Question 1:1. The figure shows two steel shafts connected by a steel pipe with interference. Modulus ofelasticity = 210000MPa, Poisson's ratio = 0.3, and Coefficient of friction = 0.1.Fill the following table:L2InterferenceH6/n5dl58mmS2d2100mmLI70mmL2150mmshaft diameter, d =mmShaft inner diameter, di =mmHole outer diameter, do =mmInterference length =mmCoef. Of friction =Modulus of elasticityPoisson's ratioInterference typeМах.Min.InterferencemicronМраPressure =Force =NTorque =NmmCapacity of the assembly pressAllowable transmitted torqueNmm- LP

Question 1: 1. The figure shows two steel shafts connected by a steel pipe with interference. Modulus of elasticity = 210000MP4, Poisson's ratio = 0.3, and Coefficient of friction = 0.1. Fill the following table: L2 Interference H6/n5 dl 58 mm S2 d2 100 mm LI 70 mm L2 150 mm shaft diameter, d = Shaft inner diameter, di = mm mm Hole outer diameter, do = mm Interference length = Coef. Of friction = Modulus of elasticity Poisson's ratio mm Interference type Мах. Min. Interference micron Pressure = Мра Force= Torque = Nmm Capacity of the assembly press Allowable transmitted torque Nmm

Question 1: 1. The figure shows two steel shafts connected by a steel pipe with interference. Modulus of elasticity = 210000MP4, Poisson's ratio = 0.3, and Coefficient of friction = 0.1. Fill the following table: L2 Interference H6/n5 dl 58 mm S2 d2 100 mm LI 70 mm L2 150 mm shaft diameter, d = Shaft inner diameter, di = mm mm Hole outer diameter, do = mm Interference length = Coef. Of friction = Modulus of elasticity Poisson's ratio mm Interference type Мах. Min. Interference micron Pressure = Мра Force= Torque = Nmm Capacity of the assembly press Allowable transmitted torque Nmm

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 22P

See similar textbooks

Similar questions

For the built-up shape shown in the figure, determine: a. The elastic section modulus considering bending about the horizontal axis. (ANS 518 x 103mm3). b. The elastic section modulus considering bending about the vertical axis (ANS 133 x 103mm3). c. The plastic section modulus about the horizontal axis in x103 mm3 (ANS 572) d. The plastic section modulus about the vertical axis in x103 mm3.(ANS 0.20)
Using DOUBLE INTEGRATION METHOD. Consider 150 mm x 150 mm section and E = 200 GPa. Enter the absolute value only and round-off your answer to 3 decimal places. GIVEN: a = 3.5m b = 16 kn/m c = 16 kn QUESTIONS: 1. Determine the REACTION at A in KN. 2. Determine the SLOPE at A in DEGREES. 3. Determine thw DEFLECTION at B in MM. 4. Determine the DEFLECTION at E in MM. THANK YOU!
20. Situation 22. For the built-up shape shown in the figure, determine: a. The location of plastic neutral axis form the top edge of the flange in mm. ____ b. The plastic section modulus about the horizontal axis. ______ x10^6 mm^3 (3 decimal places) c. The plastic moment with bending about the vertical axis if Fy = 345 MPa. _______kN-m (rounded to the nearest whole number)
Give me right solution From the figure shown, block A weighs 400N and the coefficient of friction between block and the inclined plane is 0.20. Compute the following a) the tension of cable supporting block A if it will have an acceleration of 1.2 m/s2 up the plane. B) the the tension of the cable supporting block B. C) the weight of block B
determine the deflection at E in mm using Double Integration Method Consider 150 mm x 150 mm section and E=200 GPa Enter the absolute value only and round off your answer to 3 decimal places PLS. ANSWER ASAP, I'LL RATE. THANKS
SOM 4.1 Show your complete/correct solution. ( I need detailed solution since there is given answer.) Given answer: Stress of AB = 4294.286 Stress of EF = 6299.130 psi
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Show complete and organized solution. Round-off your answers to two decimal places. a. Vertical Reaction at B in kN. b. Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm.
Note : Read the question carefully and give me right solution according to the question. L=4.1 m
determine the deflection at B in mm using Double Integration Method. Consider 150 mm x 150 mm section and E=200 GPa. Enter the absolute value only and round off your answer to 3 decimal places. PLS ANSWER ASAP. I'LL RATE, THANKS!
Refer to the photo provided. Please make sure your handwriting is readable. Internal pressure and axial tensile force are applied to an open cylindrical tank 605 mm in diameter and 3.02 mm thick, resulting in the final stresses illustrated in the Mohr's circle. If a = 40.10 MPa, b = 100.06 MPa, and c = 45.05 MPa. 1. Determine the kPa value of the internal pressure. 2. What is the axial force's magnitude in kN?
Need answer ASAP. Please be detailed and clear with your solution. IV. The corner of a floating body has a quarter cylinder AB having a length normal to the paper of 3 m. 8) Calculate the magnitude of the horizontal component of the force on AB in kN. *9) Calculate the magnitude of the vertical component of the force on AB in kN. *
Given beam loaded as shown below. Assuming EI is constant. 1. Which of the following gives the location of maximum deflection. a. 2.212 m b. 1.958 m c. 1.334 m d. 1.456 m 2. Which of the following the value of maximum deflection. a. 29.4/EI b. 17.5/EI c. 20.7/EI d. 14.2/EI