Question 4 For the State Machine shown below, if two JK flip-flops are used. The input signal is A, and the output is F. For the equations below, which one is correct? 00- 01- 11 10
Q: Draw a circuit that represents the following equation "A•B•C" gate using only 2-imput AND gates.
A:
Q: Two tests were performed on a 4-kVA , 200/400 V transformer to predetermine its efficiency. Open…
A:
Q: The network shown in Figure 2 contains two voltage sources, V, = 30 Z0° and V2 = 2020°. Using mesh…
A: In this question, We need to determine the power in network resistance We know power P= I2 R Where…
Q: The network shown in Figure 2 contains two voltage sources, V, = 30Z0° and V2 = 2020°. Using mesh…
A: In this question, Find the power in the resistor We know Power P= I2 R Watt
Q: 3. In a bridge-type full-wave rectifier with capacitor filter produces an output voltage with a peak…
A: Given: Peak voltage, Vp=48 V Load, RL=500 Ω Ripple factor, γ=8% To find: Value of capacitor
Q: Using definition of CTFT, find X(2) for the following x(t). Also plot |X(N)| and /X(2) a. r(t) =…
A: According to the question, we need to find CTFT for the following functions
Q: Given a variable resistor R of unknown resistance connected in parallel with an inductive reactance…
A:
Q: For a citizens band receiver Lusing high side injection with an RF carrier of 6 11 MHz and a 27.09…
A:
Q: Calculate the voltage across the inductor in phasor form
A:
Q: 30. Sketch vo for the network of Fig. 2.174 and determine the dc voltage available. + 100 V Ideal…
A:
Q: A resistor of 50 ohms, a 200mH inductor, and a 1.5 x 10-4 F capacitor are connected in parallel to a…
A:
Q: capacior with area the distance between the, tuio filled by twe dielectrii materiàl wit interface…
A: The parallel plate capacitor with the given specifications is shown below: The above diagram shows…
Q: If two coils are close enough to have a mutual inductance of 0.2 µH and the coils have inductances…
A: In this question we need to find a coefficient of coupling .
Q: How long does it take for the conductors to reach the threshold temperature in a short circuit?…
A: The maximum operating temperature for the given conductor is, T1=70 oC. The cross-sectional area of…
Q: A 200 kVA, 60 Hz, 4600/230 volt transformer has the following characteristics: R;=2.25 Q R,=0.005 N…
A:
Q: In the given circuit above, work out the following: 1) Determine the: a) dc transistor terminal…
A: The circuit is as shown below,
Q: Find the operating region of the MOSFET and VD when ID = 0.2A and R=5 ohm? +1.8 V R o VD a. Triode,…
A:
Q: An input voltage of 2 Vrms (measured from base to ground) is applied to the circuit of the figure.…
A: The following circuit diagram is given:
Q: An engineer intends to determine all of the different currents flowing in the circuit shown below. R…
A: Given: Vs=16V, R1=110Ω, R2=180Ω, R3=91Ω, R4=470Ω, R5=270Ω Circuit diagram:
Q: Implement f(a,b,c,d) = Σ m (1,2,3,5,9,10,11,15) using minimal gates and appropriate: (a) Decoders…
A: Brief description : In digital circuits we have different type of elements which are helpful in the…
Q: A resistor of 50 ohms, a 200mH inductor, and a 1.5 x 10-4 F capacitor is connected in parallel to a…
A: The solution is given below
Q: 6.54 For the transistor shown in Fig. P6.54, assume a 2l and vgE = 0.5 V at the edge of conduction.…
A:
Q: During the positive input cycle shown, the conduction path is through diodes a. Di and D2 b. Dz and…
A:
Q: A Half-Wave rectifier with a capacitor filter (capacitance is 4700 µF ) supplies to a load an…
A:
Q: Explain this graph
A: The given graph is the frequency response of the system. The frequency response graph gives us…
Q: What is the rated full-load current of a ¾-horsepower, 208-volt single-phase motor
A: The solution is given below
Q: A clothes dryer rated at 6kW is connected to a 120/240 V, single-phase, three-wir individual branch…
A: In this question, We need to choose the correct options What is load current if total load 6kW…
Q: Which of the following are considered an issue with wind or solar power? a) It is not always…
A: The answer is option d) all of the above. Let's get to each option one by one.
Q: What are the maximum and minimum frequencies of a 16-MHz crystal with a stability of 200 ppm? The…
A:
Q: When rated voltage at rated frequency is applied to a single phase transformer the hysteresis and…
A: Given, Hysteresis loss, Ph1=420 W Eddy current loss, Pe1=150 W Voltage in increased by 10%, V2=1.1…
Q: Determine Rout (in kl2) for the figure. Ipss= 10 mA Vp=-4 V 4.7 kM 10 V o M Mw0-2.5 V 2 ΜΩ
A: We need to find out output impedance of given circuit
Q: Provide the nature of the response (undamped, overdamped, undamped, critically damped) of the output…
A:
Q: 103 ... For the circuit shown in Figure 25-72, switch S has been open for a long time. At timet-0…
A: The solution is given below
Q: Find the Transfer function of the system using block diagram reduction.
A:
Q: Using node voltage network analysis, find the ratio Vo/Vi in network shown of Figure 1, given Vo as…
A:
Q: During a lighting discharge, 30 C of charge move through a potential difference of 1.0 x 108 v in…
A: “Since you have asked multiple question, we will solve the first question for you. If you want any…
Q: Sketch the transfer curve for an n-channel depletion type MOSFET with IDSS=14 mA and Vp = -5 V
A:
Q: 7. A DC motor produces 1500 W of power at a speed of 1600 rpm. What value below is most near the…
A: The solution is given below
Q: For the cascode amplifier of Fig. 4.143 detemine a. the base and collector currents of each…
A: Cascade Amplifier: A cascaded amplifier is just a collection of amplifiers combined into a single…
Q: What is the importance of electrical wiring symbols and diagrams used in the electrical plan?
A: A circuit diagram or wiring diagram uses various symbols to represent parts of a circuit. A circuit…
Q: Which of the following s-plane represents the graph for the system having a transfer function G(s) =…
A: In this question, We need to determine the representation in the s plane. If transfer function is…
Q: Given that αdc =0.980, determine the corresponding value of βdc. b. Given βdc =120, determine the…
A:
Q: Solve for the transfer function using mason rule
A: In this question we need to find a transfer function of the given system by using mason rule
Q: Cubes 1 and 2 electrostatically attract each other, and Cubes 1 and 3 electrostatically repel each…
A:
Q: in matlab What are the possible ways to fix the error in the following model? Interpreted MATLAB Fan…
A: Scope block in matlab is used to see the simulation results The display block in matlab is used to…
Q: 12Ω R3 93 E 30 V R2 60 60 V E2
A: The point related to the superposition theorem: To apply superposition, it is essential that if…
Q: Which of the following has a characteristic to operate in high voltages and can be transmitted over…
A: In this question we need to choose a correct option.
Q: 1. Suppose g(t) = x(t) • cos (t) and the Fourier transform of g(t) is G(jw) depicted as below. G(jw)…
A:
Q: A 5 kHz audio tone is used to modulate a 50 MHz carrier causing a frequency deviation of 20 kHz.…
A: Please find the detailed solution in below images
Q: 13. A permanent magnet motor has the ability to generate to a variety of magnetic fields True False
A: A permanent magnet motor is a type of motor that uses magnetic in the field along with the windings.
Step by step
Solved in 2 steps with 2 images
- Perform example number 2: Create a state diagram for the finite- state machine with the state table shown in Table 2. Make a circuit diagram use D flip flop to represent the circuit. Looking forward to your kind response tutor :)A coin-operated cold drink dispenser will provide cold drink (D) under the following conditions: The correct coin (C) is inserted AND A paper cup is in position (P) AND The selector is set t Orange (O) OR Sprite (S) OR Lemonade (L) Write the Boolean expression for the output of the dispenser. Represent the operation of the dispenser in logic circuit 4 get a logic circuit to mimic aorporate checquing system for operatore of a compnnyDesign circuit that has an input w and an output z. The circuit is a sequence detector that produces z = 1 when the previous two values of w were 00 or 11; otherwise z = 0. Use W=0101100010101110101011100010 a) For this problem design the circuit using JK flipflops, draw the state diagram, true table, logic circuit.
- B) A coin-operated cold drink dispenser will provide cold drink (D) under the following conditions: The correct coin (C) is inserted AND A paper cup is in position (P) AND The selector is set t Orange (O) OR Sprite (S) OR Lemonade (L) Write the Boolean expression for the output of the dispenser. Represent the operation of the dispenser in logic circuit 4 get a logic circuit to mimic aorporate checquing system for operatore of a compnnyFlip flop input and output equations for a sequential circuit with 3 flip flops (A, B and C), 2inputs (X and Y) and 1 output (Z) are as follows. Create a state table for the circuit anddraw the state diagram of the circuit. State whether the circuit is a Mealy or Moore circuitand explain why? A(t+1) = A’Y + BX’B(t+1) = AX’ + B’YC(t+1) = AZ = A’B + X’YDesign a circuit called half adder (HA) which adds two 1-bit numbers, a,b and produces 2-bit output, c. a. Draw the truth table of the circuit.b. Find the Boolean functions of each bit of the output.c. Optimize the Boolean functions.d. Draw the logic diagram of the optimized circuits.e. Write the VHDL code of the logic diagrams by using “Dataflow modeling” method f. Simulate the circuits that you have designed in 1.e. Prepare a simulation waveform for you report.g. Produce the RTL schematic for the circuit that you have designed in 1.e.
- A sequential circuit with two D flip-flops D1 and D2, two inputs x and y, and one output z is specified by the following excitation and output equations:D1 = xy¯ + xQ2D2 = xQ1 + xQ¯2z = Q1(a) Draw the logic diagram of the circuit(b) List the state table for the circuit(c) Draw the corresponding state diagramThe car will not start (S = 0) whenever the following conditions arises: (I) The key is not inignition (A), or (II) the front doors (B) or back doors(C) are not locked properly, or (III) the seatbelt of driver is not locked properly (D). The key in ignition, locked doors, and locked seat beltproduces the output HIGH. Obtain the truth table and minimize the Boolean function usingBoolean algebra. Implement the logic circuit using the suitable logic gates.A sequential circuit with two D flip-flops A and B, two inputs, x and y ; and one output zis specified by the following next-state and output equations A(t + 1) = xy’+ A’y‘ B(t + 1) = xB+ B‘+ xB’ z = A‘B (a) Draw the logic diagram of the circuit. (b) Draw the corresponding state diagram.
- Course: Computer Engineering Subject: Logic Circuit and Switch Theory Find a function to detect an error in the representation of a decimal digit in BCD. In other words, write an equation with value 1 when the inputs are any one of the six unused bit combinations in the BCD code, and value 0 otherwise. Course: Computer Engineering Subject: Logic Circuit and Switch TheoryAn electronic system will only operate if three switches A, B and C are correctly set. An output signal (X = 1) will occur if A and B are both in the ON position or if A is in the OFF position and B and C are both in the ON position. Design a logic circuit to represent the above situation and draw the truth table and Karnaugh diagramAlert dont submit AI generated answer. Question 4:Using JK flip-flops, design a sequential circuit that uses an external input x to trigger acounter that displays odd numbers between decimal numbers 0 and 7. The circuit countswhen x = 0 but remains in the same state when x = 1. show all steps and how the circuit would look