Question has been attached in a photo format, explanation not needed, just give the correct answers. I appreicate your time and help. thank you Match the correct heat treatment process to the process descriptions:Rapid cooling of a workpiece after heating to obtainА.desired material properties.Technique used to provide uniformity in grain size andcomposition throughout an alloy resulting in harder andВ.stronger steel, but with less ductility for the samecomposition than full annealing.AnnealingO QuenchingHeating steel below the lowerrecrystallization temperature then air cooling to impartС.some more toughness and reduce brittleness. In thisNormalizingTemperingprocess the steel loses some of its hardness.Heating a material to above itsrecrystallization temperature, holidng it at a suitableD. temperature, and then slow cooling to improve ductility,soften the material, relieve internal stresses, and lessenthe effects of cold working.<>

Answered: Image /qna-images/answer/25cc89b6-e9b2-4e9a-aca4-d8e833ebe412.jpg

Answered: Question has been attached in a photo…

Question has been attached in a photo format, explanation not needed, just give the correct answers. I appreicate your time and help. thank you

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1-discribe how manufacturing Process are classified? 2- llustrate the process which work above recrystallization temperature with neat sketch? 3- Discuss the heat treatment process which uses rapid cooling of steel in oil or molten salt bath?
3 Which of the following process is not an example for Case Hardening process? a. Nitriding b. Carburizing c. Cyaniding d. Annealing
I. A full annealing is often utilized in low- and medium-carbon steels II. A ferritic transformation occurs when the quenching rate is rapid enough to prevent carbon diffusion III. Spheroidizing is the heat treatment method for these steels to develop a machinable and deformable structure Which statement(s) given above is/are correct?
Briefly describe the main microstructure features that can be used to improve an alloy resistance to creep.
- The microstructure for AISI 1080 carbon steel after heat 760°C then For AISI 1080 carbon steel, heat to 760°C after suitable holding time, cool rapidly to 650°C, hold for 90s, then quench to room temperature. A. 50% martensite 50% perlite B.100% pearlite C. 50% bainite 50% pearlite D. 100% bainite -The microstructure for AISI 1080 carbon steel after heat to 760°C then rapidly cool to 600°C, hold for 4 s, rapidly cool to 450°C, hold for 100 s, then quench to room temperature. A. 50% pearlite, 25% bainite, and 25% martensite B. 50% pearlite 50% bainite C. 25% pearlite, 25% bainite, and 50% martensite D. 50% pearlite, 50% martensite - The microstructure for AISI 1080 carbon steel after heat to 760°C then cool rapidly to 400°C, hold for 15 s, then quench to room temperature A. 100% martensite B. 100% bainite C. 50% bainite 50% martensite D. 25%bainite 75% martensite - The microstructure for AISI 1080 carbon steel after heat to 760°C then rapidly cool to 600°C, hold for 90 s, rapidly cool…
Both for Ferritic and Martimenistic sstainless steel belong to the AISI 400 series. Farris stainless steel's are heat treatable grades and Martinisitic stick stainless steel's can only be strain hearted to improve their mechanical properties. True or false
Tempering process is used for low carbon steel. Select one: True False
1-Compact Graphite cast iron was obtained from fast cooling rates.? T F 2-Strength and ductility of nodular iron approximately the same under tension and compressive loads.? T F 3-The grey should be heated to 700 oC for 30 hours to obtain malleable iron? T F 4-The carbon in CGI alloys is neither flakes nor cementite? T F 5-Exhaust manifold manufactured from white cast iron.? T F 6-The reduced section length of the tensile specimen should be at least four times the diameter.? T F 7-Tangent modulus is taken as the slope of the stress–strain curve at yield stress? T…
Austentitic stainless steel's are not hardenable by cold working however Austentic stainless steel's can be strengthened by heat treatment true or false?
A-What is the purpose of the following heat treatments?(mention two points only for each heat treatment). 1-tempering.2-Annealing. 3-surface hardening.
Indicate which microstructures will appear after each induction hardening process step: Options: ( martensite, tempered martensite, bainite, pearlite, austenite) a. tempering. b. Quenching c. Induction heating
Why does the hardness decrease at 600 ° C after rising when the tempering process