QUESTION 3. A vertical shear force of V-50 kN is applied on the cross-sections shown in Figure 3. If the thickness of each section is 4 mm, a. Determine the shear flow distribution on the cross section and represent this distribution with arrows and by drawing a shear flow diagram b. Define the location of the shear center for the cross-sections shown in the figure. ITL

QUESTION 3. A vertical shear force of V-50 kN is applied on the cross-sections shown in Figure 3. If the thickness of each section is 4 mm, a. Determine the shear flow distribution on the cross section and represent this distribution with arrows and by drawing a shear flow diagram b. Define the location of the shear center for the cross-sections shown in the figure. ITL

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

show step by step solution and explain why the Q for the bottom area below the N.A is used to calculate the shear flow
1. A Vertical semicircular area of radius r = 100cm is submerged and has its diameter in a liquid surface. Determine (a) total force acting on one side and (b) its location from the liquid surface.2. Determine (a) the magnitude and (b) location of the total hydrostatic force acting on the 2m x 4m gate shown in Figure.
gage pressure at point 1 = 275 kPa velocity = 3 meters/sec *Neglect friction* Given the figure, determine the total longitudinal thrust applied on the horizontal pipe.
The 280 kg, 6m wide rectangular gate shown is hinged at B and leans against the floor at A making an angle of 45deg with the horizontal. The gate is to be opened from its lower edge by applying a normal force P at its center. a. Determine the magnitude of the hydraulic force acting on the gate using the hydrostatic panel equation. Express your answer in kN. b. Determing the minimun force P required to open the seawater gate. Express your answer in kN.
Problem 4 A square gate (2m on each side) is submerged vertically in water such that the upper edge of the gateis at a depth of 0.5 m from the watersurface. Draw the figure and find the hydrostatic force and the location of the center of pressure.
For the cross-section shown in figure. Torque,T= 150 kNmm. q1, q2 and q3 are the shearflows in cell I, II and cell III respectively. Here thickness of different sections are:t12 = t25=t56= 0.03t23 = t34 = t45 =0.04t61 = 0.035curve 61, t =0.025G = 55000 MPaDraw the shear flows distribution diagram for the given section
The tank shown in the figure is 3 m wide into the paper. Neglect atmospheric pressure. Use ?????? = 9.79 kN/m³. Determine the following: A. vertical component of the total hydrostatic force on the quarter circle panel AB in kN B. Resultant hydrostatic force acting on the quarter circle panel AB in kN C. Angle that the resultant hydrostatic force make with the horizontal in degrees.
H1. A rectangular beam of 100mm wide and 150mm deep is subjected to Shear force of 30KN, Determine ratio of Maximum shear stress to Average shear stress. Derive the equation which is used to find out the shear stress.
Calculate the shear stress for the illustrated flow to 2 significant figures(dyn/cm2 ; do not use scientific notation).
11. A rectangular channel with width = 10 meters and depth = 3 meters has a flow slope of 0.001 and roughness n = 0.025. The flow rate is 80 m3/s. Determine the shear stress on the channel in Pascals.
Determine the vertical distance of the center of gravity of the curved gate from the water surface shown in the figure. The curved gate is 5.7 m long. The values of the vertical component (Fv) and the resultant force. (F) acting on the gate are 300 kN and 400 kN asap
A. A concrete dam retaining water is show in the figure. If the specific weight of concrete is 23.5 KN/m^3. What is the total hydrostatic force? Find the resultant force. Find the factor of the safety against sliding if the coefficient of friction is 0.50. What is the factor of safety against overturning? Find the location of the resultant. Find the maximum intensity pressure. Determine the minimum intensity pressure.