Question 9. A cylindrical bar of 10.00 mm diameter of some metal is deformed elastically by an axial tensile load of 15,000 N. The diameter of the bar decreases by 0.007 mm subsequent to the load application. (a) Compute Poisson's ratio for this material if its elastic modulus is 100 GPa. (b) What is your best guess on the material being tested?

Question 9. A cylindrical bar of 10.00 mm diameter of some metal is deformed elastically by an axial tensile load of 15,000 N. The diameter of the bar decreases by 0.007 mm subsequent to the load application. (a) Compute Poisson's ratio for this material if its elastic modulus is 100 GPa. (b) What is your best guess on the material being tested?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A sample of giant reed is shaped into a beam with a square cross section of 15.5 mm by 15.5 mm. Two supports placed 22.1 mm apart support thesample and a load is applied halfway between the support points in order to test the force required to fracture the sample. If ultimate tensile strength is912 MPa, what would be the force F (newtons) required to cause failure?
Briefly explain, what are the modulus of elasticity and modulus of rigidity and the relationship between these two modulus?
Calculate the axial deformation of a 1” round steel bar, 1 foot long of material, C1045, when it is subjected to a force of 60,000 axially. Modulus of elasticity = 30 x 10^6 psi. Note: All units are in SI, for your reference.
When an aluminum tensile sample with an initial diameter of 12.827 mm was tested, a maximum load of 66.72 kN was recorded at an engineering strain of 0.4 . What is the load on an identical tensile sample with an engineering strain of 0.2 ?
2) For a brass alloy, the stress at which plastic deformation begins is345 Mpa and the modulus of elasticity is 103GPa.a) What is the maximum load that can be applied to a specimen with area130mm² cross section without plastic deformation? b) If the original length of the specimen is 76 mm, what is themaximum length to which it can be stretched without causing deformationplastic?
Consider a 1 m-long bar of 2024-T81 aluminum alloy with a 20mm-diameter and the following property data: E=70 GPa Y.S = 410 MPa T.S. = 480 MPa % Elongation at failure = 8 % What is the maximum tensile load that can be permitted without producing extensive plastic deformation of the bar? Your answer should be in units of Newtons (N).
Briefly comment on the values obtained for the Elastic Modulus, Yield Strength, Ultimate Strength and Toughness of the test specimen as compared to values of various comparable materials found in the literature. Is the test material comparatively strong? Is it stiff? Is it tough? Yield strength is 186Mpa, elastic modulus is 44.8GPa And the ultimate strength is 238.7mpa
If the axial rigidity of steel bar of 1m length is 200 x 107 N, what will be the axial flexibility of the bar?
Explain the difference between Modulus of elasticity and Stiffness?
Explain why a maximum in stress occurs in the engineering stress—strain curve for a polycrystallinemetal deformed in tension. Why is there no maximum for the true stress— strain curve?
A cylindrical specimen of brass material 11mm in diameter and 110mm long is elastically deformed in tension with a force of 7853N which produces a 4.25x10^-3mm reduction in specimen diameter. Calculate the Poissons ratio for this material
It is known that a brass alloy has a yield strength of 275 MPa, a tensile strength of 380 MPa and a modulus of elasticity of 103 GPa. It is determined that a 12.7 mm diameter and 250 mm long cylindrical sample made of this alloy is elongated by 7.6 mm under the tensile stress effect. Based on this information, is it possible to calculate the magnitude of the load required to generate the said elongation? If possible, calculate, if not, explain why.