Question 2: The following water turbine generates 750 W of power when releasing water from the tank. The pipes are made of cast iron. a. Calculate the flow rate of water b. Calculate pressure losses through the tube c. Calculate all minor pressure losses through accessories H = 25 m Water D = 6 cm L = 20 m Turbine D=5 cm L = 30 m

Question 2: The following water turbine generates 750 W of power when releasing water from the tank. The pipes are made of cast iron. a. Calculate the flow rate of water b. Calculate pressure losses through the tube c. Calculate all minor pressure losses through accessories H = 25 m Water D = 6 cm L = 20 m Turbine D=5 cm L = 30 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The water is pumped from a 40 sch pipe that has 750 ft lenght, 6 in. nominal diameters. Height difference between exit and entry planes is stated as 50 ft. The yield of waterpump, 80% the power of pump motor is 20 horsepowers. Friction losses are stated as 50ft-lbf/lbm. Please calculate the flow rate in pipe line.
A hydroelectric plant has a dam with a gross height of 381 m with respect to the collectors and a turbine-generating system with 86% efficiency. the estimated water flow is 110m3/s. The pressure losses in the pipeline have been estimated at 34m. Calculate the number of 116mw pelton turbines required.
A pump draws 24 li/s of water from the lower reservoir and lifts it to upper reservoir. The head lossfrom the inlet 150 mm pipe diameter is three times the velocity head and the head loss going to theoutlet 100mm pipe diameter is 25 times its velocity head. What is the power generated by the pump tothe system in horsepower. (Note: Velocities from the reservoir are different from the velocities of thepipe and pleaseee draw a diagram if you can thank you so much)
Use figure below Question : Water at 20 C is to be pumped through 2300 ft of pipe from reservoir 1 to 2 at a rate of 2.5 ft3/s, as shown in the figure. If the pipe is galvanized iron of diameter 7 in and the pump is 75% efficient, what horsepower pump is needed? Neglect minor losses. HINT : pumped through 2300 ft of pipe from reservoir 1 to 2 at a rate of 2.5 ft3/s, & galvanized iron of diameter 7
The figure shows a portion of a fire protection system in which a pump draws water at 60°F(v=1.21 x10-5 m² from a reservoir and delivers it to a point B at the flow rate of 1500 gal/min. Calculate the required height of the the water level in the tank in order to maintain 5.0 Psig pressure at point A
Water recirculates at a volume flow rate of 0.4524 ft3/min from the blade outlet to the impeller, and shaft sealing losses are negligible. A centrifugal pump has a hydraulic efficiency of 95% and a mechanical efficiency of 93%, respectively. Calculate the pump efficiency in percent if the pump delivers water at a flow rate of 12 ft3/min.
Pressure drop across a turbine is 30 psi, the flow rate is 60 gpm. Calculate the power output of the turbine
Oil of specific gravity 0.750 is pumped from a tank over a hill through a 24′′ pipe with the pressure at the top of the hill maintained at 25.5 psi. The summit is 250 ft above the surface of the oil in the tank, and oil is pumped at the rate of 22.0 cfs. If the lost head from tank to summit is 15.7 ft, what horsepower must the pump supply to the liquid? Indicate the Free Body Diagram
Francis and Kaplan turbines are often provided with drafttubes, which lead the exit fl ow into the tailwater region, asin Fig. . Explain at least two advantages in using adraft tube.
the diameter of the suction pipe is 385mm. The diameter of the discharge pipe is 268mm. If centrifugal pump delivers 322388 L/hr of water to a pressurized tank with 293kpa. The source of water is 14m below the pump. Calculate the pump total head in meters.
Gasoline at 38°C is being drawn from a closed tank having a pressure of 70kPag. The level of gasoline in the tank is 2.5m above the pump centerline. The suction line friction loss is 0.6m. The vapor pressure of the gasoline is 48kPa absolute and its specific gravity is 0.72. Determine the NPSH available.
The turbine of a micro-hydroelectric power plant delivers 65hp at 75% efficiency. If the effective head is 115ft, how many cubic feet per minute of water must be used.