Prpblems for pressureQuestion (1):- Find the pressure in the pipe shown in figure.ifPmer=13600kg/mand pw=1000kg/m'.80 mm160 mmWatermercuryQuestion (2):- Find the pressure in the pipe shown in figure ifPmer=13600kg/m'.30 mm50 mmmercury

Answered: Image /qna-images/answer/7aceb5cb-7237-480c-85ad-c03047b91275.jpg

Answered: Question (1):- Find the pressure in the…

Question (1):- Find the pressure in the pipe shown in figure.if Pmer=13600kg/m' and pw=1000kg/m. 80 mm 160 mm Water mercury

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

7. A cylindrical pipe with water flowing downward at 0.02m ^ a / s has a top diameter of 0.08 m and boom diameter 0.04 m and the height of 1.5 m. Find the pressure difference between the pipes.
Design a pipe system to supply water at 20° C from the elevated tank to the demand point at the discharge rate of 2.5 m3/s (see figure below). Take these steps:1. Identify your system elements. You have 400 m long pipe system that has one 90° bends. 2. Account for minor losses caused by the bend (use K = 0.18), by the valve (use K = 0.2), entrance loss from elevated tank to pipe (use K = 1) and exit loss from pipe to demand point (use K = 0.5) 3. Set the Energy equation to find the total head loss magnitude (hL). 4. Break down the total loss into friction (hf) and minor losses (hM). Use D-W and minor loss equations to find a relationship between Diameter (D) and Friction Factor (f) (both are unknown). In the equation, replace velocity with Q/A to have only D and f as unknowns. 5. Your other equation to find the 2 unknowns is the Moody diagram. Because both equations are non-linear, numerical iteration is needed. After contacting a nearby vendor, you realize that a convenient pipe…
6. Water at a rate of 60 GPM flows in a 3 inch-diameter pipe at 100 psia and 150 F. Find a) the volumetric flow rate, b) mass flow rate, c) mass flux, and d) flow velocity. Note: At P = 100 psia and T = 150 °F: v = 0.01634 ft³/lb. Explain the step by step, and draw a figure or free body diagram.
For the hydraulic system of Figure, the following data are given: The pump is adding2.984kW to the fluid.(a) Pump flow is 0.00158 m3. (b) The pipe inside diameter is 0.01905m.(c) The specific gravity of the oil is 0.9.(d) The oil tank is vented to the atmosphere.(e) The head loss HL between station 1 and 2 is 12.19m.(f) The elevation difference between stations 1 and 2 is 6.096m.Find the pressure available at the inlet to the hydraulic motor(station 2).
A large tank is partly filled with oil (s.g.= 0.85), the air space above being under pressure. A 50 mm ϕ hose connected to the tank discharges on the roof of a building 15.25 m above the level in the tank. The friction loss is 5.50 m. What air pressure in KPa must be maintained in the tank to deliver 0.0124 m3/s on the roof?
A water pump is used to pump water from one large reservoir to another large reservoir that is at a higher elevation. The free surfaces of both reservoirs are exposed to atmospheric pressure, as sketched in Fig. The dimensions and minor loss coefficients are provided in the figure. The pump’s performance is approximated by the expression Havailable = H0 − aV.2 , where the shutoff head H0 = 125 ft of water column, coefficient a = 2.50 ft/(gpm)2 , available pump head Havailable is in units of feet of water column, and capacity V. is in units of gallons per minute (gpm). Estimate the capacity delivered by the pump
A geothermal well produces from total depth at 1000m and produces dry (saturated) steam with a temperature of 200°C. Shut-in wellhead pressure is 5000kPa, and the wellhead flowing pressure is 1000kPa when the well is flowing 100 tons/hour. Determine the downhole pressure and temperature in each case ( for shut-in case and the flowing case). Assume: Casing diameter =0.2m a Casing roughness =0.0005m Please answer fast i give you upvote.
Impeller in a centrifugal pump as shown in the figure is connected to the shaft with CONICAL CLEANER. The power to be transmitted by the motor is P = 23 kW. Its revolution is n = 1822 rpm. Width of the conical joint is b=96mm, Conical angle α = 1 degree, Friction coefficient μ =0.3. The conical connection is tightened up to the limit of the surface safety pressure (Pem=39 N/mm2, the shear safety stress of the shaft τem=22 N/mm2) After finding the required SHAFT DIAMETER, HOW MUCH IS the connection safe or not in order to transmit this force. (Attention! and the ratio of the torque coming from the motor gives safety)
water is being delivered at a rate of 2000 gpm for a reservoir to a subdivison below resvoir height=220ft length of pipe= 1500ft final aubdivisiion= 24ft, 20psi 1)determine the normal pipe size 2) if the pipe size is not avalible what size combination will work 3) if we used a 8 inch pipe determine the min thickness 4)determine the max pressure that can deelope in the 8in system
pressure different is 2200 kN/m2 and pipe length is 98m
Two pipes 1 and 2 having the following properties are connected in series: Pipe 1 - Length = 1500m, Diameter = 850mm f= 0.025 Pipe 2 - Length = 1200m, Diameter = 650mm f= 0.020 It is required to replace these two pipes with a single pipe whose length is 2700m. Assuming that the friction factor for the new pipe is 0.015, what is the required pipe diameter?
choose the correct answer Q1A- Losses of pressure in fluid due to resistance by viscose shear stresses are: * a) Minor losses b) Fitting losses c) Friction losses d) Total head losses e) None of all above B- when pipe with the different diameter are connected by series, then total losses will be the sum of each pipe losses * a) True b) False