QUESTION 2 A combinational circuit with four inputs (A, B, C, D) and one output (Z) is designed as follows using an 8:1 multiplexer. Inputs A, B, C are connected to the select lines S2. S,.S, respectively. Multiplexer has the following values connected to the data inputs: I,,I = D; 14.13 = 1; 1,,1, = 1; I2.1, = D' For the circuit given above a) Fill the truth table. b) Using the Karnaugh map, simplify the output function as the sum of the products and write the simplest logic expression of the circuit realized above Z = f (A, B, C, D).

QUESTION 2 A combinational circuit with four inputs (A, B, C, D) and one output (Z) is designed as follows using an 8:1 multiplexer. Inputs A, B, C are connected to the select lines S2. S,.S, respectively. Multiplexer has the following values connected to the data inputs: I,,I = D; 14.13 = 1; 1,,1, = 1; I2.1, = D' For the circuit given above a) Fill the truth table. b) Using the Karnaugh map, simplify the output function as the sum of the products and write the simplest logic expression of the circuit realized above Z = f (A, B, C, D).

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter29: Service-entrance Calculations

Section: Chapter Questions

Problem 3R: a. What is the ampere rating of the circuits that are provided for the small-appliance loads? _____...

See similar textbooks

Similar questions

Apply lasso analysis to find i Commentary: PLEASE, describe the procedure step by step, in detail. Do not do it on paper, digitally here :)
Type your question here Two resistors connected in series and at differing temperature are shown below. (a) Derive relations for the noise – equivalent resistor and temperature ???, ???. (b)Calculate ???, ??? for the specific case where: ?1 = 1?Ω , ?2 = 2?Ω , ?1 = 300 ?2 = 390 ?
14.a. Which test can be used to measure splice loss?A. Tensile measurementB. OTDRC. Bit error rate testD. Continuity test14.b. Which type of fiber optic cable is usually supplied with an attached connector?A. Patch cordB. Tight-buffered cableC. Loose-tube armored cableD. Standard loose-tube cable14.a. Which of the following features would usually be found in direct-burial cable but not in overhead cable?A. Steel armorB. Strength membersC. Outer jacketD. Fiber housing
This true or false Question from DIGITAL COMMUNICATIONS Course,just write for me the final answer. q14)
EENG226 SIGNALS AND SYSTEMS PLEASE SOLVE JUST. E. And make sure the answer is correct and solved it step by step ??
What Zm? Break down simply how they got the answer to a,b,c for someone who does not understand?
In a closed-loop system, the system transfer function (G(s)) and the controller's transfer function (C(s)) areit is given as follows. According to this, the system is divided into a unit step, ramp and a parabolic entrancefind the permanent status error that it will give.
A wind farm is being built on an island 6km offshore and needs to be connected to the power grid substation 12km down shore before it can become operational. The cost of laying cable under water is $10,000/km, and the cost of laying cable on land is $8,000/km. a) Determine the cable route that will minimize cost. b) What is the minimum cost
Q1) Solve the Inequalities and Express the solution as intervals. Also, show each solution set on the real line : (solve 5 only) (10 pt. ) ? < ? − ? -4 ??+?? ≤ ?+? -1 ??? 2- ?(?−?)? ?? ? ≤ ? − ? ?? - 3
Explain code
The following problems refer to grounding requirements. Give the source of yourresponses. 1. If they are present, what items are required to be bonded together to form a groundingelectrode system?
This question from mobile communication course. This course from telecommunications Engineering.