Homework Help is Here – Start Your Trial Now!
Engineering
Computer Engineering
Question 2 n Figures 2, 3, 4 and 5 the designation of the state of the MISO signal is "Hi-Z" before and after the SS signal is low. This means the output driving the signal is turned completely off and not driving the signal either high or low. "Hi-Z" means "High mpedance". Also in the figures, the designation of the state of the MOSI signal is "XXX" before and after the SS signal is low. This means the state of the signal is "Unknown" or "Don't Care". f there are multiple Slaves on the bus, why must a Slave turn off the driver (Hi-Z) on their MISO signal when their SS signal is high and the slave is not selected? Questions 3 The article defines four SPI Modes or configurations numbered 0, 1, 2 and 3. Which mode corresponds to the setup shown in this diagram. The blue trace is the data signal and the red trace is the clock. 3.0 2.01 1.0 0.0 Data - AS -1.0 SPLDecoder 0 -2.0 -3.0 -4.0~ -5.0 -1.0 .. 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0

Question 2 n Figures 2, 3, 4 and 5 the designation of the state of the MISO signal is "Hi-Z" before and after the SS signal is low. This means the output driving the signal is turned completely off and not driving the signal either high or low. "Hi-Z" means "High mpedance". Also in the figures, the designation of the state of the MOSI signal is "XXX" before and after the SS signal is low. This means the state of the signal is "Unknown" or "Don't Care". f there are multiple Slaves on the bus, why must a Slave turn off the driver (Hi-Z) on their MISO signal when their SS signal is high and the slave is not selected? Questions 3 The article defines four SPI Modes or configurations numbered 0, 1, 2 and 3. Which mode corresponds to the setup shown in this diagram. The blue trace is the data signal and the red trace is the clock. 3.0 2.01 1.0 0.0 Data - AS -1.0 SPLDecoder 0 -2.0 -3.0 -4.0~ -5.0 -1.0 .. 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0

Computer Networking: A Top-Down Approach (7th Edition)
Computer Networking: A Top-Down Approach (7th Edition)
7th Edition
ISBN:9780133594140
Author:James Kurose, Keith Ross
Publisher:James Kurose, Keith Ross
Chapter1: Computer Networks And The Internet
Section: Chapter Questions
Problem R1RQ: What is the difference between a host and an end system? List several different types of end...
See similar textbooks
icon
Related questions
Question
100%

here is the link

https://www.analog.com/en/analog-dialogue/articles/introduction-to-spi-interface.html

 

Read this article about the SPI bus and answer the 3 questions below. Submit your answers to Canvas. Introduction to SPI Interface e Question 2 In Figures 2, 3, 4 and 5 the designation of the state of the MISO signal is "Hi-Z" before and after the SS signal is low. This means the output driving the signal is turned completely off and not driving the signal either high or low. "Hi-Z" means "High Impedance". Also in the figures, the designation of the state of the MOSI signal is "XXX" before and after the SS signal is low. This means the state of the signal is "Unknown" or "Don't Care". If there are multiple Slaves on the bus, why must a Slave turn off the driver (Hi-Z) on their MISO signal when their SS signal is high and the slave is not selected? Questions 3 The article defines four SPI Modes or configurations numbered 0, 1, 2 and 3. Which mode corresponds to the setup shown in this diagram. The blue trace is the data signal and the red trace is the clock. 3.0 2.0% 1.0 0.0 Data - AS -1.0 SPLDecoder -2.0 -3.01 -4.0 -5.0 -1.0 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0
Transcribed Image Text:Read this article about the SPI bus and answer the 3 questions below. Submit your answers to Canvas. Introduction to SPI Interface e Question 2 In Figures 2, 3, 4 and 5 the designation of the state of the MISO signal is "Hi-Z" before and after the SS signal is low. This means the output driving the signal is turned completely off and not driving the signal either high or low. "Hi-Z" means "High Impedance". Also in the figures, the designation of the state of the MOSI signal is "XXX" before and after the SS signal is low. This means the state of the signal is "Unknown" or "Don't Care". If there are multiple Slaves on the bus, why must a Slave turn off the driver (Hi-Z) on their MISO signal when their SS signal is high and the slave is not selected? Questions 3 The article defines four SPI Modes or configurations numbered 0, 1, 2 and 3. Which mode corresponds to the setup shown in this diagram. The blue trace is the data signal and the red trace is the clock. 3.0 2.0% 1.0 0.0 Data - AS -1.0 SPLDecoder -2.0 -3.01 -4.0 -5.0 -1.0 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0
Expert Solution
steps

Step by step

Solved in 3 steps

SEE SOLUTIONCheck out a sample Q&A here
Blurred answer
Recommended textbooks for you
Computer Networking: A Top-Down Approach (7th Edi…
Computer Networking: A Top-Down Approach (7th Edi…
Computer Engineering
ISBN:
9780133594140
Author:
James Kurose, Keith Ross
Publisher:
PEARSON
Computer Organization and Design MIPS Edition, Fi…
Computer Organization and Design MIPS Edition, Fi…
Computer Engineering
ISBN:
9780124077263
Author:
David A. Patterson, John L. Hennessy
Publisher:
Elsevier Science
Network+ Guide to Networks (MindTap Course List)
Network+ Guide to Networks (MindTap Course List)
Computer Engineering
ISBN:
9781337569330
Author:
Jill West, Tamara Dean, Jean Andrews
Publisher:
Cengage Learning
Concepts of Database Management
Concepts of Database Management
Computer Engineering
ISBN:
9781337093422
Author:
Joy L. Starks, Philip J. Pratt, Mary Z. Last
Publisher:
Cengage Learning
Prelude to Programming
Prelude to Programming
Computer Engineering
ISBN:
9780133750423
Author:
VENIT, Stewart
Publisher:
Pearson Education
Sc Business Data Communications and Networking, T…
Sc Business Data Communications and Networking, T…
Computer Engineering
ISBN:
9781119368830
Author:
FITZGERALD
Publisher:
WILEY
SEE MORE TEXTBOOKS