one curved surface is shown restraining a body of static fluid. Compute the magnitude of the horizontal component of the force, and compute the vertical component of the force exerted by the fluid on that surface. Then, compute the magnitude of the resultant force and its direction. Show the resultant force acting on the curved surface. In each case the surface of interest is a portion of a cylinder with the length of the surface given in the problem. Water 2.N0 m 1.20-m radius Figure 7:Prob. 3

one curved surface is shown restraining a body of static fluid. Compute the magnitude of the horizontal component of the force, and compute the vertical component of the force exerted by the fluid on that surface. Then, compute the magnitude of the resultant force and its direction. Show the resultant force acting on the curved surface. In each case the surface of interest is a portion of a cylinder with the length of the surface given in the problem. Water 2.N0 m 1.20-m radius Figure 7:Prob. 3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate of 43 kg/s. Another identical elbow is attached to the existing elbow such that the water flow makes a U-turn as shown in the second figure. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference between the centers of the exit and the inlet of the elbow is 50 cm. The weight of the elbow and the water in it is considered to be negligible. Take the momentum-flux correction factor to be 1.03 at both the inlet and the outlet. Take the density of water to be 1000 kg/m3.
Q1(a) Explain the difference between wetting fluid and non-wetting fluid (b) The 60m X 60m rectangular gate shown in Figure Q1(b) has its top edge located 3m vertically below the water surface. The gate is to be opened from its lower edge by applying a normal force by the shaft. Determine the minimum force F required to open the water gate. (Ignore Patm in all your calculations)
Consider laminar flow of a Newtonian fluid in the y direction between two parallel andvertical plates with a distance between h, at steady state. The plate on the left isstationery and the other plate on right-hand side is moving vertically upwards at aconstant velocity Vo. Derive an equation for the velocity profile.
Bernoulli’s equation and represents the sum of velocity head, pressure head and the elevation head above: a. the bottom of the pipe. b. the arbitrary horizontal datum c. the center line of pipe d. the top of the pipeline
The figure shows gate AB, 4 meters high, submerged in water. It is inclined 40 degrees with respect to the horizontal. Using the figure shown, determine the distance of CG (center of gravity) to CP (center of pressure) in meters.
In the figure shown, each block has a mass of 2-kg.Determine the force P needed to start block B to theleft. The angle of friction for all surfaces in contact is16.7 degrees.
in the system shown, determine the value of the force f if the coefficient of friction between the body and floor is 0.41. P is 264.87N
Assuming the conduit in the figure is a 36” wrought iron pipe flowing full, and that the outlet is at point B, calculate the velocity and flow at point B in the pipe considering friction.
A stream of water, 3” in diameter, discharges into the atmosphere at a velocity 80.0 ft/sec. Find the horsepower in the jet using the datum plane through the center of the jet. Draw the figure. And solve using the formula on the Image uploaded.
Determine the magnitude of the applied force P in the figure to cause impending motion without overturning. The mass of the cabinet is 150kg., the coefficient of static friction μs between the contacting surface is 0.35 and theta equals 15°.
The cylinder in the figure below, having a mass of 100 kg is to besupported by the cord that wraps over the pipe. Determine the largest vertical force F that can be applied to the cord without moving the cylinder. The cord passes two times over the pipe (take β = 540° and μS = 0.3).
A vertical pipe is shown in figure 1 below. The pipe tapers from 50 mm in diameter to 25 mm in diameter. If 2 liters of water per minute flow upwards through the pipe the pressure difference across the pipe is 35 kpa. Calculate the flow downwards through the pipe if the pressure across the pipe is to be zero. The losses across the pipe are given by h1=k((v2) ²-(v1)²)/2g,where v1 and v2 are the velocities in the 50 mm and 25 mm sections respectively.