The water is pumped from a 40 sch pipe that has 750 ft lenght, 6 in. nominal diameters. Height difference between exit and entry planes is stated as 50 ft. The yield of waterpump, 80% the power of pump motor is 20 horsepowers. Friction losses are stated as 50ft-lbf/lbm. Please calculate the flow rate in pipe line.

The water is pumped from a 40 sch pipe that has 750 ft lenght, 6 in. nominal diameters. Height difference between exit and entry planes is stated as 50 ft. The yield of waterpump, 80% the power of pump motor is 20 horsepowers. Friction losses are stated as 50ft-lbf/lbm. Please calculate the flow rate in pipe line.

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter34: Emission Control Diagnosis And Service

Section: Chapter Questions

Problem 2RQ: What will result from too little EGR flow? And what can cause a reduction in the flow?

See similar textbooks

Similar questions

The flow rate of a hydraulic fluid with a Sg of 1.08 through a 2-in. I.D. orifice is 50 gal/min. If the pressure drop across the orifice is 5 lbf/in.", what is the discharge coefficient?
A lift pump was used to collect water at 60 strokes per minute and 50 liters was collected. The lift pump has a bore of 10 cm and stroke of 15 cm. What is the volumetric efficiency of the lift pump?
A Kaplan turbine runner is to designed to develop 10000 hp, the net head is 5.5 m. Assume that the speed ratio is 2.09 and the flow ratio is 0.68, and the overall efficiency is 60%. The diameter of the boss is 1/3 rd of the diameter of the runner . The discharge is ؟
The suction diameter of 60mm reads 2psi vaccum and 50mm diameter discharge with 250kpag. The suction water level is 5m above water pump center line and discharge water level is 25m above the pump center line. The total head loss at suction and discharge is 2m. If discharge is 0.01m3/s, find the horsepower needed to pump the water for 80% pump efficiency. ANSWER: 8.15 hp
Air @ 68°C is pumped through a pipe of internal d = 6.4in: If the vol flowrate is set to 6.2 ft3/min, is the flow laminar or turbulent? assume P is atmospheric.
The San Francisquito plant no. 1 is supplied by 3 steel-lined penstocks each 80 inches in diameter that carries a combined volumetric flow rate of 712 ft3/s. Assuming water at 80°F find a)Head loss (in feet) due to viscous effect . Include both major and minor losses. b)Your estimate of the power generation potential in MW.
A 152.4 mm, Schedule 40 pipe line 91.4 m long conveys 3028 l/min of cold water from a pump to a point of discharge 24.4 m higher than the pump. There are four 90° elbow in the line. Find the pumps dynamic discharge head. Use Table of Equivalent Length of Straight Pipe (see image). Please help. Thank you :)
a pumping station working with a pump head of 25m. the output power of the motor for that pump is 16kw. identify the pump efficiency if the sewarge discharge velocity is 0.27 m/s and the pipe diameter is 250 mm
A 75mm diameter orifice discharges 26 L/s of liquid under a constant total producing head of 3m. The diameter of the jet of the vena contracta was measured using a digital caliper and it reads 66.5mm. Calculate the coefficient of velocity.
The following system is fed by a centrifugal pump. The piping is constructed from smooth plastic of OD 55 mm, wall thickness 2.5 mm. The minor losses for the system prior to the pump are given by KL = 12.0. The system curves for this pump are attached. If the flowrate is reduced to 1.4 m3/hr, and the upstream head requirement were 17 m, what would the electrical power requirement of the pump be?
For the siphon in Fig. 6.26, calculate the distance X re-quired to obtain a volume flow rate of 7.1 X 10-3m³/s.
A sharp edged orifice will be required to produce a discharge of 35 liters/sec of water under a head of 3m. Find the required diameter, when C = 0.595