As shown in the Video and in the figure below, water "bubbles up" 9 in. above the exit of the vertical pipe attached to three horizontal pipe segments. The total length of the 0.75-in.- diameter galvanized iron pipe between point (1) and the exit is 27 inches. Determine the pressure needed at point (1) to produce this flow. (1) (2) 9 in. 10in. (3) P1 = the tolerance is +/-2%

As shown in the Video and in the figure below, water "bubbles up" 9 in. above the exit of the vertical pipe attached to three horizontal pipe segments. The total length of the 0.75-in.- diameter galvanized iron pipe between point (1) and the exit is 27 inches. Determine the pressure needed at point (1) to produce this flow. (1) (2) 9 in. 10in. (3) P1 = the tolerance is +/-2%

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As shown in figure below, oil can be siphoned from a tank using a flexible hose, provided that the end of the hose at Point B, is below the free surface in the tank at Point A. The maximum elevation of the hose is at Point C. Oil is being siphoned from the tank through a constant-diameter hose. The end of the siphon at Point B is 6.71 meters below the oil top surface level of the tank at Point A. If the gauge pressure at Point C is 90.257 KPa and the density of oil is 890 fraction numerator k g over denominator m cubed end fraction , the vertical distance between Point C and Point B in meters is
A pipe AB carries water and tapers uniformly from a diameter of 4" at A to 8" at B over a length of 6 ft. Pressyre gauges are installed at A, B and also at C, the midpoint of AB. If the pipe centerline slopes upwards from A to B at an angle of 30° and the pressures recorded at A and B are 2.0 and 2.3 bar, respectively. (1 bar = 14.5 psi) Illustrate the problem before answering the following questions: (a)determine the flow, in ft^3/s through the pipe at C neglecting all lossess. (1 bar = 14.5 psi) (b)determine the pressure in bars, recorded at C neglecting all losses.
Water flows in a pipe of 1-in. diameter at a temperature of 70°F. The pressure values at points 1 and 2 are found to be 20 psi and 25 psi, respectively. The elevation of point 1 is 12 feet, and the elevation of point 2 is 0 feet. There is 15 feet of pipe between the two points. a. Determine the direction of flow. b. What is the minimum discharge above which the flow will not be laminar?
A pipe AB carries water and tapers uniformly from a diameter of 4" at A to 8" at B over a length of 6 ft. Pressure gauges are installed at A, B and also at C, the midpoint of AB. If the pipe centerline slopes upwards from A to B at an angle of 30° and the pressures recorded at A and B are 2.0 and 2.3 bar, respectively. (1 bar = 14.5 psi) Illustrate the problem before answering the following questions:
Question 7 A liquid, with a density of 850 kg/m3 , is flowing downwards through a vertical pipe from a point a to a point B.The diameter at A is 150mm and the diameter at B is 75mm.Point B is 2.4m below point A.If 21 dm3 /s of the liquid flows through the pipe, the pressure gauges (connected at A and B) indicates a pressure difference of 12kPa.The loss of head across the pipe between A and B is given as KV2 /2g , where V is the velocity at A.Calculate the value of K.
PROBLEM 3: A venturi meter with a throat diameter of 6 cm is fitted in a horizontal pipeline of 12 cm diameter with oil of specific gravity 0.88 flowing from left to the right. The difference in level in the two limbs of a mercury manometer connected to the tapping points read 12 cm and the connecting pipes are filled with the same oil. (a) If two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet. Determine the difference between the 2 gage pressure readings in kPa.
The flow carried by pipe below discharges into the open atmosphere. If the pipe length is 300 m, diameter is 150 mm and roughness of 0.0025 mm, write the equation(s) required to determine the maximum discharge.
12. Points A and B are 3000 ft apart along a 10-in. new steel pipe. B is 220 ft higher than A. With a flow of 3.2 efs of water from A to B, what pressure must be maintained at A if the pressure at B is to be 50 Ib per sq in.? Answer should be: 164 lb per sq. inch Show your handwritten solution.
A pipe AB carries water and tapers uniformly from a diameter of 10cm at A to 12cm at B over a length of 2 m. Pressure gauges are installed at A, B and also at C, the midpoint of AB. If the pipe centerline slopes upwards from A to B at an angle of 30° and the pressures recorded at A and B are 2.0 and 2.3 bar, respectively. (1 bar = 100 kPa). Illustrate the problem and show your complete solution.
A pump test for air flow is set up as shown below in which the pump draws air from the atmosphere into the 1-ft diameter pipe. The liquid in the differential manometer is water (? = 62.4 ?b/??^3) and the density of air is 0.00238 ?lug/??^3. Assume that the air flow is incompressible and frictionless. (a) Using the piezometer tube, compute the pressure in the pipe. (b) Using the Pitot tube and an energy equation, compute the velocity in the pipe. (c) Assuming that the air far away from the entrance to the pump is at rest (zero velocity), calculate the power delivered by the pump.
A differential pitot tube located at the center of a cylindrical air tube produces 2.6 in. of water pressure. What is the velocity at the impact end of the pitot tube? The impact gauge reads 2.6, 2.6, 2.5, 2.1, 1.8 when placed at points 1-5 in Fig. 3.10. What is the average velocity in the tube? What factor would be applied to the center reading to indi- cate a true average velocity? Note: In actual practice it would be necessary to check this factor through the entire range of velocities to be encountered, because variation may be expected.
Q1: In a venturemeter used for measuring the flow ofoil (-0.85) through a horizontal pipeline, the pipe diameter is 2.4 times the diameter at the throat. Connections are made from the entrance to the meter and the throat to a vertical L tube containing mercury If the difference level between the fluids in the U - tube arms is (x +) in em, where S.N. is student serial number. Neglect friction in the pipe. Find an expression in terms of x for the velocity of the oil in the pipe.