: (2) Find the width of the belt, necessary to transmit 7.5 kW to a pulley 300 mm diameter, if the…

A:

Q: Two reservoirs are connected with a pipeline see figure 2. The first section of the pipeline from…

A:

Q: 4.1) There is a Carnot thermal engine that has a cold focus at 255K and an efficiency of 40%. If the…

A:

Q: Assume F-9 kN. Using RECTANGULAR COMPONENTS, determine the direction of the resultant force,…

A:

Q: Determine the magnitude of the vertical force Cy for the simply supported beam, where w = 8 kips/ft,…

A: given data; w=80kips/ftM=270Kip-ftAB=L1=12ftBC=L2=3ftCD=L3=7ft lets take reaction force at A=RAlets…

Q: Car A rounds a curve of 172-m radius at a constant speed of 37 km/h. At the instant represented, car…

A:

Q: A train which is traveling at 100 mi/hr applies its brakes as it reaches point A and slows down with…

A: Given data: v0=100 mi/hrv1=60 mi/hrs=0.5 mile Need to determine the velocity and acceleration of the…

Q: Q2: The lecturer Aous used to drive his car early inorder to arrive and teach his students some…

A: The time that he should start driving from Baghdad: 7:10 a.m.

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.