Question 2: Find the transfer function (eo / e;) in the electrical circuit given in Figure 2 and answer the following questions. (R1 R2 R3 R4 R5 = R6 = 200 k and C = 10 uF, C2 5 µF) a. Show zeros and roots in the complex plane. b. Make the stability analysis of the system. c. Write eo (t) for ei (t) = u (t) (unit step signal). R, C2 R, C, R, R, e, R3 Figure 2.Electrical Circuit for Question 2

Question 2: Find the transfer function (eo / e;) in the electrical circuit given in Figure 2 and answer the following questions. (R1 R2 R3 R4 R5 = R6 = 200 k and C = 10 uF, C2 5 µF) a. Show zeros and roots in the complex plane. b. Make the stability analysis of the system. c. Write eo (t) for ei (t) = u (t) (unit step signal). R, C2 R, C, R, R, e, R3 Figure 2.Electrical Circuit for Question 2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ANSWER THE FOLLOWING QUESTIONS Given the closed loop system, what is the forward transfer function? a. 0.1Ks b. 0.1 c. K / [(1 + K)s + 1] d. 0.1K / [(1 + K)s + 1]
a) get the equation of motion by drawing the free body diagram of the given system.b) get the transfer function of the system. Ɵ(s)/T (s) = ?Show all decals in detail.
3. The __________ is, in essence, a switch which closes for a brief period oftime and then open, closing and opening many times a second. 4. The ___________ is a way to tell how many frequency components are neededto make up a signal.
Measurements conducted on a servomechanism show the system response to be: C (t) = 0.3 e 60t + 1.5 e 10t, when subjected to a unit step input. [1].Obtain the expression for the closed-loop transfer function. [2].Determine the undamped natural frequency and damping ratio of the system.
The CT signal x(t)=3cos (600πt) + 6cos2(mπt) is critically sampled (Nyquist rate)by fs=4000 Hz. Find:i. The value of m.ii. The frequency components of the signal.iii. The frequency resolution (∆f) of the output spectrum if the sampled signal isprocessed by 64 point-DFT.iv. Define frequency resolution.
1. The CT signal x(t)=3cos (600πt) + 6cos2 (mπt) is critically sampled (Nyquist rate)by fs=4000 Hz. Find:i. The value of m.ii. The frequency components of the signal.iii. The frequency resolution (Δf) of the output spectrum if the sampled signal isprocessed by 64 point-DFT.iv. Define frequency resolution.
II. 3 use this system: \[ y(n)=x(n)-x(n-2)+0.8 y(n-1)-0.64 y(n-2) \] a) Draw its block diagram b) b. 1 - Obtain its transfer functionH(z) b. 2 - Calculate and PLOT∣H(ejθ)∣, forθ=0,π/4.π/2,3π/4, andπ. c) Obtain and plot its poles and zeros, in the z-plane
1. find the transfer function (H(p)= S(p)/E(p)) of the circuit 2. what happens to H(p) if we consider R1=0. What system is it? 3. what happens to H(p) if we consider R2=0. What system is it?
Consider the following signal: f(t) = 0 if t < 0f(t) = 1 − 0.5t if 0 ≤ t < 2f(t) = 0 if t > 2 a) Give the graphical representation of the signal (f). b) Give a physical meaning of the convolution product of two signals. We set h (x) = f (t) *f (t) where '*' represents the convolution product. c) Determine the signal (h). d)Give the graphical representation of the signal (h).
a)Generally Explain the drawing rules and formulas of the Nyquist curve. b) G(?)=K [(S−1)(S−2) / (S+2)(S+3)] ; Fow above G(s) please Construct nyquist curves for K=1, 5/3, 9 values. Write down the Nyquist stability criterion and explain whether the system is stable or not.Enclosed please find the plot of same G(s) function. c) Define the gain and phase margin, this time on the nyquist curve.
Hi can you help me about this question? The figure shows a vehicle crash test simulation. Since the simplified model of the bumper of this vehicle is as follows, a- Find the transfer function of the system. X (s) / F (s) =? b- Assuming that the force F (t) is 1000 δ (t) N, find the displacement x (t). k=5000 N/m b=6000 N*s/m m= 1000 kg δ(t)=Dirac Delta
In the figure, the input signal of the system is x (t) and the output signal is y (t). In this system, there is a sub-system with frequency response H (f). The frequency response H (f) of this subsystem is given at the top of the figure and defined as c = 800, k = 2. In addition, the frequency of the cosine signal shown in the figure is given as fc = 4000.x(t)= 4cos(8000πt).cos(1200πt)Find the output signal Y (t) and calculate the value at t = 1/4 , Y = 1/8 =?Given that the input signal of this system x (t) is defined as