Question 1 5 Marks The air-oil-water system shown below is at 21°C. Gauge A reads 11 kPa and gauge B reads 14 kPa less than Gauge C. (a) Calculate the density of the oil. What is the reading of Gauge C? (3 marks) (2 marks) (b) air 1 m www 0.65 m oil 0.65 m water 1m B Sc

Question 1 5 Marks The air-oil-water system shown below is at 21°C. Gauge A reads 11 kPa and gauge B reads 14 kPa less than Gauge C. (a) Calculate the density of the oil. What is the reading of Gauge C? (3 marks) (2 marks) (b) air 1 m www 0.65 m oil 0.65 m water 1m B Sc

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: a. A rectangular channel carries 6.0 m³/s. Calculate the critical depth, y, and critical velocity,…

Q: Water is flowing from the tank into a series of pipes and then into the atmosphere through 75…

Q: I. For the truss below, compute for the support reactions. Also, compute for all member forces. II.…

A: Consider the figure, Here, T is the tension and C is the compression.

Q: A reservoir 10m deep has a rectangular weir with a length of 2.5m situated at its short side. When…

Q: Design a reinforcement of a doubly reinforced beam if the beam has a size of 425 mm x 600 mm. Use fc…

Q: 3. Determine the required plastic moment of resistance assuming uniform section of

A: DETERMINATION OF PLASTIC MOMENT CAPACITY OF BEAM SECTION

Q: flows through 0.1m he used

A: S = 0.85 Kinematic viscosity = 1.8 x 10-5 m2/sec Diameter of pipe = 0.1 m Discharge = 2 m3/sec…

Q: Do pont If a horizontal force of 890 N is developed by the water jet leaving the pipe on the 90°…

Q: Determine the equivalent ground length of the canal.

A: This question is from Surveying.

Q: to be constructed on able is at depth 15 pacity and the colum

Q: and the ground is us = 0.3, while the coefficient of static friction between the man's shoes and the…

Q: A new Civil Engineer failing to complete his first building contract worth P70,000 in a specified…

Q: Problem 1 Find the reaction forces of the supports on the beam and the forces in the articulated…

Q: A six-lane freeway (three lanes in each direction) in rolling terrain has 10-ft lanes and…

A: Hi! Thank you for the question, as per the honor code, we are allowed to answer three sub-parts at a…

Q: If 20% of the bolts produced by a machine are defective, determine the probability that out of 4…

A: The probability that out of 4 bolts chosen respective numbers are defective:

Q: An agricultural watershed was urbanised over a period of 30 years. The rainfall loss was 9 mm/hr…

A: Given data:- Urbanized period t= 30 years The value of Rainfall loss before Urbanization is 9…

Q: Determine the maximum tensile stress in the beam. A.1.63 MPa B.2.80 MPa C.0.70 MPa D.1.20 MPa…

A: To determine : maximum tensile stress in the beam. maximum Compressive stress in the beam. maximum…

Q: 4 Assertion (A): When a sharp horizontal curve is to be introduced on a road which already has the…

Q: Compute the maximum bending moment, maxi- mum deflection and the maximum bending stress for a…

Q: 9. A surface float took 10 sec to travel a straight run of a stream of 20 m. What is the approximate…

A: Given that: Straight run of stream of section of 20 m Time taken by float method 10 second.…

Q: Q3) the difference in water surface between two reservoirs is 8m, these reservoirs are connected by…

Q: A T beam has a concrete and steel strengths of 28 MPa and 420 MPa. The live load is 3830 Pa. while…

Q: Write short notes on: (i) Well development (ii) Well spacing

A: Well development Well development is actually defined as the act of cleaning out the clay and the…

Q: A square steel bearing plate placed between the wooden post and the concrete footing. The wooden…

Q: H.W2 Determine the maximum deflection of the simply supported beam. E = 200 GPa and I = 39.9(106)…

Q: Q1 - A 75-Kg man wants to pull a 145- Kg box and the coefficient of static friction between the box…

Q: Determine void ratio Porosity-0.142

A: Given data in question Porosity To find out Void ratio

Q: ← L₁ b ★ PD PL=120 kN L2 → L₁ = 1.5m L₂ = 3 m L₁ WD=52 kN/m WL = 104 kN/m →

Q: For the beam shown in figure, find the deflection and rotation at Free end by using double…

Q: A tract of land has an area of 42 hectares. If this lot is to be protected by a concrete fence,…

A: Considering the area as square plot. Formulae used are : Area = s x s Perimeter = 4 x s s = side…

Q: eir 1.5m high is located in a 5m wide rectangular channel v velocity of approach.

A: WE KNOW THE FORMULA Q=1.84(L)(H+ha32-ha32)ha=va22gva=QB(H+Z)Z=Weir height H=Height upstream…

Q: cally cover all the engineering aspects of Clay

A: Clay soil is a dense soil that benefits from abundant nutrients. In the winter, clay soils are wet…

Q: Calculate the reactions for the shown frame then draw the 40 kN/m 40 kN/m g 2m 2m 2m Q1 bending…

Q: HYDRAULICS Convert all units in SI. Round off to 2 significant figures. Compute the discharge of…

Q: An oil (S = 0.85, v 1.8-10 m/s) flows through 0.1m diameter pipe at 2m³/see, 150m long. Find the…

A: Given data in question Discharge Diameter Specific gravity Roughness Cast iron type To find out…

Q: 3-14. Determine the force in each member of the roof russ State if the members are in tension or…

A: Determine the force in each member of the roof truss?

Q: Q3) the difference in water surface between two reservoirs is 8m, these reservoirs are connected by…

Q: Draw the pictorial isometric view using the two given orthographic projections -50- 25 7 15- 104 15…

A: Isometric view is the 3D view of an object. Below is the isometric projection.

Q: Determine the height to be raised g box mars 12.4kg to gain Potential ener energ of 133 2 J

Q: amount of water needed

A: Generally as per Indian standards or ASTM standards the normal consistency of cement lies between 25…

Q: A lake is 20.50km wide. Considering the effect of earth's curvature and atmospheric refraction, what…

Q: SITUATION 6 The hull of a boat has a volume of 180 m³, and the total mass of the boat when empty is…

A: Volume of hull of boat = 180m3 Total mass of boat when empty = 8560 kg specific gravity of sea water…

Q: 1.) A beam carries the loading shown. Design a rectangular timber beam if the permissible stresses…

Q: Given ten (10) units of isolated rectangular footing, 1.20m x 2.00m x 0.30m, reinforced with 10pcs…

A: Rates are taken from CPWD DSR

Q: numbers 4 and 5

Q: V No.4: AND SAND 20¹ > FIV. 0-361 Ton Cross Section Area: 400 in² K=5.0 x, 10-² cm/sec Find Q Flow…

Q: Determine the moisture content in percent if the rod penetration is 9 mm.

Q: epare a datasheet and calculate the cost of plastering cement (1:5), 20mm thick for 50m². Also…

A: Given data:- Ratio of plastering cement is 1:5 Thickness of plaster is 20 mm Area of plastering is…

Q: ISA 90*60*8 mm of steel of grade fe-410 is connected to a 12mm gusset plane ans is used a tension…

A: Welded connections are provided in steel structures since it is lighter, quicker, adapting and gives…

Q: Q1) A-Assume a system of pipe containing pump and turbine has enlargement and contraction in…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A closed tank contains 0.610 m of mercury (SGmercury = 13.6), 1.524 m of water, 2.438 m of oil of specific gravity 0.750, and an air space above the oil. If the pressure at the bottom of the tank is 276 kPa gage, what should be the reading at the top of the tank? Express your answer in kPa.
What height of a column of special gage liquid (spec. gr.= 2.95) would exert the samepressure as a column of oil (spec. gr.= 0.84) 15 ft. high?a. Write the given and required.b. Illustration of the problemc. Solution
Medium oil having a sp.gr. of 0.90 flows through a 120 mm diameter pipe with a mean velocity of 5.3 m/s and friction factor of 0.01. Oil has an absolute viscosity of 0.04 Pa.s. Compute the velocity at 40 mm from the center of the pipe. Group of answer choices 9.845 8.459 4.589 5.489
The air-oil-water system is shown in figure. If gage A reads 17psi absolute andgage B reads 2.2psi less than C, compute the unit weight of oil in pcf (pounds percubic feet). Use unit weight of air equal to 0.76pcf. Also compute the gauge reading point at C.
Please answer all questions. I will rate. Oil of specific gravity 0.80 and dynamic viscosity of 0.05 Pa-s flows at a rate of 100 lit/sec through a 80 m of 150 mm diamater pipe. If the head lost is 4m, determine the Note:Choices are given Reynolds number (13,581.22, 15,831.22, 18,351.22, 12,521.82) Maximum velocity in m/s (1.67, 7.61, 6.17, 71.6) Maximum shear stress in Pa (14.72, 21.74, 41.27, 17.42) Velocity 30 mm from the centerline of pipe in m/s (4.99, 5.99, 6.99, 3.99)
A tank contains three liquids; kerosene (s= 0.80), crude oil (s=0.90) and sea water (s=1.05) with depths of 0.60 m, 0.40 m, 0.80 m respectively. An orifice 100 mm diameter is located at the bottom with a discharge of 29 L/s. Knowing that the diameter of tank is 1.2 meter. Determine the the time to remove both sea water and crude oil only. a. 34.5 sec b. 62.3 seconds c. 70.2 seconds d. 63.6 seconds e. 59.8 seconds.
A tank contains ail sp. gr. 0.80, gasoline sp. gr. 0.90 and seawater sp. gr. 1.03. If the depths of the liquids are 0.5 m, 0.8 m and 1 m for oil, gasoline and seawater respectively. Find the pressure at a depth of 1.2 m. a. 28.124 Kpa b. 21.092 Kpa c. 16.04 Kpa d. 10.104 Kpa The answer for this is letter D which is 10.104 Kpa however I dont know the exact solution.
Questions #1 Water flows at the rate of 0.16 L/s through a 200 mm diameter pipe. If its Viscosity is 1.15x10^6 m^2/s what is the type of flow? A. Subcritical B. Turbulent C. Supercritical D. Laminar Questions #2 From the steel pipe network shawn in Figure, the supply of water is 350 lit/sec. Calculate the following: a) Rate of flow of water in pipe 2 in Lit/s ( A. 151.7 , B. 198.3 C. 167.2 , D. 175.1) b) Rate of flow of water in pipe 4 in Lit/s ( A. 151.7 , B. 198.3 C. 175.1 , D. 198.3)
The discharge of water collected from a constant head permeameter in a period of 15 minutes is 400 ml. The internal diameter of the permeameter is 6 cm and the measured difference in heads between the two gauging points 15 cm a part is 40 cm. Calculate the coefficient of permeability in mm/s. a. 5.9 x 10^-2 b. 4.8 X 10^-1 c. 2.15 x 10^-2 d. 625 X 10^-2
The discharge of water collected from a constant head permeameter in a period of 15 minutes is 500 ml. The internal diameter of the permeameter is 5 cm and the measured difference in head between two gauging points 15 cm vertically apart is 40 cm. Calculate the coefficient of permeability in mm/s. a.0.106 b.0.3788 c.1.23 x 10^(-2) d.0.750
A U-tube differential manometer connects two pressure pipes A and B. Pipe A contains carbon tetrachloride having specific gravity 1.594 under a pressure of 117.72 kPa and pipe B contains oil of sp. gr. 0.8 under a pressure of 117.72 kPa. The pipe lies 2.5 m above pipe B. Find the difference of pressure measured by mercury as fluid filling U-tube.A. 120.58. Choose the best answer below: a.31.36 cm of mercury b.25.11 cm of mercury c.64.74 cm of mercury d.13.62 cm of mercury
Medium oil having a sp.gr. of 0.90 flows through a 120 mm diameter pipe with a mean velocity of 5.3 m/s and friction factor of 0.01. Oil has an absolute viscosity of 0.04 Pa.s. Compute the velocity at the center. CHOICE: 3.60, 6.003, 6.30, 3.006