Question 3.3 A square lamina is immersed in water with one of the diagonals vertical as shown in given figure. Calculate the force on one side and the location of the centre of pressure. 0.6 m a G 6. a = 0.6 m Figure I

Question 3.3 A square lamina is immersed in water with one of the diagonals vertical as shown in given figure. Calculate the force on one side and the location of the centre of pressure. 0.6 m a G 6. a = 0.6 m Figure I

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Use the manning's equation above to find the streamflow rate (Q) under the following conditions: a.…

A: From Manning's Equation Q=knAR23S12 K= 1 m/s For Earth winding and vegetation n= 0.030 Top width…

Q: determine the shear force in beam at point B

Q: A vertical triangular gate with a horizontal top base that is 3m wide is 6m high. It is submerged in…

Q: average velocity of 0.9 m/s shown in Figure 4. The dynamic viscosity of water µ = 1.307 × 10-3…

A: diameter of pipe, d = 0.0012 m Length, L = 17 m Velocity in pipe, v = 0.9 m/s

Q: Calculate the pump capacity

A: Given, Pipe length (L) = 73 m Pump efficiency = 75% D1 = 2 in or 0.05 m D2 = 1.5 in or 0.0375 m

Q: 2. A 640.kg car encounters a hump that has a circular shape with smooth transitions at either end.…

A: Normal force The normal force is the force exerted by surfaces to keep solid objects from passing…

Q: Determine the moment of inertia with respect to x-axis. b- 159 mm, d - 216 mm y t- 37.4 mm. EC d

A: Given: b=159 mm, d=216 mm t=37.4 mm

Q: Bearing Angle Traverse Given the tabulated measurement of the closed traverse as shown. Determine…

Q: On an urban road, the free mean speed was measured as 70 kmph and the average spacing between the…

Q: Calculate ALL the bar forces of the given truss below: 35 kN 4m 84 kN 4m t3m

Q: High flakiness index of aggregate will cause high tendency of aggregate breaking under the action of…

A: Flakiness index of aggregate is the percentage by weight of aggregate particles of least dimension…

Q: It is safe to assume that the one-year rainfall totals fit a normal, log-normal and log-Pearson…

A: Yes , one year rainfall fits to normal ,log normal , log Pearson distribution We can assume…

Q: Pipe 1, 2 and 3 having diameter of 150mm, 200mm and 250mm and leading from resorvoir A,B and C…

A: To Determine Discharge in pipe 1, Q1

Q: ght is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the…

A: Given:- W=110kN temperature rises by 20∘C To find:- the stress in each rod

Q: D, 3 Use the diagram shown above. Given • D= 10 ft • D2= 7 ft • D3=4 ft • W - 500 #/ft Solve for the…

A: Figure is as shown

Q: determine the support reaction in beam at point

Q: In the figure show, a long uniform rod of uniform cross-section is partially submerged in 3 fluid…

Q: Two steel columns P (Length L end yield strength = 250 MPa) and a (length 2L and yield strength =…

Q: storm occurred in two similar watersheds, A and B, both having an area of 700 hectares. A is long…

A: Watershed area and peak discharge. The value of peak discharge is greatly dependent upon the shape…

Q: .: using the British Method, design a Concrete mix for a blinding with a specified characteristic…

Q: Illustrate the Influence Line and calculate the maximum positive live shear at point C in kN…

A: We will draw ILD for shear at C.

Q: The test results of a soil sample are given below. Percentage finer than 4.75 mm = 55 Percentage…

Q: Show the complete solution. Solve for the x and y components of each force acting on the plate of…

Q: An axially loaded square tied column is to be designed for the following service loads. DL = 1800 kN…

Q: A reinforced concrete beam has a width of 250 mm and a total depth of 450mm. It carries an ultimate…

Q: Calculate the slope at C using ONE of these methods: double integration method, area- determine the…

Q: 3. (a) For the beam shown in Figure Q3a, E is constant throughout. Using the moment distribution…

Q: er jam condition as 7.0 m. The speed-f given by: k and q = Uxk k. U = Ug1- %3D sf where, U =…

Q: 4 kum 16 KN 6m 4m 2m

Q: 2. Lacquer paints A. are generally applied on structural steel are less durable as compared to…

Q: b- 159 mm, d - 216 mm y t- 37.4 mm. y EC d b -

Q: Asphalt mix with VFB 76% is not acceptable to be used for wearing course layer. True O False

Q: In an unconfined compression test a sample of clay 10o mm long and 50 mm in diameter fails under a…

Q: Which of the following statements are True about the binder course layer? O The layer is cambered O…

A: Among the given statements, Second statement is true. Since the binder course is laid to transfer…

Q: I. Problem Solving: Answer what is being required. Show you complete solution. 1. Compute the…

Q: A city discharges 25 MLD domestic sewage into a stream whose average flow is 185 MLD. The velocity…

A: While designing the sewerage system where two streams are mixing with each other from upstream to…

Q: A cohesive soil sample is subjected to an unconfined compression test

Q: DRAW THE SHEAR AND MOMENT DIAGRAMS FOR EACH MEMBER OF THE FRAME.THE MEMBERS ARE PIN CONNECTED AT A,…

Q: Three bars, AB, AC, and AD, are pinned together to support a load P = 20 kN as shown in Fig. P-256.…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: Discus the sequence of the different stages of prestressing a beam, in 10 sentences or less. Provide…

Q: State the five (5) major steps used in engineering design and problem solving process.

A: The five major steps in engineering design and problem solving process are as: Defining the…

Q: An auto A is moving at 6m/s and accelerating at 1.5m/s^2 to overtake an auto B which is 115.2m…

Q: Answer the question based on the data given; SG bulk of the asphalt, 2.332 Theoretical maximum…

A: We will use formula for air voids.

Q: P B 5m 5 m 5 m

Q: In the work-energy theorem equation, may I ask why the gravitational potential energy (mgh) is no…

A: Gravitational potential energy is the energy stored in an object as a result of it's vertical…

Q: Bearing Angle Traverse Given the tabulated measurement of the closed traverse as shown. Determine…

A: For closed traverse Sum of latitdue = 0 Sum of departure = 0 Let's assume Length of BC = L1…

Q: A steel column W300 x 203 kg/m section is used as to support an aial load. A=25740mm^2 Tw =…

Q: 2. Lacquer paints А. are generally applied on structural steel are less durable as compared to…

A: Correct answer (E) all of above Explanation:- A lacquer paint is clear coating that, when dried,…

Q: The orifice in the figure shown is 50mm in diameter and is sharp-edge with Cc= 0.63, and Cv = 0.97.…

A: Area of Jet is given by AJ=CCAOπ4DJ2=0.63π4Do2DJ=0.6350DJ=39.69mm

Q: In the accompanying sketch, A, B, and C are three known control stations and P is the position of…

A: *Multiple Sub- parts* As per our company guidelines we are supposed to answer ?️only first 3️⃣…

Concept explainers

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

(a) Determine all reactions and bar forces pro-duced by the applied load in Figure P9.33. (b) If supportB settles 1 in. and support C settles 0.5 in. while the loadacts, recompute the reactions and bar forces. For all barsthe area = 2 in.2and E = 30,000 kips/in.2
The force of 500 N is the resultant of the forces P and 250 N acting as shown in the figure. Compute the following: (a)the angle that the 500 N makes with the horizontal, (b)the value of a and (c) the value of P.
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C Assume I = 800 x 106 mm4 and E = 70,000 MPa. W1 (kN/m) = 25 F (kN) = 50 S (mm) = 15 If there is a settlement of S at the support C, solve the following: 1. Slope at B, in radians 2. Slope at C, in radians 3. Reaction at A, RA in kN 4. Moment at A, MA in kN-m 5. Reaction at D, RD in kN 6. Moment at D, MD in kN-m
Analyze the structure in Figure P10.17. In addition to the applied load, support A rotates clockwise by 0.005 rad. Also E = 200 GPa and I = 25 × 106 mm4 for all members.
The frame shown in the figure is supported by a hinge at A and a roller at E. Compute the vertical components of the hinge forces at C as they act upon member AC in kN. P = 28 kN and x = 3.3 m.
T (Shear force) and M (Bending) for the system whose loading condition is given in Figure 1.Draw the moment diagrams. Calculate the deflection (vertical displacement) at point B in mm using Castigliano's Theorem. The beam bending stiffness (EI) is constant along the bar and its value is 50 000 kNm2. q=1,4(kN/m) a=8(m) El=50000(kNm2)
Compute vertical displacement of E if: 100 kips acts dowmward at A A unit force acts down at E
A rectangular beam is supported at both ends. It carries two concentrated load of 110kN, a clockwise moment of 110kN-m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 60GPa. Solve the following if the reaction at point B is 328.90256410256kN, upward. BEAM DIMENSION: Width = 190mm , Height = 390mm NOTE: b = 4.8m ; Determine the deflection at midspan
Question: Calculate the vertical reaction force at G and the vertical reaction force at A.
Calculate the vertical reaction at support B. When sketching FBD, assume the positive direction of all reactions in the positive direction of y axis. Enter your answer in kN to two decimal places.
Calculate the vertical support reaction in support A. When sketching FBD, set the positive directions of both reactions in the positive direction of y axis. Enter your answer in kN to three decimal places.
The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical forces P = 400 kN and P = 360 kN acting at points A and D, respectively (see figure). Bars BE and CF are made of steel (E = 200 GPa) and have cross-sectional areas ABE = 11,100 mm and Acr = 9,280 mm. The distances between various points on the bars are shown in the figure. Determine the vertical displacements & and dp of points A and D, respectively.