Answered: QI- For the given circuit find the…

Engineering

Electrical Engineering

QI- For the given circuit find the generated powers P, Q , AP , and the PF of the source? 30/0° V rms :-j22

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.2MCQ: If the rms phasor of a voltage is given by V=12060 volts, then the corresponding v(t) is given by...

See similar textbooks

Related questions

Q: Find power factor of given circuit 30/0° V rms -j22 42

A: Power factor is the ratio of true power by apparent power. The value of power factor lies in between…

Q: v = 141.4 sin (@ot + 30°) V and i= 11.31 cos (@t - 30° ) find for each (a) the maximum value, (b)…

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: The average real power (P) in an impedance Z = 5/40° 0 delivered by the source v(t Cos (500t-70°) V…

A: Impedance is represented as Z=R+jXZ where R represent resistance , and X represent reactance .…

Q: Homework (1) For the circuit shown in fig.(*), find the rms value of i, VR, and VL e = 63.60 + 100.0…

A: The given circuit diagram is:

Q: Homework (1) For the circuit shown in fig.(*), find the rms value of i, Vr, and VL UR R = 6N e =…

A: The above given circuit has three voltage sources with different frequencies. To calculate circuit…

Q: For the circuit shown, what is the reactive power, Q, consumed by the 1+j5 N load impedance? (Assume…

Q: A impedance of Z = 2553.13°Q is connected across a source with a voltage of 169.706 sin (157.080t)…

A: f) To find the simplified power waveform equation

Q: = 12 cos(200t) V in the following circuit. Use Thévenin's theorem where it will do the best Let v,…

Q: Circuit Diagram C1 10uF ~ 60 Hz 0° Computed Values Compute the expected power factor of the circuit…

A: Capacitive reactance is inversely proportional to capacitance and frequency Inductive reactance is…

Q: find the value of Z₁ in order that Z₁ absorbe the maximum average power -j10 Ω 40 Ω Τε Select one:…

A: Given, ZL=? for maximum power transfer.

Q: 120 V rms Z = 10 +j12 2 60 Hz What is the value of the capacitance that will give unity power…

Q: A capacitor of 3.18 microfarads is connected in parallel with a resistance of 2000 ohms. The…

A: A capacitor of 3.18 μF is connected in parallel with a resistance of 2000 ohms. The combination is…

Q: For the circuit shown below, the average power delivered to the -j5 ohms capacitor is.VAR 10 Ω -j5 Q…

A: Given

Q: For the circuit shown, the load ZL absorbs 2+j3 kVA and it is required to correct the power factor…

Q: 2. Determine the frequency of the following instantaneous equations (no decimal places or whole…

A: We need to find out frequency of given signal .

Q: Identify: a. Three loads are in parallel take the following currents: i1 = 10 sin 314t; i2 = 20 sin…

Q: For the circuit shown, what is the average power, P, consumed by the 18+ j32 load impedance? (Assume…

Q: An ac motor with impedance Z, (4.0 A40) O is supplied by an RMS value of 220-V, 60-Hz source. You…

A: According to question: The real power taken by the load is calculated as

Q: Homework (1) For the circuit shown in fig.(*), find the rms value of i, Vr, and VL UR e = 63.60 +…

A: Superposition Theorem: In a linear active bilateral network consisting no. of energy sources,…

Q: A circuit branch is found to have an equivalent impedance of Z=120−j45Ω. It is given that this…

A: Impedance: Impedance of a circuit is the combination of all the resistance as well as reactance. It…

Q: . Given the circuit below and the associated set of voltages and currents, the reactive Power…

Q: Problem 7.7 For the circuit shown, find V, and the input power factor. 20 kW 16 kW 6/0° A rms 0.8 pf…

A: First find active power and reactive power of each load and than find active , reactive power and…

Q: An industrial load absorbs 200 kVA at power factor inductive of o.5 at 2500 V rms 50 Hz. Find the…

A: Explanation: cosφ1 = Load power factor without capacitor, cosφ2 = Load power factor with capacitor…

Q: The electric field intensity is Ē(-,1)=(2â, – jà,)e¯* in a certain med the average power density if…

A: Average power density

Q: 19.22 72mH V, Z V, -

A: we need to find out phasor V1 . Given:: the load is connected to 100V (rms) and dissipates 1kW at…

Q: 1. Find the equivalent impedance of the given circuit. Use 2kHz as frequency. 50 2 10 mH 100 Q 2 µF…

Q: I RLC Series Circuit wi V=10V, R=1kΩ, XL1=2kΩ, XL2=2kΩ, & XC=7.5kΩ. a. Find Z in rectangular and…

A: (b)

Q: v0- 100 sin(10) at tKO v(0F 200 sin(100) att>0 A coil has been connected to an AC source for a long…

Q: # 1: For the voltage v(t)=12 cos(50t+10°), find: 1. The amplitude (Maximum value) 2. The Root Mean…

Q: C2 The current in an a.c. circuit at any time 't' seconds is given by, i = 120 sin (100xt + 0.36) A.…

Q: Given the following Thevenin equivalent circuit. We connected ZL and its value is chosen to maximize…

Q: 1. A voltage of 22x/r° V (x is the last digit of your student number. For example, if your student…

Q: 11 Q 33 mH 128 322230° Z13 mH Z2 5Ω. 66 µF

A: Let the value of frequency is f = 50 Hz. The expression for the impedance Z1 is given by,…

Q: 2. The current in an a.c. circuit at any time 't' seconds is g n by, i - Im sin (Bat + X) Find (i)…

A: Given : i =Im sin(Bπt+X) Im= maximum current peak value Ipp = 2Im This question they have…

Q: Circuit Diagram V1 C1 220 Vrms 10uF 60 Hz 0° Computed Values Compute the expected power factor of…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: For the circuit shown, what is the complex power, S, average power, P,av, and reactive power, Q,…

Q: five infinite-impedance volunteers,calibrated to read rms values,are connected as shown below. let…

A: First, convert the parameter of the passive elements connected in the circuit in the same unit in…

Q: レ 26,192 5218 v 50 Hz

Q: Problem # 1 Find the phasor transform in rms of each trigonometric function: v(t) = 170 cos (377t -…

A: According to question: c) The PHASOR transform in RMS is calculated as…

Q: 11.47 For each of the following cases, find the complex power, the average power, and the reactive…

Q: Find the average power, the reactive power, and the apparent power absorbed by the load in the…

Q: For the following circuit with sinusoidal input, calculate the following: 1. Total Impedance seen by…

A: "Since you have posted a question with multiple sub parts we will solve first three subpart for you…

Q: EE234 HW #11 1) Find the admittance between nodes a-b in the circuit seen below. Express in both…

Q: The current i(t) through a 10 2 resistor in series with an inductance is given by: i(t) = 3+4 sin…

A: Given, Current, it=3+4 sin100t+45°+4 sin300t+60° A. Resistance, R=10 Ω.

Q: The current in an a.c. circuit at any time 't' seconds is given by, i = 120 sin (100xt + 0.36) A.…

Q: Homework (1) For the circuit shown in fig.(*), find the rms value of i, VR, and VL e = 63.60 + 100.0…

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: The reactance X of inductance L =j/wL True False The reactance X of capacitance =jwc True False The…

A: We need to tell about whether the statement are true or false

Q: 2. From the given circuit, solve for the complex power, apparent power, average power, reactive…

A: Power factor: It tells how much active power is utilized by the circuit from the apparent power. The…

Q: A sinusoidal voltage source V = 46 /115° Vms feeds an impedance with a current I = 2 /52° Ams- The…

A: Given Vrms=46∠115 Volt Irms=2 ∠52 Amp θv=115 θi=52

Concept explainers

Digital Integrated Circuit Design

Digital IC design is a procedural interaction that involves converting determinations and highlights into computerized blocks, which are then further transformed into basic circuits. A significant number of the imperatives related with advanced IC plan come from the foundry cycle and innovative restrictions.

Question

QI- For the given circuit find the generated powers P, Q , AP , and the PF of the source?
30/0° V rms
:-j22

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

P-channel Metal-Oxide Semiconductor (PMOS), N-channel Metal-Oxide Semiconductor (NMOS), and Complementary Metal-Oxide Semiconductor (CMOS)

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The following circuit is powered by a polyharmonic voltage whose expression is: v(t) = 100+141.sin (1000t) + 70.7.sin (2000t) V. It is requested: a) The expression of the instantaneous current.b) Plot the amplitude and phase spectra of the voltage and current.c) The values of the apparent, active, reactive and distortion powers, justifying the results
A capacitor of 3.18 microfarads is connected in parallel with a resistance of 2000 ohms. The combination is further connected in series with an inductance of 795 mH and resistance of 100 ohms across a supply given by e=400 sin + 80 sin(3wt + 60O). Assume w = 314 rad/sec, determine the rms value of the total current.
The values of the parameters in the circuit shown are L1=8 mH; L2=2 mH; k=0.75; Rg=1 Ω; and RL=7 Ω. Ifvg=542 cos 1000t V, find 1. a) the rms magnitude of vo;2. b) the average power delivered to RL;3. c) the percentage of the average power generated by the idealvoltage source that is delivered to RL.
Your Question: Use the following values for the components: Constants I1 = 4 ∠0° [A] I2 = 6 ∠90° [A] ω = 2 000 [rad/s] R1 = 4 [Ω] R2 = 6 [Ω] Randomized L = 1,6 [mH] C = 79 [μF] Use Nodal Analysis to find the rms voltage across the resistor R1, answer in [V] with one decimal.
five infinite-impedance volunteers,calibrated to read rms values,are connected as shown below. let R= 200, L=0.400H,C=6.0 Mf, and V=30.0 v. what's the reading of the voltmeter's V1,V2,V3,V4 and V5 if W= 200 rad/s
Identify: a. A 40 μF capacitor is supplied with a 100 V, 60 Hz source. Find the resulting current. b. Three loads are in parallel take the following currents: i1 = 10 sin 314t; i2 = 20 sin (314t -45º); i3 = 30 cos (314t + 30º) A. respectively. Find the RMS value of the resultant current.
Help me please IN THE CIRCUIT SHOWN, THE VALUE OF THE CURRENT SOURCE IS IN RMS VALUE. DETERMINE: A) THE VOLTAGE (ONLY THE MAGNITUDE) AT THE INDUCTOR TERMINALS, VL B) THE VOLTAGE (ONLY THE MAGNITUDE) AT THE RESISTOR TERMINALS, VR C) THE AVERAGE POWER ABSORBED BY THE 40 Ω RESISTOR
NEED ASAP Pleas answer this problem Maximum Average Power Transfer Pls show full and complete solution
In the circuit of fig below Z1 = 65at an angle -75° and Z2 = 35 at an angle 35° calculate the total (a) apparent power b) real power c) reactive power and d) pf, supplied by the source and seen by sources
An alternating voltage given by v = 120 sin (240t + п / 4) V, is applied to a coil withnegligible resistance and inductance of 100 mH. Determine (a) the reactance of thecoil, and (b) the RMS current flowing through the circuit.
The voltage across it v (t) = 10 . The equivalent of a circuit with cos (2000 . t + 30°) V If the impedance Z = 5 ∠ 60° Ω, what is the average power consumed in the circuit?
The instantaneous power of a parallel RL load is given by 300{1+cos(628.32t+400)} + 400sin(628.32t+400) W. Answer the following (with appropriate units). Real Power: Reactive Power: Apparent Power: