QUESTION 22 A hydraulio metal stamping machine must produce 12.000 parts per 8 hour shift The force versus position curve for a typical part production is provided below. How much power must be supplied to the machine if it is known that only 73% of the supplied power goes directly into stamping parts? (The rest is in retracting the tooling and wasted as heat) Answer in wats Stamping Operation Actuator Force Vs Position Data 70 60 50 40 30 20 10 10 20 30 40 Actuator Extension (mm) Actautor Force (kN)

QUESTION 22 A hydraulio metal stamping machine must produce 12.000 parts per 8 hour shift The force versus position curve for a typical part production is provided below. How much power must be supplied to the machine if it is known that only 73% of the supplied power goes directly into stamping parts? (The rest is in retracting the tooling and wasted as heat) Answer in wats Stamping Operation Actuator Force Vs Position Data 70 60 50 40 30 20 10 10 20 30 40 Actuator Extension (mm) Actautor Force (kN)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(USCS units) A turning operation is performed using a rake angle of 15°. Cutting speed = 200 ft/min, feed= 0.012 in/rev, and depth of cut = 0.100 in. The chip thickness ratio measured after the cut = 0.48. Determine (a) chip thickness after the cut, (b) shear angle, (c) friction angle, (d) coefficient of friction, and (e) shear strain (USCS units) The turning operation in the previous problem involves a work material whose shear strength = 52,000 lb/in2. Based on your answers to the previous problem, compute (a) shear force, (b) cutting force, (c) thrust force, and (d) friction force.
A student is performing a turning operation with a workpiece with an initial diameter of 40 mm to produce a 30 mm diameter rod that is 100 mm long. The lathe power is 20 kW and is operating on 85% mechanical efficiency. If the student set the cutting speed to 0.5 m/min and the cutting tool is set to have a rake angle of 5 degrees: a.) What material can we choose for the rod is the coefficient of friction is 0.5? b.) If we select 4130 normalized heat-treated steel for the rod, and coefficient of friction is 0.5, what will the maximum depth of cut we can achieve?
Sheet Forming Processes; V-Bending of Sheets is more expensive than Edge Bending. (T or F)In Metal Forming Processes there are 2 Basic Categories; Bulk Deformation Sheet Metalworking (T or F)In Sheet Metalworking there are 3 types of processes used; Bending Drawing Cutting (T or F)An Advantage of Hot Rolling is the process produces a final product with Small Tolerances (T or F)Direct Extrusion produces Hollow or Semi-Hollow types of Cross-Sections. (T or F)Designing a metal sheet product in the elastic zone of the Stress-Strain curve gives a longer life cycle for the products service (T or F)In the Bulk Deformation, Drawing Process, there is Tension Residual Strain. (T or F)Hot Rolling metal prevents residual stresses from building up in the made product (T or F)
21 Forging process is suitable for mass production. Select one: True False
Please typing answer only IENG 302 - Manufacturing Processes: We are reducing the diameter of a 95.8 mm cylinder to 30.04 mm using 7 roughing passes and 3 finishing passes. The finishing operations use a depth of cut of 1.51 mm. The roughing operations are performed with a feed rate of 9.61 mm/s and the finishing operation is performed with a feed rate of 11.31 mm/s. a) What is the depth of cut for a roughing pass? b) What is the rate of material removal (mm^3/s) for the third roughing pass? c) What is the rate of material removal (mm^3/s) for the final finishing pass? d) What is the average rate of material removal (mm^3/s) for the roughing operations?
A compound die will be used to blank and punch a large rectangle (90x150mm blank dimensions) out of 6061ST aluminum alloy sheet stock 3.5 mm thick. The diameter of inside hole is 25 mm. The aluminum sheet metal has a tensile strength 310 MPa. Determine the minimum tonnage press (force) to perform the blanking and punching operation (1) assume that blanking and punching occur simultaneously and (2) assume that punching occurs first, then blanking, Take: Ac-0.06
In a lathe machine, the maximum torque transmitted by a shaft exceeds the mean torque by 11 %. A power of 3 kW has to be transmitted to another shaft at a speed of 625 rpm. What should be the value of Maximum torque ? The maximum torque transmitted in N-m, Answer
Standard time & work sampling The following data resulted from a time study made on a horizontal milling machine: Mean manual effort time per cycle: 4.62 min Mean cutting time (power feed): 3.74 min Mean performance rating: 115 percent Machine allowance (power feed): 10 percent Fatigue allowance: 15 percent questions: 1.) What is the Basic Time for the manual effort? 2.) What is the Standard Time for the manual effort? 3.) What is the Standard Time for the machine?
Thank you in advance If you have a Bulk Deformation Process in Metalworking with a product in the Rolling Process that has the following information: Original Thickness = 0.85” , Original Width = 12” , Entering Velocity = 28”/min, Final Thickness = 0.66, Exiting Velocity (in/min) = 30 (use 4 digits for answers) Final Width = _____________ in.
A cylindrical ingot with D0 = 50 mm and h0 = 40 mm is cold forged using an open die.The final height is 20 mm. The coefficient of form / friction between the die and the workpiece isconsider Kf = 1.10.The material from which the ingot is made has the following characteristics:K = 600 MPa and η = 0.12.Determine the force (F) on the operation:a) Force required at the moment of reaching the yield point (ℇ = 0.002)b) Force required when you have a height of h = 30 mmc) Force required when there is a final height of h = 20 mmd) Construct the graphs: Force vs Δh and effort vs Δh
Manufacturer process A compound die will be used to blank and punch a large rectangle (90x150mm blank dimensions) out of 6061ST aluminum alloy sheet stock 3.5 mm thick. The diameter of inside hole is 25 mm. The aluminum sheet metal has a tensile strength = 310 MPa. Determine the minimum tonnage press (force) to perform the blanking and punching operation (1) assume that blanking and punching occur simultaneously and (2) assume that punching occurs first, then blanking. Take: Ac=0.06
The following data were obtained from a time study performed on a horizontal milling machine: Average manual effort time per cycle: 4.62 minutes. Average cutting time (electric feed): 3.74 minutes. Average performance rating: 115%. Backlash due to machine (power supply): 10%. Slack due to fatigue: 15%. What is the standard time for the operation?