m a tànk through an orifice is to be modeled using water as th flowing fluid. The kinematic viscosity of the oil is eight times that of the water. The relative density of the oil is 0.90. What oil flowrate is represented by 0.002 2 m³/s in the model? If the force exerted on the model tank bottom is 210 N, what is the corresponding force in the prototype?

m a tànk through an orifice is to be modeled using water as th flowing fluid. The kinematic viscosity of the oil is eight times that of the water. The relative density of the oil is 0.90. What oil flowrate is represented by 0.002 2 m³/s in the model? If the force exerted on the model tank bottom is 210 N, what is the corresponding force in the prototype?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

10. The cylindrical container in the figure below weighs 400 N when empty. It is filled with water and supported on the piston. (a) What force is exerted on the upper end of the cylinder? (b) If an additional 600-N weight is placed on the cylinder, how much will the water force against the top of the cylinder be increased? Answer: (a) 51.08 kN; (b) 58.9 kN 250-mm diam A 250 mm B 500 mm?
LABORATORY ACTIVITY APPLICATION OF BERNOULLI'S THEOREM QUESTIONS: 1. As the fluid flows through the section, describe how the velocity, pressure, and elevation heads change. Determine the location of the section's maximum velocity and pressure. 2. What method does the apparatus use to capture energy loss? You could use mathematical equations to explain your point. 3. What will happen to the corresponding kinetic and potential heads if the flowrate passing through the apparatus is increased?
A differential "U"-tube manometer containing mercury of density 13000 kg/m³ is used to measure the pressure drop along a horizontal pipe. If the fluid in the pipe is water and the manometer reading is 0.65m, what is the pressure difference between the two tapping points? Fluid density Pw A B a b datum Manometric fluid density p Hg Figure of manometer setup
one IMG_1085 The plastic block shown below measures I.5 m x/.s m x(.7 m and has a specific gravity of 0.38. The concrete block B (density = 2400 kg/m*) is suspended from the corner of the plastic block by means of a cable and the plastic block is thus floating in the lake (T = 15°C) in the orientation shown. Determine the volume of the concrete block (units of liters) noting that it does not rest on the bottom of the lake. Neglect the weight and volume of the cable in your analysis. %3D 1.7 m 0.5 m Water Cable
Which could be the applied force in Newtons of a moving plate (area 0.1m2) and (v=2m/s) in between two different fluids: %3D over the plate: 3mm of Fluid 1 with viscosity of 0.001 Pa-s under the plate: 4mm of Fluid 2 with viscosity of 0.002 Pa-s O 0.18 O 0.17 O 0.19 O 0.15 O 0.16 O 0.20
The pipe bend shown in the figure is in a horizontal plane. Oil with a specific gravity of 0.86enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa.Determine the force required to hold the bend in place. Neglect any energy loss in the bend.
A plate (0.005 cm )distance from a fixed plate move at ( 72000 mm/min) and requires a force of (2.2 N/m2) to maintain in this speed.Find the viscosity of the fluid between the plates. *
The air exits the nozzle to the atmosphere and enters a vertical plate as shown in the figure. it crashes. The horizontal force required to hold the plate that way is 9 N. Pressure Determine the pressure read on the gauge. Explain under what assumptions a solution can be made. (A1=0,01m2, A2=0,003m2)
please
An engineer sees a water flow through a 0.4 km long and 200 mm diameter pipe having a roughness of 0.0015 mm at 0.075 cubic meter per second. Assuming that the property of H2O is u = 0.001 Nm/sec and p = 1 g/cu.m. He is bored, so he wanted to calculate the following, help him. a. the pressure drop cause of friction b. velocity of H2O in the pipe c. find the Re?
← Fluid Properties The diameter of droplet is 0.075 mm. What is the intensity of the pressure (N/sq. cm) developed in the droplet by surface tension of 0.000075 N/mm?
BULK MODULUS Oil is squeezed in a tank. Calculate its coefficient of compressibility, if pressure p1changes from 0 to 2:5MPa and the initial height of oil h = 1000mm decreases by h =1:8mm.