19:48people.utm.myQuestion 1a) A gas turbine plant is reported to have thermal efficiency of 35.9% in a simple cycle modeand to produce 159 MW of net power. The pressure ratio is 14.7 and the turbine inlettemperature is 1288°C. The mass flow rate through the turbine is 1,536,000 kg/h. Takingthe ambient conditions to be 30°C and 100 kPa.i) Sketch the plant schematic diagram.ii) Determine the isentropic efficiency of the turbine, %.iii) Determine the isentropic efficiency of the compressor, %.iv) Sketch the cycle on a T-s diagram.b) This plant is then fitted with a regenerator with a thermal ratio of 0.65.i) Sketch the plant schematic diagram.ii)Sketch the T-s diagram of the cycle.iii) Determine the thermal efficiency of the plant, %.Take for air, Cp = 1.005 kJ/kg.K and y = 1.40 while for combustion gases, Cp = 1.15 kJ/kg.Kand y = 1.33.<

Answered: Image /qna-images/answer/3ae1879d-5b95-4988-854c-7c861f1e64ff.jpg

Answered: Question 1 a) A gas turbine plant is…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Write legibly so i can understand 4. In a Brayton cycle, air enters the compressor at 101.32 kPaa and leaves at a pressure of 808 kPaa. The air is heated to 717 o C in the combustor. For a net output of 2125 kW, compute: a) Mass flow rate (kg m/s ), b) power to drive compressor (kW), c) Gross power (kW) , d) thermal efficiency, e) mean effective pressure (kPaa)
Superheated steam at 10,800 kPa and 580°C, enters the 1st stage turbine and expands to 300 kPa. It is then reheated to 340°C before entering the 2nd-stage turbine where it expands to a condenser pressure of 10 kPa. The net power output is 100, 000 kW. The turbine and pump efficiencies are 82%. Determine for the cycle: (a) the network per unit mass of steam flow in kJ/kg (b) the heat transfer rate to steam passing through the boiler and the heat transfer rate to cooling water passing through the condenser in kJ/s (c) the thermal efficiency.
Problem 1: The boiler of a power steam cycle operates at 6000 kPa and the condenser at 50 kPa. At the entrance to the turbine, the temperature is 500°C. The isentropic efficiency of the turbine is 90 percent, pressure and pump losses are negligible, and the water leaving the condenser is subcooled by 6.3°C. The boiler is sized for a mass flow rate of 18 kg/s. You are asked to: a. Represent the cycle on P-v and T-s diagrams. b. Compute the rate at which heat is added in the boiler. c. Compute the power required to operate the pumps. d. Determine the net power produced by the cycle. e. Compute the thermal efficiency.
31 - The temperature of the water vapor at the entrance to a turbine is 400ºC and the pressure is 4.5 MPa. The pressure of the saturated steam water at the turbine exit is 75 kPa and the mass flow rate is 41 kg/s. What is the turbine power? a) 21.69 MW B) 15.52 MW NS) 24.55 MW D) 18.96 MW TO) 22.28 MW
Steam enters the turbine of a power plant operating on the Rankine cycle (Fig. 2) at 873.15 Kand exhausts at 30 kPa. To show the effect of boiler pressure on the performance of the cycle,calculate the thermal efficiency of the cycle and the quality of the exhaust steam from theturbine for boiler pressures of 5000,7500, and 10 000 kPa. #Chemical Engineering #Chemical #Thermodynamics
in a rankine cycle, what is the entrance pressure of the turbine if the condenser pressure is 105 kpa and the pump work is 20 kj/kg. use density of water entering the pump, 950 kg/m^3.
3) Combined Cycle (CC) Natural Gas Power: Cheap natural gas (mostly fromfracking and similar extraction techniques) and CC gas plants are one of theprimary reasons that US carbon emissions peaked in ∼2010 and has been declining. Here, natural gas powers a Brayton cycle turbine, and the exhaustfrom that turbine is then fed into a steam generator to run a Rankine cycleturbine.a) The high temperature in the Brayton cycle turbine is 1500K. The exhaust for the Braytoncycle exits at about 850K. What is the maximum efficiency that you could expect from aheat engine operating between these two temperature extremes? b) A heat exchanger is able to deliver the Brayton cycle exhaust to a Rankine (steam) cycle.The the final outgoing temperature from this steam cycle is 325K. What is the maximumefficiency that you could expect to achieve operating between the high temperature fromthe Brayton cycle and the low temperature from the Rankine cycle? (That is, what is thetheoretical max efficiency of the…
1. A steam power plant operates on Rankine cycle. The steam enters the turbine at 7MpA and 550 degrees celsius with a velocity of 30m/s. It discharges to the condenser at 20kpa with a velocity of 90m/s. For a flow of 37.8 kg/s. Determine: a. The schematic and T-S diagram of the cycle. b. The enthalpies on each state. c. Total Heat added d. Heat rejected in the condenser e. Net work f. Cycle EfficiencyP.S. Please help me with this question. Im having a hard time with this. Thank you very much and please show your solution.
A turbojet aircraft moving with a velocity of 790 ft/s at a runway where the pressure& temperature is found to be 14.7psi & 546R. The axial flow compressor provides apressure ratio of 14 to 1. Temperature at the turbine inlet is 2000R. The mass flowrate of airinside the engine is 133 lbm/s. Determine the following:a. T-S diagramb. Pressure & temperature at each statec. Thrust force (lbf)d. Propulsive power developed (BTU/min)e. Propulsive Efficiency
Consider below ideal reheat Rankine Cycle (operating with water):a) Draw T-s diagramb) Mass flow ratec) Thermal efficiencyd) Thermal power supplied to the burnere) Carnot efficiencyf) Second law efficiency of this cycle xx=40 , yy=20
Superheated steam generated in a power plant at a pressure of 8,600 kPa anda temperature of 500 ℃ is fed to a turbine. Exhaust from the turbine enters acondenser at 15 kPa, where it is condensed to saturated liquid, which is thenpumped to the boiler.(a) What is the thermal efficiency of a Rankine cycle operating at theseconditions?(b) What is the thermal efficiency of a practical cycle operating at theseconditions if the turbine efficiency and pump efficiency are both 75%?Which of the two efficiencies has greater impact on the thermal efficiency?(c) Sketch both cycles in the same T-s diagram.(d)If the power output of the turbine is 80,000 kW in case (b), calculate themass flow rate of the working fluid.(e) Calculate the heat transfer rates in the boiler and the condenser. Doublecheck the result for the condenser.(f) For both cases (a) and (b), make a comment about the operation of turbine(issue of cavitation). [one sentence is fine](g) How you would operate the condenser of a practical…
Air enters the compressor of a regenerative gas-turbine engine at 100 kPaand 300 K and is compressed to 800 kPa. The regenerator has aneffectiveness of 65 percent, and the air enters the turbine at 1200 K. For acompressor efficiency of 75 percent and a turbine efficiency of 86 percent,determine(a) The heat transfer in the regenerator.(b) The back work ratio.(c) The cycle thermal efficiency

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS