Question 8 A sample slab section view is shown below: *4010"EW 30 Felt Joint El. See What should be the correct reinforcement configuration in plan view for this slab?

Q: 1. What is the design strength of the connection shown below if the plates consist of A572 Grade 50 ...

A:

Q: A fillet-welded joint of 6 mm size is shown in the figure. The welded surfaces meet at 60-90 degree ...

A:

Q: Find the area of the triangle with vertices P(1, 5, -4), Q(0,0, 0) and R(2,4, 1). NOTE: Enter the ex...

A:

Q: Use the moment area method and determine the slope just to the left and just to the right of the pin...

A:

Q: Q.1 The factor of safety against wedge failure along the interface of a soil mass resting on an incl...

A:

Q: The two members used in the construction of an aircraft fuselage are joined together using a 30° fis...

A:

Q: A 3.5-cm-diameter pipe leaves a reservoir of surface elevation 80 m and drops to elevation 47 m, whe...

A:

Q: From the given data of a losed traverse. Distances (m) Bearing N 15°18' E S 85°46' E Lines АВ 368.76...

A: We have to determine the value of bearing of BC and bearing of CD and bearing DA as per the given da...

Q: PROBLEM 5: In Lake Geneva (Switzerland), there is a water jet (called the Jet d'Eau) that is dischar...

A: Velocity is v=2ghv=2×9.81×130v=50.503ms

Q: Two pipes 1 and 2 are connected in series. Pipe 1 is 200 mm in diameter and 300 m long while pipe 2 ...

A:

Q: An earth dam is proposed for a site consisting of a homogeneous stiff clay, as shown in the Fig. bel...

A: Earthfill dam, also known as earth dam or embankment dam, is a dam constructed by compacting success...

Q: Sign false or True and why for the fotlowing- 4-Time mean speed is always less than space mean speed...

A:

Q: can you help me with this question? what would you do if a completed construction causes an accident...

A: Because of the numerous dangers that are required for job site productivity, construction accidents ...

Q: The distance between two lines is determined in the multiline command by one of :the following optio...

A: The scale option of the multiline (MLINE) command defines the offset distance between multiline elem...

Q: 17. Four pulleys are attached to the 50-mm diameter aluminium shaft. If torques are applied to the p...

A:

Q: What are outcrops and sub surface structures

A: Civil engineering structures are constructed anywhere the natural terrain must be changed to allow i...

Q: No. 3. The assembly shown in Figure No. 3 consists of a hollow steel [E = 200 GPa] tube (1) with an ...

A:

Q: INSTRUCTIONS: COPY THE GIVEN TRUSS AND SOLVE FOR THE MEMBER 12 FORCES: АВ. АС, ВС, BD, BE, BF, CF, 1...

A:

Q: 3. a) Draw the free body diagram for the beam. b) Determine the reaction forces and/or reaction mome...

A:

Q: For the beam shown below, derive the expressions for V and M and draw the shear force and bending mo...

A:

Q: Two thin-walled tubular members made of the same material have the same length, same wall thickness ...

A:

Q: 50 m length of tape is of standard length at temperature of 50.76°C. What would be the error in the ...

A:

Q: DETERMINE THE INTERNAL FORCE OF MEMBER DF FROM THE FIGURE BELOW. **Note: for compression, include a ...

A:

Q: USE VIRTUAL WORK METHOD TO DETERMINE THE DEFLECTION AT THE MIDSPAN. 16KN 30 KN/m А B D 2.4 3.2 1.8

A:

Q: Given is an aluminium block: where E= 70 GPa, v= 0.334 Axis Dimensions, mm Loads (kN) 300 50 (T) 400...

A:

Q: SITUATION 9: For Items 28-33. 3 k/ft 2 k/ft im A в с -10 f-10A 15 ft- El = constant 28. What is the ...

A: Given,

Q: For the beams shown in Figs. 1 and 2, determine: Plane stress st ate Princip al stresses Maxim um in...

A:

Q: Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connecte...

A: We have to determine the value of stress (in Mpa) in the bronze if given that P= 188 kN and the diag...

Q: MB = ?

A: Approximate method: - It is a method to analyze structure by taking realistic assumption of specific...

Q: 14 kN/m 7 kN/m 3 m 26. Determine the location of the maximum deflection from left support for the gi...

A:

Q: For the truss loaded as shown, determine the forces in members CD, CJ and IJ. Also identify all zero...

A: We have to find the forces in the members CD, CJ, IJ of the truss

Q: 3. a) Draw the free body diagram for the beam. b) Determine the reaction forces and/or reaction mome...

A:

Q: Y1 V2

A:

Q: 6 kip 8 kip B 4 ft--- 6 ft 4 ft -4 ft

A:

Q: F A El B. C D Ed -d -++d d- Part A - Determining the forces in three members on the right-hand side ...

A:

Q: A fillet-welded joint of 6 mm size is shown in the figure. The welded surfaces meet at 60-90 degree ...

A:

Q: Q1: Find the uplift pressure at important key points, and check the safty against uplift pressure an...

A:

Q: Problem 1. Determine Xg and Yg SECOND TO THE LAST DIGIT DIMENSION OF YOUR STUDENT NO. USE USE DIMENS...

A:

Q: Solve a 100 x 100 x 10mm angle is to be welded to a gusset plate shown. The angle carries a load of ...

A: Given strength of fillet weld 94 mpa  Size of fillet weld = 8 mpa  Load to be carried = 185 kn   

Q: Determine the force in each member of the truss by Method of joints

A:

Q: Pipe 1 which is 150 mm in diameter and 300 m long is in parallel to pipe 2 which is 500 m long. Pipe...

A:

Q: 2. The interval of points 1 and 2 of a main pipeline is composed of 2 km long, 40 cm diameter, and 1...

A: Given, L1 = 2 km or 2000 m L2 = 1.5 km or 1500 m D1 = 40 cm or 0.4 m D2  = 30 cm or 0.3 m 

Q: Q.1 The factor of safety against wedge failure along the interface of a soil mass resting on an incl...

A:

Q: A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm diameter p...

A:

Q: Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is inclined I ...

A: We will solve this question in step no. 2

Q: Q.134 The figure shows a cylinder of 4 m diameter in equilibrium. Calculate the resultant pressure f...

A: The given figure consist of only water Since γw = 10 KN/m3 So, S = 1 for water ABCD part is contacte...

Q: Discover warranty and warranty period in a contract, explain it briefly and include example

A: A warranty is a written guarantee that a seller issues to a buyer regarding particular claims. The c...

Q: A 3.5-cm-diameter pipe leaves a reservoir of surface elevation 80 m and drops to elevation 47 m, whe...

A: ASKED: To calculate the flow rate.   Given, Elevation at reservoir (H1) = 80 mm Elevation at nozzle ...

Q: b) Determine the reaction forces and/or reaction moments at pin (You can neglect the height of the b...

A:

Q: 3. calculate the weight of water (in kN) that must be added to a cubic meter of soil to attain a 95%...

A:

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.