Qi: The E-MOSFET of Figure was analyzed with the result that: k = 0.24 × 10 A/V², VGsQ = 6.4 V, I o = 2.75 mA. (a) Determine gm- || %3D (b) Find ra. (c) Calculate Z; with and without r4. compare results. (d) Find Z, with and without ra. compare results. (e) Find A, with and without ra. compare results. p 12 V 2 k2 1 µF Zo 10 MQ Ip(on) = 6 mA VGS(on) = 8 V VGS(Th) = 3 V Yos = 20 µS V; o 1 µF

Qi: The E-MOSFET of Figure was analyzed with the result that: k = 0.24 × 10 A/V², VGsQ = 6.4 V, I o = 2.75 mA. (a) Determine gm- || %3D (b) Find ra. (c) Calculate Z; with and without r4. compare results. (d) Find Z, with and without ra. compare results. (e) Find A, with and without ra. compare results. p 12 V 2 k2 1 µF Zo 10 MQ Ip(on) = 6 mA VGS(on) = 8 V VGS(Th) = 3 V Yos = 20 µS V; o 1 µF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An optical fiber link with a distance of 30km long has a loss of 0.3dB/km. a) Calculate the minimum optical power level that must be launched into the fiber to maintain an optical power level of 3.0W at the receiving end.b) Estimate the required input power if the fiber has a loss of 0.6dB/km.c) Differentiate, with the aid of diagrams, the types of these dispersions and its effect on the transmission distance. (i) Modal Dispersion(ii) Chromatic Dispersion(iii) Polarization Mode Dispersion
Suppose Rc=10 k, Rb=1k, Vcc=4V, Vi =5V, and β= 200. Find Vbe, Vce, Ic, and the region of operation.
Q.NO.1. Given Data: R1=56KΩ, R2=8.2KΩ, RC=6.8KΩ, RE=1.5KΩ, Β=90, VCC=20V, re=18.44Ω, vs(p)=10mV, RS=200Ω. Determine the value of Av with RL=3KΩ. 2. Calculate the voltage gain if R2 becomes open circuited
Norton's Theorem Compute for IN, RN and the current passing though the 50 ohmresistor, I’.
Design a microstrip line on a 0.5 mm alumina substrate (er = 9.9, tan o = 0.001) for a 50 characteristic impedance. Find the length of this line required to produce an electric length of 270 at 10 GHz,
For an N = 12 mobile system, a 75 MHz bandwidth is available for forward channels, each of which is 200 MHz. (i) Calculate the value of k for this system (ii) How many simultaneous forward calls are possible. (iii) Determine what values of "i" and "j" would satisfy the N = 12 condition, and redraw in your answer scripts in a diagram with co-channels inserted/filled out (iv) If the radius of each cell is 15 km, what would be the co-channel reuse distance, D.
Multiple Choice directions: Circle the letter of the answers 7. This is a special microwave coaxial cable used in the lower microwave bands L, S, and C. a. Flexible coaxial b. All of the above c. Hard line cable d. Braided coaxial 8. The practical microwave region is in the vicinity of a. 1-10 GHz b. 1-20 GHz c. 1-300 GHz d. 1-30 GHz 9. In a hybrid ring, if the signal is applied at port 1, which port has no output? a. 3 b. 2 c. 1 d. 4 Note: Explanation is not needed just provide the correct answers for each number.
A ground-mounted photovoltaic module array for a commercial building may be constructed so that it can be used as? A. a storage area B. a covered walkway C. covered vehicle parking D. a break area for building occupants
Q4 - Calculate the dissipation in power across 20Ω resistor for the FM signal, V(t)= 20 cos(6600 t+ 10 sin 2100 t), if a transmitter radiates a signal of 9.8KW after modulation and 8KW without modulation , Calculate the depth of modulation?
Measure the diameters of the two wires. Given the density of steel is = 7.8×103 kg/m3, theoretically estimate fundamental frequencies of the two wires, and calculate the ratio of their frequenciesr unit length? diameters = 0.254mm and 0.432 mm
A directional coupler configuration with four ports is shown in Figure Q4. A 15 dBm power source is connected to port 1 resulting in coupling factor, C = 15 dB, directivity, D= 25 dB, and insertion loss L=0.5 dB. If all ports are matched,determine the power in dB at ports 2, 3 and 4.
Estimate the optical loss due to Fresnel reflection at a fiber core from GaAs each of refractive indices 1.48 and 3.5 respectively. b) Calculate the optical power emitted into air for the device, when the step index fiber has a numerical aperture of 0.16, coupled power of 0.31 mW.c) Determine the overall power conversion efficiency for the LED if it is operating with a drive current of 210 mA and a forward voltage of 1.5V.d) Find the optical output power at 170MHz, and calculate the optical and electrical modulation bandwidth for a minority carrier recombination life time of 9ns.