6 Question 4:ItemWeightArmBasic Empty Weight1,923 Ibs53 inchesFront seat2 passengers @ 17O Ibs each45 inchesRear seat2 passenger @ 170 Ibs59 inchesBaggage30 Ibs70 inchesFuel35 gallons @6 lbs/gal56 inchesQ4A: What is the weight of the loaded aircraft?Q4B: What is the CG of the loaded aircraft?.Use the following data to answer questions 2C and 2D.Maximum weight: 2,840 lbs• CG range: +50 to +56.2NO)Q4C: Is the airplane under maximum weight? (YESNO)Q4D: Is the airplane within CG range? (YESExplain steps clearly

4A) The total loaded weight of the aircraft will be the sum of weight of passengers, baggage and…

Question 4: Item Weight Arm Basic Empty Weight 1,923 lbs 53 inches Front seat 2 passengers @ 170 Ibs each 45 inches Rear seat 2 passenger e 170 Ibs 59 inches Baggage 30 Ibs 70 inches Fuel 35 gallons @6 lbs/gal 56 inches Q4A: What is the weight of the loaded aircraft? Q48: What is the CG of the loaded aircraft? Use the following data to answer questions 2C and 20. • Maximum weight: 2,840 lbs • CG range: +50 to +56.2 NO) Q4C: Is the airplane under maximum weight? (YES NO) Q4D: Is the airplane within CG range? (VES

Question 4: Item Weight Arm Basic Empty Weight 1,923 lbs 53 inches Front seat 2 passengers @ 170 Ibs each 45 inches Rear seat 2 passenger e 170 Ibs 59 inches Baggage 30 Ibs 70 inches Fuel 35 gallons @6 lbs/gal 56 inches Q4A: What is the weight of the loaded aircraft? Q48: What is the CG of the loaded aircraft? Use the following data to answer questions 2C and 20. • Maximum weight: 2,840 lbs • CG range: +50 to +56.2 NO) Q4C: Is the airplane under maximum weight? (YES NO) Q4D: Is the airplane within CG range? (VES

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.22P: 1.22 In order to prevent frostbite to skiers on chair lifts, the weather report at most ski areas...

See similar textbooks

Similar questions

1.22 In order to prevent frostbite to skiers on chair lifts, the weather report at most ski areas gives both an air temperature and the wind-chill temperature. The air temperature is measured with a thermometer that is not affected by the wind. However, the rate of heat loss from the skier increases with wind velocity, and the wind-chill temperature is the temperature that would result in the same rate of heat loss in still air as occurs at the measured air temperature with the existing wind. Suppose that the inner temperature of a 3-mm-thick layer of skin with a thermal conductivity of 0.35 W/m K is and the air temperature is . Under calm ambient conditions the heat transfer coefficient at the outer skin surface is about (see Table 1.4), but in a 40-mph wind it increases to . (a) If frostbite occurs when the skin temperature drops to about , do you advise the skier to wear a face mask? (b) What is the skin temperature drop due to the wind?
The friction force F on a smooth sphere falling in water depends on the sphere speed V, the sphere density ρ_s and diameter D_s, the density ρ and dynamic viscosity μ of the water, gravitational acceleration g. Choose the correct repeating variables. sphere diameter, dynamic viscosity, gravitational acceleration density, gravitational acceleration, dynamic viscosity friction force, gravitational acceleration, density density, sphere speed, sphere diameter friction force, sphere speed, sphere diameter
THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS/DIAGRAMS LEGIBLY. NO LONG EXPLANATION NEEDED. USE 3 DECIMAL PLACES. BOX THE FINAL ANSWER. A pump discharges into a semi spherical tank at the bottom and cylindrical on top with a radius of 2 meters, and a total tank height of 8 meters. The flow rate is 80 gallons per minute and fluid specific gravity= 1.1. Determine the following: A) flow rate in kg/sec and time it takes to fill the tank in hours. B) the weight in tons of the liquid if full tank local gravity is 32.1 ft/sec squared. C) volume of the tank in metric gallons. D.) how many drums will be needed to transfer all of the tank contents (tank being full) to the drums?
MECHANICAL ENGINEERING UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. SHOW THE STEP-BY-STEP PROCESS WITH SHORT COMMENT/EXPLANATION. ANSWER IN 4 DECIMAL PLACES. Two gaseous streams containing the same fluid enters a mixing chamber and leaves as a single stream. For the first gas the entrance conditions are A1=500 cm², v1=230 m/s, p1=1.60 kg/m³. For the second gas the entrance conditions are A2= 300 cm³, m2=8.84 kg/s, v2=0.502 m³/kg. The exit stream conditions is v3=130 m/s and v3=0.437 m3/kg. Determine the following: (a) the total mass flow leaving the chamber (kg/sec) (b) the velocity of the gas at 2. (m/sec)
THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS/DIAGRAMS LEGIBLY. NO LONG EXPLANATION NEEDED. USE 3 DECIMAL PLACES. BOX THE FINAL ANSWER. An airplane is cruising at an elevation of 35,000 feet from sea level. Determine the amount of gage pressure in bars needed to pressurize the airplane to simulate sea level conditions. The average atmospheric pressure on earth is mated as a function of altitude by the relation Patm = 101.325 (1- 0.02256z)5.256, where Patm is the atmospheric pressure in kPa and z is the altitude in km with z = 0 at sea level.
THERMODYNAMICS (ALREADY ANSWERED IN BARTLEBY. PLEASE CHECK IF THEIR ANSWER IS CORRECT) UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS/DIAGRAMS LEGIBLY. NO LONG EXPLANATION NEEDED. USE 3 DECIMAL PLACES. BOX THE FINAL ANSWER. A pump discharges into a semi spherical tank at the bottom and cylindrical on top with a radius of 2 meters, and a total tank height of 8 meters. The flow rate is 80 gallons per minute and fluid specific gravity= 1.1. Determine the following: A) flow rate in kg/sec and time it takes to fill the tank in hours. B) the weight in tons of the liquid if full tank local gravity is 32.1 ft/sec squared. C) volume of the tank in metric gallons. D.) how many drums will be needed to transfer all of the tank contents (tank being full) to the drums?
Need complete answer ASAP... An object is submerged below the surface of the sea with an exerted pressure of 99.92 bar. How deep is the object submerged? The density of sea water is 1020kg/m3, the gravitational force is 9.7 m/s2, and the atmospheric pressure is 0.98 bar.
THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS/DIAGRAMS LEGIBLY. NO LONG EXPLANATION NEEDED. USE 3 DECIMAL PLACES. BOX THE FINAL ANSWER. A pump discharges into a semi spherical tank at the bottom and cylindrical on top with a radius of 2 meters, and a total tank height of 8 meters. The flow rate is 80 gallons per minute and fluid specific gravity= 1.1. Determine the following: A) flow rate in kg/sec and time it takes to fill the tank in hours. Flow Rate and Time
THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. SHOW THE STEP-BY-STEP PROCESS WITH SHORT COMMENT/EXPLANATION. ANSWER IN 3 DECIMAL PLACES. Note: Use values of MW, Cp, Cv, etc., from the Tables provided below.
Completely solve and box the final answers. Write legibly 4. A single stage air compressor handles 30 cubic meter per minute of atmospheric pressure, 30°C air and delivers it to a receiver at 3.0 mpa. Its volumetric efficiency is 83.0%, compression efficiency of 83.0% and mechanical efficiency of 80.30%. If it rotates at 300 rpm, what power in kW is required to drive it?
A room measures 121⁄2 feet wide and 151⁄2 feet long. The walls are 8 feethigh. The volume of air in the room changes six times each hour. How manycubic feet of air enters the room each minute?
The horizontal force due to water acting on the bolt (Fh): Fh=ρ×A1×V1×V1--V2 Fh=1000×π4×0.0752×1.254×1.254+11.286( Fh)=69.472 This is the only part I did not understand how to get. Can you please explain more? I arrived with this equation, -P1A1 - P2A2 (cancelled since atmos. Pres.) +Fh = rho A1v1 (v2-v1) Why did P1A1 disappear in your solution? How did you come up with (v1 - - v2) ? What is the control volume? Why did you not do a summation of forces is equal to change in momentum but instead go immediately to getting the horizontal force acting on the bolt?