Question 9: A single-phase, 240V/1920V ideal transformer is supplied from a 240V source through a cable of resistance 5 ohm. If the load across the secondary winding is 1.60 kohm. Find the primary current flowing and find the power dissipated in the load resistance.

Question 9: A single-phase, 240V/1920V ideal transformer is supplied from a 240V source through a cable of resistance 5 ohm. If the load across the secondary winding is 1.60 kohm. Find the primary current flowing and find the power dissipated in the load resistance.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Related questions

Q: O-A 400 V. 15 kW, 4 pole, 50 Hz, Y-connected induction motor has full load slip of 4%. The output…

A: We need to find out the torque of the given Motor , first we will find out speed then we will find…

Q: An audio signal 3sin 2π(4000t) amplitude modulates a carrier 5sin 2π(500000t). i) Sketch the…

A: Given: Audio Signal = 3sin 2π(4000t)Carrier Signal=5sin 2π(500000t)

Q: In a short circuit test on a circuit breaker, the following readings were obtained on single…

A: Given: Time to reach the peak restriking voltage, t=50 μs. Peak restriking voltage, Vp=100 kV.

Q: Find the voltage drop across a light bulb if 0.05A current flowing through it for 4 seconds causes…

Q: Why is automation crucial in the modern world?

A: The use of machinery and technology to enable processes to run automatically without requiring human…

Q: INSTRUCTION 1. 2 Simplify the given logic equation then draw the final circuit. X-(AB + BC) + BC (B…

A: This is basic problem of logic gates.

Q: reonstruct the circuit into its appropriate wye/delta form and determine the voltages and currents…

Q: V 0 -V For the following circuit, the vo waveform is C ..... Correct O Wrong O

Q: V1 12 V a P +1 g R1 100 Ω ww ww R3 330 Ω ww R7 100 Ω V2 5 V e h +1 b R2 1 ΚΩ m R5 100 Ω ww R6 10 ΚΩ…

Q: Draw the schematic symbol of the following: a.) function/signal generator b.) diode

Q: 27 kW, 244 V DC shunt motor has an armature and field resistance of 0.04 ohms and 63 ohms…

A: Motor convert electrical energy in to mechanical energy. A starter is device to start or…

Q: * Which circuit is changing the shape of the input Clamper circuit O Clipper circuit O None O

A: The clamper circuit is used to clamp the input voltage at particular value. And clipper is used to…

Q: Q5) Determine the following: A. find the equation of the following circuit in the figure Q5A, and…

A: SOLUTION NOTE PART-A is INCOMPLETE question because…

Q: A 3 kW, 315 V DC series motor is being supplied by a feeder with total resistance of 0.02 ohms and…

A: In this question, We need to determine the armature voltage of the DC series motor. If total…

Q: 1. A 4-pole duplex wound armature has 240 slots and 6 conductors per slot. Determine its speed if…

Q: 2. Compute the root-mean-square value of voltage in a delta-connected alternator with 200 volts per…

A: Given data, Vp=200 V per phase

Q: 2) Derive an expression for the effective index in a slab waveguide as a function of the angle of…

A: SOLUTION LET The incident angle at interface 1 = i…

Q: Using the following characteristics, determine Bac at IB = 60 uA and VCe= 5V * +ic (mA) 7 G…

Q: The value 1.2 × 10-6 can be expressed as

Q: A voltage source of e (t) = 141 sin 377 is applied to two parallel branches. The time In the second…

A: Given- Applied Voltage, e(t)=141 sin377t , i1(t)=7.07ωt-π3 ,i2(t)=10 sinωt+π6 , To find- Total…

Q: A coil is used for producing a flux of 0.24 x 10 webers. If the current flowing in the coil is 2 amp…

A: Given: Coil producing flux, φ=0.24×10-3 Wb. Current flowing in coil, I=2 amp. Coil turns, N=200.

Q: 4. Determine V₁ and V₂ using nodal analysis. Show complete solution using either elimination or…

Q: Calculate the decibel power gain for Ap value of 15 W/W. CA 11.8 dB OB 2 B. 27.1 dB 54.2 dB Oc. D.…

A: Given: Linear power gain, Ap=15 W/W.

Q: 3. Determine all the mesh currents using mesh analysis. Show simplified equations and complete…

A: The given circuit diagram is shown below:

Q: A complex voltage wave is given by v = 200 sin 100лt + 80 sin 300ft + 40 sin 500rt volts. Determine…

Q: For a clamper circuit, if the input is the blue waveform and the output is the red one. Scale…

A: Given that: A clamper circuit waveform is shown below. Scale is 5 V/Div means that one block refers…

Q: Give the different types of Diodes, their operating principles, their operation and their schematic…

Q: 2. From the circuit below, Calculate A. Frequency of Oscillation B. Period of Oscillation 1000…

Q: Q5) Determine the following: A. find the equation of the following circuit in the figure Q5A, and…

A: We need to find out simplify expression for given logic circuit . And we need to find out simplify…

Q: 1. Normally the duration of pulses applied to the set or reset input should only be long enough to…

A: SOLUTION PART-1 ANSWER -(TRUE) The…

Q: For the circuit shown below if Vi is reduced to 100 mV, the voltage VL = V₁-300 V 2092 100 k SKO VL…

A: Note : As per our guidelines we are supposed to answer one question only. So please post remaining…

Q: 244. The apparent power drawn by an a.c. circuit is 20 kVA and reactive power is 12 kVA. The real…

A: Given, Apparent power, S=20 kVA. Reactive power, Q=12 kVAR. Real power, P=?

Q: 1.Determine vo(t) in the circuit, assuming zero initial conditions IH 10(0) V

A: Since only question 1 has been asked, so I am answering 1st question. Given: A circuit with current…

Q: For the pair of waveforms (input and output) captured in that picture, write the mathematical…

A: Given- Vin = Yellow line Vout = Blue line Vin max = 2V Vout max = 440.0 mV Phase = -78.7483 degree…

Q: 9 The rotor of an induction motor has a mo- ment of inertia of 5 kg-m². Calculate the en- ergy…

A: In this question we need to find a energy needed to bring the speed for given cases

Q: 4. Find Ix and Vab from the given circuit below. 50 V + 1 ohm 2 ohms a b + 21x

Q: 16V + ww ΖΩ type your answer... i₁3 The circuit above is in DC steady state. What is the value of it…

Q: accurate to say that a digitizer is a piece of technology that converts analog data to digital?…

A: This has been answered.

Q: The speed of light in a vacuum is 6x10^8 m/s O 1x10^8 m/s O 3x10^8 m/s O O 5x10^8 m/s

A: Speed of light is a constant and it can be determined with the help of Maxwell's law. In a vacuum,…

Q: A galvanometer with a full-scale current of 10 mA has a resistance of 10000. The multiplying power…

A: Given, Im=10 mA Rm=100 ohm Rsh=100 ohm

Q: Can I please have the part a handwritten? I can't tell which variable has the bar sign

Q: can you give me 20 types of lamps?

A: Names of the 20 types of the lamps are given below.

Q: R(s) = = = S G(s) s+3 s+4 C(s)

Q: A power of 10V was applied across the resistance of 100. What is the current flowing through the…

Q: 4. What happens to current when resistance is increased?

A: In this question, We need to discuss about the relation between current and resistance. We know…

Q: Correct the equation VxE=0 for time varying field with necessary derivation.

A: This is a problem of electromagnetism. The detailed solution is given in the next step

Q: G1 12 MVA X₁ = 0,12 pu 11.8 KV O 1.2 33 KV- 6,6 KV- 1.28 1.196 1.32 1.3 T₁12 MVA, X Line-1, Z₁ G2…

Q: 2. Vrms 8 V 5 kHz What is the reactive power in the given circuit? 0 VAR 691 VAR 44.23 mVAR 0.022 μF…

A: Given circuit:

Q: For the figure shown below, do the following: (a) Connect the output line O6 of the decoder to the…

A: To access the data from 4K EPROM, we have used a 3:8 decoder. The memory mapping address is required…

Q: A 6 V battery is connected to a 300 ohm load. Under these conditions, it is rated at 40 Ah. How long…

A: Given: Battery voltage, V=6 V. Load, R=300 Ω. Capacity, C=40 Ah.

Concept explainers

Three-Phase Transformers

Three-segment transformers are a type of transformer used to transform voltages of electrical systems into three ranges. Two type transformers are shell-type transformer and core type transformer. In brief, it could be described because of the exquisite kinds of configurations.

Transformer

Ever since electricity has been created, people have started using it in its entirety. We see many types of Transformers in the neighborhoods. Some are smaller in size and some are very large. They are used according to their requirements. Many of us have seen the electrical transformer but they do not know what work they are engaged in.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
(a) An ideal single-phase two-winding transformer with turns ratio at=N1/N2 is connected with a series impedance Z2 across winding 2. If one wants to replace Z2, with a series impedance Z1 across winding 1 and keep the terminal behavior of the two circuits to be identical, find Z1 in terms of Z2. (b) Would the above result be true if instead of a series impedance there is a shunt impedance? (c) Can one refer a ladder network on the secondary (2) side to the primary (1) side simply by multiplying every impedance byat2 ?
An ideal transformer has no real or reactive power loss. (a) True (b) False
For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
Rework Problem 3.14 if the transformer is delivering rated load at rated secondary voltage and at (a) unity power factor, (b) 0.8 power factor leading. Compare the results with those of Problem 3.14. -
For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
An infinite bus, which is a constant voltage source, is connected to the primary of the three-winding transformer of Problem 3.53. A 7.5-MVA,13.2-kV synchronous motor with a sub transient reactance of 0.2 per unit is connected to the transformer secondary. A5-MW,2.3-kV three-phase resistive load is connected to the tertiary Choosing a base of 66 kV and 15 MVA in the primary, draw the impedance diagram of the system showing per-unit impedances. Neglect transformer exciting current, phase shifts, and all resistances except the resistive load.
An ideal transformer with N1=1000andN2=250 is connected with an impedance Z22 across winding 2. If V1=10000VandI1=530 A, determine V2,I2,Z2, and the impedance Z2, which is the value of Z2 referred to the primary side of the transformer.