The rear wheels of the vehicle are driven by the deferential gear system shown in Figure 2. The pinion gear A on the propeller shaft has 12 teeth and gear B has 60 teeth. The rear axle shafts are connected to the wheels. If the Gear B rotates at 200 r.p.m. and the road wheel attached to axle Q has a speed of 210 r.p.m. while taking a turn, Calculate the speed of axil shaft P.

The rear wheels of the vehicle are driven by the deferential gear system shown in Figure 2. The pinion gear A on the propeller shaft has 12 teeth and gear B has 60 teeth. The rear axle shafts are connected to the wheels. If the Gear B rotates at 200 r.p.m. and the road wheel attached to axle Q has a speed of 210 r.p.m. while taking a turn, Calculate the speed of axil shaft P.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A reverted gear train with a speed ratio of 12 consists of four gear wheels. Gear A has a module pitch of 3mm and is meshed with gear B. Whereas gear C that is meshed with gear D has a module pitch of 2.5mm. Gear B and C form a compound gear system. The distance between axis of rotation of driving gear A and driven gear B is equal to 200mm. If gear A has 24 teeth, determine the suitable number of teeth for all gears.
An epicyclic gear shown in figure below consists of ring gear, planet gear and sun gear. The ring gear has 72 internal teeth and sun gear has 32 external teeth. Planet gear meshes with both ring and sun gears and is carried on an arm which rotates about the centre of the ring gear at 20 r.p.m. If the gear A is fixed, Calculate the speed of plane gear.
Please solve in 30 min The teeth number of each gear is already given (e.g. Z₁ =14). If the rotation speed of gear 1 is n₁=380 r/min, calculate the rotation speed of gear carrier H
The lath machine in the university mechanical workshop uses epicyclic gear train shown in Figure 1 to operate. Plate gear Cof this gear system are carried on the arm A and free to rotated. the pitch circle diameter of the internally toothed ring gear D is to be 214 mm and the module 4 mm. When the ring gear D is stationary, the arm A, which carries three planet wheels C of equal size, is to make one revolution in the same direction as thesun wheel B for every five revolutions of the driving spindle carrying the sunwheel B.Determine suitable number of teeth for all the wheels and the exact diameter of pitch circle of the ring.1.1. Calculate the number of teeth of the ring gear D. 1.2. State an equation tha relate the number of teeth of gear D, B and C. 1.3. Use the table method to calculate the number of teeth of gear B. 1.4. Calculate the number of teeth for gear C.
Two parallel shafts have an angular velocity ratio of 4 to 1 are connected by gears, the largest of which has 40 teeth. Find the number of teeth of smaller gear.
The double-reduction helical gearset shown in the figure is driven through shaft 'a' at a speed of 982 rev/min. The tooth numbers are: N2= 18, N3= 45, N4= 12, N5= 34 Teeth respectively. Calculate the speed of output shaft 'c' in rev/min. Specify a positive number with 2 decimals
The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and driver gears are 86cm and 35cm respectively. If driven shaft runs with 8 r.p.s,determine the following; 1. Center distance between the two shafts in mm. 2. Speed of driver shaft in rpm 3. Velocity ratio 4. Number of teeth's on driver and driven shaft for the given module 5mm
Figure shows an alicyclic gear train with the following details:A has 40 teeth external (fixed gear) ; B has 80 teeth internal ; C - D is a compound wheel having 20 and 50 teeth (external) respectively, E-F is a compound wheel having 20 and 40 teeth (external) respectively, and G has 90 teeth (external). The arm runs at 100 r.p.m. in clockwise direction. Determine the speeds for gears C, E, and B.
A pair of gears having 40 and 20 teeth respectively are rotating in mesh, the speed of the smaller being 2000 rpm. Determine the velocity of sliding between the gear teeth faces at the point of engagement, at the pitch point and at the point of disengagement if the smaller gear is the driver. Assume that the gear teeth are 20° involute form, addendum length is 5mm and the module is 5mm.Also find the angle through which the pinion turns while any pairs of teeth are in contact.
Two spur gears of 24 teeth and 36 teeth of 8 mm module and 20° pressure angle are in mesh. Addendum of each gear is 7.5 mm. The teeth are of involute form. Determine : 1. the angle through which thepinion turns while any pair of teeth are in contact, and 2. the velocity of sliding between the teethwhen the contact on the pinion is at a radius of 102 mm. The speed of the pinion is 450 r.p.m
Two parallel shaft connected by spur gears turn in the same direction and having a speedratio of SR = 4.72 (a) What is the distance of the two shaft, in mm, if the smaller gear is170 mm in diameter? (b) What is the diameter of the larger gear in mm?
A compound epicyclic gear is shown in Fig. for Q.2. C and D form acompound wheel which rotates freely on shaft G. The planet wheels B andE rotate on pins fixed in arms attached to shaft G. C and F have internalteeth: the others have external teeth with the following numbers: A, 40;B, 30; D, 50; E, 20. If A rotates at 500 rev/min and wheel F is fixed,find the speed of shaft G.