Question 9 Ocount below the maximum count allowed per counter.Ocount beyond the maximum count allowed per counter.Ocount up and count down.Orecord the time of an event.QUESTION 9The output Lot Full Light will be energized when the accumulated count is:Ladder logic programL1 Inputs0000300.O 0.100.150.ENTERSWITCHEXITSWITCHRESETENTERSWITCH36EXITSWITCH36C5:1/DN36RESETQUESTION 10When input PB2 is actuated:CTUCOUNT-UP COUNTERCounterPresetAccumulatedrCTDC5:11500COUNT-DOWN COUNTERCounterC5:1PresetAccumulated1500C5:1(RES)(CU) LOT FULL(DN)LIGHT(CD)(DN)LOT FULLLIGHTC5:1(RES)Output L2

QUESTION 9 The output Lot Full Light will be energized when the accumulated count is: Ladder logic program L1 Inputs ENTER SWITCH potop 300. EXIT SWITCH O-RESET O 0. O 100. 150. ENTER SWITCH 36 EXIT SWITCH 36 C5:1/DN E RESET 36 CTU COUNT-UP COUNTER Counter Preset Accumulated CTD C5:1 150 0 COUNT-DOWN COUNTER Counter C5:1 Preset 150 Accumulated 0 (CU) LOT FULL (DN) LIGHT (CD) (DN) LOT FULL LIGHT Output L2 C5:1 (RES)

QUESTION 9 The output Lot Full Light will be energized when the accumulated count is: Ladder logic program L1 Inputs ENTER SWITCH potop 300. EXIT SWITCH O-RESET O 0. O 100. 150. ENTER SWITCH 36 EXIT SWITCH 36 C5:1/DN E RESET 36 CTU COUNT-UP COUNTER Counter Preset Accumulated CTD C5:1 150 0 COUNT-DOWN COUNTER Counter C5:1 Preset 150 Accumulated 0 (CU) LOT FULL (DN) LIGHT (CD) (DN) LOT FULL LIGHT Output L2 C5:1 (RES)

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

The processor has performed the following addition operation: 0x01A0+ 0xC410------0xC5B0 What decimal numbers did the processor add up, and what is the result of the addition if the programmer chose these numbers to be signed 16-bit number, where the lower four bits represent the fractional part of the number?
choose the correct answer Noise margin is the amount of? a. None of the choices are correct b. both signal and noise voltage that a logic gate can tolerate c. signal voltage that a logic gate can tolerate d. noise voltage that a logic gate can tolerate
A simple burglar alarm is to be wired up in a house which has two access doors, A and B. Micro switches are used todetect whether the doors are open or closed with a logic level 0 detected when a door is closed and a logic level Itransmitted when a door is open. The alarm system can also be activated ON and OFF through a concealed manualswitch S. with the system activated; a logic level I is transmitted through switch S. A logic level 0 through switch Sindicates that the system is OFF Devise an appropriate Boolean expression to represent the sound of the alarm Fwhen the system is activated and either, or both, of the doors are opened. construct a circuit diagram for the alarm system and deduce the appropriateBoolean functions:(a) Using NAND gates only.(b) Using NOR gates only
logic circuit just draw the graph please as soon as possible
Implemnt clocked SR flipflop using nor gate. Answer should consist of truth table + logic circuit + a coloum for the state(Set, Rest, Hold, undifned)
Draw the logic circuit diagram. Don't give hand-drawn diagram
2-bit half-adder using logic gates and or not. Please type answer no write by hend.
LOGIC GATE ( NEED ONLY HANDWRITTEN SOLUTION PLEASE OTHERWISE DOWNVOTE).
If R0 = 0x20008000, after run STMDB r0!, {r3, r9, r7, r1, r2} command what is the r7 register memory start address?A. R0= 0x20007ff4B. R0 = 0x20007ffefC. R0 = 0x20007fffD. R0=0x20007fecE. R0 = 0x20007ff0
Design a serial adder using the following: Explain the operation briefly, list thestate table (must include present state, inputs, next state, output and flip-flopinputs) and draw the logic diagrama. Using D flip flop, shift registers and necessary logic gatesb. Using JK flip flop, shift registers and necessary logic gates
simple burglar alarm is to be wired up in a house which has two access doors, A and B. Micro switches are used todetect whether the doors are open or closed with a logic level 0 detected when a door is closed and a logic level Itransmitted when a door is open. The alarm system can also be activated ON and OFF through a concealed manualswitch S. with the system activated; a logic level I is transmitted through switch S. A logic level 0 through switch Sindicates that the system is OFF Devise an appropriate Boolean expression to represent the sound of the alarm Fwhen the system is activated and either, or both, of the doors are opened.
An eight bit number, 01011101, is: 1)added to 4 2) subtracted from -10 3) ANDED with 15 a) What is the outcome of these operations in binary? b) What is this number in decimal? c) What is the original number in decimal?