Question 2 For a motorbike absorber system, a helical compression spring with squared and grounds ends is to be designed with given force and deflection requirement as shown in Figure 4. Given the condition that the preload of motorbike weight, 500 N is loaded on the compression spring and additional load produce deflection of 60 mm. Presetting is to be used. The loading is static. Given that the spring material shear modulus is 79 GPa and shear force correction factor is 1.0644. The clash allowance is 10% of the maximum deflection The tensile 500 N of strength of the spring is 1650 MPa. Determine 500 N 1000 N F, 60 mm Clash allowance Music wire with d = 5 mm Figure 4

Question 2 For a motorbike absorber system, a helical compression spring with squared and grounds ends is to be designed with given force and deflection requirement as shown in Figure 4. Given the condition that the preload of motorbike weight, 500 N is loaded on the compression spring and additional load produce deflection of 60 mm. Presetting is to be used. The loading is static. Given that the spring material shear modulus is 79 GPa and shear force correction factor is 1.0644. The clash allowance is 10% of the maximum deflection The tensile 500 N of strength of the spring is 1650 MPa. Determine 500 N 1000 N F, 60 mm Clash allowance Music wire with d = 5 mm Figure 4

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.8.6P

See similar textbooks

Similar questions

A bungee jumper having a mass of 55 kg leaps from a bridge, braking her fall with a long elastic shock cord having axial rigidity EA = 2.3 kN (see figure). If the jumpoff point is 60 m above the water, and if it is desired to maintain a clearance of 10 m between the jumper and the water, what length L of cord should be used?
The inclined ladder AB supports a house painter (85 kg) at C and the weight iq = 40 K/m} of the ladder itself. Each ladder rail (t5= 4 mm) is supported by a shoe (ts= 5 mm) that is attached to the ladder rail by a bolt of diameter d = 8 mm
A bumping post at the end of a track in a railway yard has a spring constant k = 8.0 MN/m (see figure). The maximum possible displacement d or the end of the striking plate is 450 mm. What is the maximum velocity vmaxthat a railway car of weight W = 545 kN can have without damaging the bumping post when it strikes it?
A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
A 10-ft rigid bar AB is supported with a vertical translational spring at A and a pin at B. The bar is subjected to a linearly varying distributed load with maximum intensity q0. Calculate the vertical deform at ion of the spring if the spring constant is 4 kips/in.
Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
A block weighing W = 5.0 N drops inside a cylinder from a height h = 200 mm onto a spring having stiffness k = 90 N/m (see figure), (a) Determine the maximum shortening of the spring due to the impact and (b) determine the impact factor.
-11 A rubber cube R of a side L = 3 in. and cross- sectional area A = 9 in2 is compressed inside a steel cube S by a force F = 5 lb that applies uniformly distributed pressure to the rubber. Assume E 0.3ksi and,, = 0.45. (a) Calculate the lateral pressure between the rubber and steel (disregard friction between the rubber and the steel, and assume that the steel block is rigid when compared to the rubber). (b) Calculate the change in volume of the rubber.
A helical spring is provided with a rigid plate at each end. A bolt passes through the spring and the end plates. By turning the nut, the spring is compressed until the coils touch. The height of the unloaded spring is 600 mm, its mean coil diameter is 100 mm and the diameter of the spring wire is 28 mm. The spring has 18 coils. The diameter of the bolt is 25 mm and the plates are each 25 mm thick. Calculate the elongation of the bolt when the spring is fully compressed as well as the stress in the spring wire (take E = 200 GPa and G = 80 GPa).
PROBLEM: 5 A helical valve spring is to be designed for an operating load range of 90N to 195N. The maximum deflection of the spring for this load range is 7.5 mm. Assuming a spring index of 9, a permissible shear stress of 550 N/mm2 for the material and the modulus of rigidity of 0.85x105 N/mm2. Determine the dimensions of the spring. (i.e. Diameter of the spring wire ,Mean coil diameter, Outer diameter of the spring, number of active turn and free length of the spring). Assume the spring coil is squared and ground.
A square end compression helical spring has an operation load range of 3.5KN to 4.2KN.The deflection for the load range is 8mm and the spring index is 6.if the permissible shear stress and module of rigidity for the material of the spring are 380MPa and 90pa respectively, including the effect of the wire curvature. Design the spring by, determine (A)wire diameter (B) mean coil diameter (C) number of active turns (D)total number of turns
a helical compression spring with squared and ground ends is ti be made of a steel wire 79 gpa and presetting is to be used. the operation load of the spring can be considered static. If the maximum working force is 292 N and a force of 35 N is required when the spring is 30 mm longer, determine the spring constant k