Answered: Question 2: Consider the network shown…

Question 2: Consider the network shown in the following figure. Compute the magnitude of the line voltages at the load. 0.1 N jo.1 n A 10 0 ja 1 a

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: 1. Two wattmeter are used to measure the total power drawn by a balanced delta connected load. If…

Q: The input power to a 3-phase load is measured as 8kW. If the line voltage and power factor of the…

Q: The input power to a 3-phase load is measured as 10kW. If the line voltage and power factor of the…

A: In this question we will find line current..

Q: The input power to a 3-phase load is measured as 16kW. If the line voltage and power factor of the…

Q: The input power to a 3-phase load is measured as 17kW. If the line current and power factor of the…

Q: Find the line currents in the unbalanced three-phase circuit of Fig. 1 and the real power absorbed…

Q: Two wattmeters are connected into a 3-phase, 3-wire, 220V line indicate 3.5kW and 1.5kW. If the…

Q: A 100 km long transmission line is loaded at 100 KV.If the loss of line is 15 MW and the load is 150…

A: Given: S=150 MVAVL=100 kVPLoss=15 MW

Q: Q2: A single phase line is transmitting 1,100KW power to a factory at 11KV and at 0.8 pf lagging. It…

A: Given: The resistance is R=2Ω, The reactance is X=3Ω, The power factor is cosθ=0.8, The power is…

Q: determine the line-to-neutral (120 V)

Q: If the line has a length of 30 km., what is the real power loss along the line if the voltage across…

A: In this question we need to find a power loss in line

Q: A transmission line having a characteristic impedance of 75 ohms is delivering power to a 150-ohm…

Q: 52.56 rps The input power to a 3-phase load is measured as 11kW. If the line current and power…

A: Given data The input power Pin = 11kW. If the line current IL = 23 A and power factor cos(phi)=…

Q: The input power to a 3-phase load is measured as 12kW. If the line voltage and power factor of the…

A: We need to tell about line current from given power .

Q: A three phase transmission line has a resistance of 10 Ω and reactance of 80 Ω per wire. The load…

A: The solution is given below

Q: Determine the amplitude of the line current in a three-phase system with a 300 V line voltage that…

Q: ) Find the ICA load current. b) Give the line voltage Vab. c) Calculate the total complex power…

A: In the circuit a) Find the ICA load current. b) Give the line voltage Vab. c) Calculate the total…

Q: The input power to a 3-phase load is measured as 16kW. If the line voltage and power factor of the…

Q: A balanced Y-connected load absorbs in total 3 kW at a power factor of 0.6 lagging. If th line…

A: Given, A balanced Y-connected load absorbs, Total power, PL=3 kW Power factor, cosθ=0.6 lagging Line…

Q: Find out the sending end voltage (Vs) and %efficiency for the given readings VR(line to line)=…

A: Given VR(line to line)=382 vcosϕR=0.8IR=0.63 AResistance R=24 ΩXL=24 Ω

Q: Q18. 415V, 3-phase, 4 wire, system supplies shown star-connected three loads Figure Determine (a)…

Q: If the |Vs| = |Vr| = 25kV (Three Phase) and the line reactance X 8 ohm per phase. The maximum power…

A: NOTE: We’ll answer the first question since the exact one wasn’t specified. Please submit a new…

Q: The following information is given in connection with a parallel connected load of three impedances:…

A: In parallel circuits, Voltage across the load is constant but current vary which depends on the type…

Q: Three unequal single-phase loads are connected across the lines of a balanced, 3- phase, 230 volts…

Q: 8. A 415-V, 3-phase, 4-wire system supplies power to three non-inductive loads. The loads are 25 kW…

A: Question-4 is not in the question. As per the policy we can solve only one question, please…

Q: A 3-phase transmission line operating at 10 kV has a resistance of 192. The percentage resistance of…

A: Given, A 3-phase transmission line with, Rated line voltage, V = 10 kV Resistance, R=1 Ω Base kVA =…

Q: A three-phase supply, with an effective line voltage of 240 V, has an unbalanced delta connected…

A: In delta connection line voltage is equal to phase voltage and line current is equal to 3 times of…

Q: A three-phase generator supplied 3.6 kVA at a power factor of 0.85 lagging. If 2500 W are delivered…

A: Given data: pf=0.85Pload=2500 W

Q: The input power to a 3-phase delta connected load is measured as 3.3KW. If the line voltage and line…

Q: A three-phase supply, with an effective line voltage of 240 V, has an unbalahced delta connected…

Q: The input power to a 3-phase load is measured as 12kW. If the line current and power factor of the…

A: The input power to a 3 phase load is measured as 12kW.If the line current and power factor of the…

Q: The input power to a 3-phase load is measured as 16kW. If the line current and power factor of the…

A: As per guidelines i have to attempt first one . please post remaining again Given data Input power…

Q: The input power to a 3-phase delta connected load is measured as 3.7KW. If the line voltage and line…

A: Power in three phase =sqrt(3)×Line vo3×Line current×power factor. Given 3 phase power =3700 W Line…

Q: h a total length of 50 km. The apparent power S is 100 kVA, the line voltage is 3.3 kV. Calculate…

A: The given line has a distributed parameter as they are the function of length. It is used in the…

Q: A current is measured at the neutral ground of a star load, of equal impedances in all three phases.…

A: In this question we need to choose a correct option

Q: The input power to a 3-phase load i measured as 13kW. If the line voltag power factor of the load…

Q: Two wattmeters are used to measure the total power drawn by a balaced delta connected load. If the…

A: For balanced loads The power drawn is same Power drawn by three phases is the sum of two wattmeters…

Q: Question 2: Consider the network shown in the following figure. Compute the magnitude of the line…

A: In the network, 3 phase generating system supplied to 3 phase balance load through transmission…

Q: The input power to a 3-phase load is measured as 18kW. If the line voltage and power factor of the…

A: input power P=18 kW Line voltage VL=430 V power factor=0.7 line current IL=? IL=P3×P.F.…

Q: For the system shown in the figure below, if the sending-end voltage V, is 220 V, the line impedance…

A: Given Vs = 220 V, Zline = 0.1+j 0.4 ohm, IL = 2 ∠-30° A

Q: The input power to a 3-phase load is measured as 17kW. If the line voltage and power factor of the…

Q: 1. An 11kV,3 phase transmission line has a resistance of 1.5 ohms per phase and 12.73 milli henrys…

Q: A 380 V system as shown below, obtain the line currents and phase voltages * 1j 3+2j 2-3) 1-4j LWHE

A: In the question as shown in the figure. A 3 phase balance Delta load supplied the power to 3 phase…

Q: The input power to a 3-phase load is measured as 8kW. If the line current and power factor of the…

Q: Find % Regulation for the given readings VR(Line to Line ) = 207 Volts, VS(Line to Line ) = 243…

A: We know voltage regulation formula is %R= Vs -Vr/(Vr)

Q: The input power to a 3-phase load is measured as 14kW. If the line current and power factor of the…

A: Given Three phase supply Input power, P = 14 KW Line Current, I = 26A Power factor = 0.7 To find…

Q: 2. A single phase 11 kV line with a length of 15 km is to transmit 500 kVA. The inductive réa line…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Line Current (i) ii) Line voltagel iii) Power factor of the circuit

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: Queston 2. 50 paver changes is MW/kv50. The Seresitvity of, line Voltage anod that to reactue pawer…

A: Given Real power change of line voltage ∆P∆V=50 MW/KV Reactive power change of line voltage…

Q: 2- The per unit value of the 50 transmission line in the figure below is ... .. Sbase is 50 MVA and…

A: Most of human energy requirement is meet by generating electrical energy. Once electrical energy is…

Question

Lesson: Electric Machine's
Please Quick

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Introduction

VIEW

Solution

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A short 3, 3 wire transmission line has an impedance per wire of 15+j20 Ω. The sending end line to line voltage is 13,200 V and the receiving end load takes 1,000 kW at a lagging power factor and the current per conductor is 70 A. What is the receiving end voltage and power factor? Note: draw the current and voltage vector diagram to facilitate your solution.
Estimate the distance over which a load of 15000 KW at p.f-0.8 lagging can be delivered by a 3-phase T.L having conductor each of resistance 0.8 2 per km the voltage at the receiving end is to be 132 KV and the losses in the line is to be 5% of received power
Three 230V single phase loads are supplied from a 400V 50Hz 3 phase 4 wire supply. The loads supplied are as follows a. 10Kw at a unity power factor connected between L1 and neutral. b. 15 kVA at 0.8 lagging power factor connected between L2 and neutral. c. 8kVA at 0.7 lagging power factor connected between L3 and neutral. Calculate a. The current in each line conductor. B. The current in the neutral conductor
A three phase 60 Hz transmission line delivers 750 KW at 95% leading power factor and at delta voltage of 6,900 volts. The resistance per conductor is 4.3 ohms and the reactance per conductor is 2.6 ohms. Assuming both source and load are wye connected, what is the load impedance per phase? A. 69 ohms B. 64.5 ohms C. 72.2 ohms D. 60.27 ohms
A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the apparent power supplied by the generator. The apparent power supplied by the generator is _____ VA.
c) For a transmission line w/characteristic impedance Z0 = 50 W. At some point of the line, a forward wave has the voltage V+ = 10V and backward wave has the voltage V- = 4V. i) Currents of the forward wave and backward wave at that point. ii) Measured voltage and current at that point. d) A transmission line has the following properties: Length, L = 3 m. Characteristic impedance Z0 = 50 W. The load impedance ZL = 100 W. And phase constant b = p/3. Assume the forward voltage at z = 0 is VA =10ejp/4 At z = 3m, calculate: i) Forward voltage and forward current. ii) Backward voltage and backward current. iii) Measured (total) voltage and current across the load
A three-phase line has an impedance of 0.1+j0.8 Ω/ϕ. The line feeds two balanced three-phase loads connected in parallel. The first load is absorbing a total of 630 kW and absorbing 840 kVAR magnetizing vars. The second load is Y-connected and has an impedance of 15.36−j4.48 Ω/ϕ. The line-to-neutral voltage at the load end of the line is 4000 V. What is the magnitude of the line voltage at the source end of the line?
In the system given below, Za=Zb=Zc= (25+j5) Ω.a) Find the line currents?b) Calculate the total average, reactive and complex powers?
A balanced three-phase source furnishes power to the following three loads:Load 1: 6 kVA at 0.83 pf laggingLoad 2: unknownLoad 3: 8 kW at 0.7071 pf leadingIf the line current is 84.6 A rms, the line voltage at the load is 208 V rms, and the combined load has a0.8 pf lagging, determine the unknown load.
In the figure, the circuit is given as VRS =√3 . 60V and Zy = 6 + j8. Find the value of C to be connected in order to make the power drawn from the system in a phase 1, to make the load current 1, and to make cos(φ) 1.
AC Power and Power Factor 1. Two loads are connected in parallel across a 13,200-volt line. Load A draws 200kW at 0.6 p.f. (lagging), load B takes 200kVA at 0.8 p.f. (lagging). Find the reactive, apparent and true power and the line current.
A 4200-V, three-phase transmission line has an impedance of 4+j ohms per phase. If it supplies a load of 1 MVA at 0.75 power factor, find: (a) the complex power (b) the power loss in the line (c) the voltage at the sending end. *Ans. S=0.75+j0.66 MVA, PL=25.14 kW and VS=4.492∠ − 1.912°kV Use four decimal places.