Q 3 maritime standardsO National consensus standardsQUESTION 3A fire of ordinary combustibles should be put out with an extinguisher labeled with aBlue circle (Type C)Green Triangle (Type A)Red square (Type B)O Yellow star (Type D)QUESTION 4Which of the following statements are false?Meters use electromagnetismO Relays open and close switches

When there is an abnormality in the system, It is sensed by the relay, and based on their trip limit…

QUESTION 3 A fire of ordinary combustibles should be put out with an extinguisher labeled with a O Blue circle (Type C) O Green Triangle (Type A) O Red square (Type B) O Yellow star (Type D) QUESTION 4 Which of the following statements are false? Meters use electromagnetism Relays open and close switches

QUESTION 3 A fire of ordinary combustibles should be put out with an extinguisher labeled with a O Blue circle (Type C) O Green Triangle (Type A) O Red square (Type B) O Yellow star (Type D) QUESTION 4 Which of the following statements are false? Meters use electromagnetism Relays open and close switches

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter1: Electrical Safety

Section: Chapter Questions

Problem 7RQ: Which of the following is the standard by which electrical installations are measured in the United...

See similar textbooks

Similar questions

Indicate the allowable ampacity of the following Type THHN (copper) conductors. Refer to Table 310.15(B)(16). a. 14 AWG __________ amperes b. 12 AWG __________ amperes c. 10 AWG __________ amperes d. 8 AWG __________ amperes e. 6 AWG __________ amperes f. 4 AWG __________ amperes
Electric heating cable embedded in plaster, or sandwiched between layers of dry wall, creates heat. Therefore, any nonmetallic-sheathed cable run above these ceilings and buried in insulation must have its current-carrying capacity derated according to the (40C) (50C) (60C) correction factors found in Table 310.15(B)(2)(a) in the NEC. (Circle the correct answer.)
Which of the following is the best conductor? a. wood b. thermoplastic c. copper d. cast iron
What is the name of an appliance that is used to remove moisture? a. humidifier b. dehumidifier c. air conditioner d. both a and c
A snap switch with integral nonmetallic enclosure complying with NEC 300.15(E) is required to be connected to an equipment grounding conductor. A. True B. False
11. An electrical device would also fall into the classification of an electric(al)A. motor.B. load.C. component.D. fitting I'm not sure if it's the letter A or C, could you help me with the correct answer.
1.a. Section 300.15(C) requires a fitting to be installed on each end of a conduit or tubing being used toprovide support or protection to protect the cable fromA. hazardous vapors.B. direct sunlight.C. abrasion.D. extreme heat or cold.1.b. Typically, a/an _______ is a better electrode than a ground rod because it provides a greater surface areafrom which the electrons can be dissipated.A. continuous grounding conductorB. clamp-on ground resistance meterC. rebarD. OCPD
Don’t Copy Others work. Here is only one question. Don't say multiple question. If you are not able to provide complete question answer kindly skip the question. Sub: Optoelectronic Dept: EEE
7.a. What size diameter is a T-12 fluorescent lamp?A. 6 inchesB. ½ inchC. 3 inchesD. 1½ inches7.b. Which of the following is not a brand name of a high-pressure sodium lamp?A. Multi Vapor.B. Ceramalux"C. Lucalox.D. Lumalux.7.c. Which of the following is not a characteristic of an HID arc tube?A. Contains a gasB. Usually made of copperC. Operates at very high pressureD. Operates at very high temperatures
1. One type of lighting controls technology that does not work well with bollards on pedestrian walkways is: a. Time Based controls b. Louver controls c. Occupancy Sensor controls d. None of the above 2. Three types of high-intensity discharge (HID) lighting technologies are: a. Mercury Vapor, High Pressure Sodium, and Metal Halide b. Tubular Fluorescent, High Pressure Sodium, and Metal Halide c. Metal Halide, High Pressure Sodium, and Tubular Fluorescent d. None of the above 3. Some newer models of HID and Fluorescent light sources can a have rated life of: a. 10,000 - 20,000 hours b. 25,000 - 50,000 hours c. 50,000 to 100,000+ hours d. None of the above 4. Which of the following characteristics apply to Induction Lighting? a. A physically large light source b. A limited optical designs c. A limited range of light d. All of the above 5. What technology advancement enables a light source to have longer life? a. Elimination of electrodes b. Elimination of…
________ covers selection of time-delay fuses for motor-overload protection. A. NEC 430.32(A)(1)B. Table 430.248C. NEC 430.247D. NEC 400.4
Answer the questions quecly please Electrical machines