Q.1) For the state of stress shown below, use stress transformation equations to determine the normal and shear stresses after the element has been rotated (a) 30° clockwise (b) 40° counterclockwise (c) Draw Mohr's circle on scale and show the stresses of parts (a) and (b). 200 MPa 100 MPa 150 MPa

Q.1) For the state of stress shown below, use stress transformation equations to determine the normal and shear stresses after the element has been rotated (a) 30° clockwise (b) 40° counterclockwise (c) Draw Mohr's circle on scale and show the stresses of parts (a) and (b). 200 MPa 100 MPa 150 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At a certain section in a material under stress, direct stresses of 45 MN/m2 tensile and 75 MN/m2 tensile act on perpendicular planes together with a shear stress τ acting on these planes. If the maximum stress in the material is limited to 150 MN/m2 tensile, determine the value of τ.
The principal tensile stress at a point across two mutually perpendicular planes are 100 N/mm2 and 40 N/mm2. The normal, tangential and resultant stresses on a plane inclined at 20° to the axis of the minor principal stress by analytical method is
A plane stress state is given by the principal stresses σx =25 MPa and σy= -11 MPa. Determine σx' in the case that the system is inclined by 30 degrees (counter-clockwise). Give your answer in MPa to the nearest whole number.
a) Prime planes,b) Prime stresses, c) Maximum shear stress and thisin the plane of the stressdetermine the normal stress
A stress element in a rock mass making up a slope experiences a 2D stress as follows: σx = 8 MPa, σy = 4 MPa , tauxy = 3 MPa a. Draw the Mohr circle. On Mohr's circle, mark the location of the x and y planes, mark the angle of rotation θ from the x plane to the σ₁,σ3,and taumax plane. Prove that the angle of rotation of the Mohr circle is 2 times the angle of rotation of the element. b. Write down the coordinates of the center of Mohr's circle and calculate its radius.
Mohr's Circle At a point, the normal and shear stresses acting on one plane are 8000 psf compression and 2000 psf, respectively. On a perpendicular plane, the normal and shear stress combination is 2000 psf compression and 2000 psf. (a) Draw the Mohr's circle. (b) Determine the value of the principal stresses. (c) Find the angle between the plane on which the 8000 psf compressive stress acts and the major principal plane. (d) What is the maximum shear stress acting at the point? kindly answer the following with a complete solution so that i can understand how to solve it. thank you
The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and 55 MN/m2 tension respectively. The shear stress across these planes is 25 MN/m2 (Counter clockwise). Determine the magnitude of the normal, tangential, the resultant stress, and inclination of resultant stress on a plane inclined at 25o to the plane of greater principal stress. And also verify the answer by drawing the Mohr’s circle.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 12 ksi, Sy = 17 ksi, and Sxy = 18 ksi.(a) Draw Mohr’s circle for this state of stress.(b) Determine the principal stresses (σp1>σp2σp1>σp2) and the maximum in-plane shear stress τmaxτmax acting at the point.(c) Find the smallest rotation angle θpθp (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)
A state of stress at a point A is given by σx = 25 MPa, σy = 122 MPa, and τxy = 60 MPa. Determine the equivalent state of stress on an element at the point which represents the principal stresses.
The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and 50 MN/m2 tension respectively. The shear stress across these planes is 30 MN/m? (Counter clockwise). Determine the magnitude of the normal, tangential, the resultant stress, and inclination of resultant stress on a plane inclined at 30° to the plane of greater principal stress. And also verify the answer by drawing the Mohr's circle.
In a biaxial state of stress, normal stress are 900 N/mm^2 and 100 N/mm^3 in x and y diretion respectively. Shear stress is 300 N/ mm ^2. The maximum principal stress will be,
At a point on the free surface of a stressed body, thenormal stresses are 20 ksi (T) on a vertical plane and 30 ksi (C) ona horizontal plane. An unknown negative shear stress exists on thevertical plane. The absolute maximum shear stress at the point hasa magnitude of 32 ksi. Determine the principal stresses and theshear stress on the vertical plane at the point.