QI. for the circuit of flg.,a) Derive the output woltage expression Vo in terns of Ri,R2,Rf,NAIN2.6) Assume Ri =10k, R k, Rf = 90k, V=2U2 =12-t are gien.At whattime the output voltage volts would be 0 Volt'sC) Assume Q1=104, R2= 204, Rf = 2ok andUL=-COSCH),u2=- cos CtJ aregiven. At what time Hae output olt ege would be = Volt ?ifラナwiteNnRIFiniPAVofig. 4

Answered: Image /qna-images/answer/39005dc1-3e8e-4d5e-b4c4-f61981ac36bb.jpg

QI. for the circuit of flg.I, a) Derive the output woltage expression vo in terns of Ri,R2,RfivtI2. b) Assume Ri=10k, R2zk,Rf= 0k, V= t3 ,U2= 2 2-t are giuen. 44 what time the output voltage volt) would be O Vot C) Assume Q1=104, R2= 204, 00-20k and vi-cosct),u2=-cos CtJ are %3D given. At what time Hae output vot ege would be Ub= Volt? if Nn RI マin R2 fig. 4.

QI. for the circuit of flg.I, a) Derive the output woltage expression vo in terns of Ri,R2,RfivtI2. b) Assume Ri=10k, R2zk,Rf= 0k, V= t3 ,U2= 2 2-t are giuen. 44 what time the output voltage volt) would be O Vot C) Assume Q1=104, R2= 204, 00-20k and vi-cosct),u2=-cos CtJ are %3D given. At what time Hae output vot ege would be Ub= Volt? if Nn RI マin R2 fig. 4.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(a) What is the output current IO in the circuitshown if −VEE = −10 V andR = 20 ohm? Assume that the MOSFET is saturated.(b) What is the minimum voltage VDDneeded to saturate the MOSFET if VTN = 2.5 Vand K'n = 0.25 A/V2. (c) What must be the powerdissipation ratings of resistor R and the FET.
In the circuit in the figure IDSS = 12 mA, VP = -8 V, VGSQ = -2.4 V, IDQ = 4.12 mA, Rsig = 10 kΩ, RG = 100 kΩ, RD = 2 kΩ, RS = 470 Ω, RL = 23.7 kΩ and it is known that rd = 20 kΩ. What will be the voltage gain of the circuit? NOTE: The FET output impedance is rd = 20 kΩ and must be taken into account in the calculations.
For the JFET shown in Figure, Determine the minimum value of VDD required to put the device in the constant-current region of operation when VGS = 0 V. where VGS(off) = - 4 and IDSS = 42mA
Explain the concept of Ohm's Law and its relevance in analog electronics. Demonstrate an example and show how it works in amplifier network analysis in the DC or AC domain
In the circuit in the figure, IDSS = 12 mA, VP = -8 V, VGSQ = -2.4 V, IDQ = 4.12 mA, Rsig = 10 kΩ, RG = 100 kΩ, RD = 2.4 kΩ, RS = 470 Ω, RL = 33, It is known that 9 kΩ and rd = 20 kΩ. What will be the voltage gain of the circuit? NOTE: The FET output impedance is rd = 20 kΩ and must be taken into account in the calculations.
Suppose that we have an unusual type of FET for which iD=3 exp(vGS)+0.01vDS2 Here, iD is in mA, vGS is in volts, and vDS is in volts. Determine the values of gm and rd for a Q point of VGSQ=1 V and VDSQ = 10 V.
(a) What are the output currents and output resistances for the current sources as shown if IREF = 45 μA, K'n = 25 μA/V2, VTN = 0.75 V and λ =0.01V−1?(b) What are the currents if IREF is changed to 50 μA?(c) What would be the values if λ =0?
In the Boost DA-DA circuit:Source voltage (E) value: in the range of [17-29] (volts),Switching frequency (f) value: 20 khz,Voltage between load ends: 40VCapacitance value: 470uFPower dissipated at load: 10 watts What is the lowest inductance L, in uH, that can keep the DC-DC converter in continuous current under these conditions? a) 269.3731 b) 415.4375 c) 364.8204 d) 163.6472 e) 578.1875
1. Use the figure below to solve following questions (a) Solve the following dc quantitiesi. VB(Q1)ii. VE(Q1)iii. IE(Q1)iv. VC(Q1)v. VB(Q2)vi. VE(Q2)vii. IE(Q2)viii. VC(Q2)(b) Suppose that the emitter follower is omitted and the output from thecollector of Q1 is capacitively coupled to the 250Ω load, RL. What isthe output voltage across the 250Ω load?
(i) With neat sketch explain the cross sectional view and I-V characteristics of the device which is used in low on state loss and small switching frequency operations. (ii) Write FOUR demerits of the above mentioned power semiconductor device.
amplifier (boost) DC-DA converter circuit, given below; 1- Source voltage (E) value: In the voltage range of [A B] (Volts) 2- Switching frequency (f) value: M kHz 3- Voltage between load terminals (Vload) F (volt) 4- Capacity value is 470 (microF) 5- Pload>= H(watts) consumed per load In which case below do you see the lowest L inductance value in microH that can keep the DC-DC converter in a continuous current state under the conditions? A=25 VOLT B=40 VOLT M= 25kHz F = 55 VOLT H=15 Watts a) 454.5475 b) 382,045 c) 263.62 d) 128.5 e) 581.81
A variety of current source values were applied to the device shownin P2.15(a). The power absorbed by the device for each value ofcurrent is recorded in the table given in P2.15(b). Use the values inthe table to construct a circuit model for the device consisting of a singleresistor from Appendix H.