what conclusions you can draw from this graph

Q: E 60° 5 cm 20 cm 30 cm

A:

Q: Use the information below to answer the questions that follow. Annual household fuelwood use in…

A: A measure of the energy contained in a fuel or food, derived from the heat released by a specified…

Q: How is a computational solution assessed to be correct, numerically accurate, and physically…

A: given; How is a computational solution assessed to be correct, numerically accurate, and physically…

Q: Discuss the propeller data sheets in aviation in 3 to 5 sentences.

A: First, we have to understand the purpose of a propeller in aircraft: So, the purpose of the…

Q: analyzing a process with an average processing time of 1 minute and an interarrival time of 10…

A:

Q: In part c. Why is h3 taken as hf? Explain the Q lost = Q gained in the picture as well as the graph.…

A:

Q: The area of a rectangle is length times width. Find the areas of rectangles with lengths of 1,3, and…

A:

Q: can u give detail for calculation please, some calculations I stuck

A:

Q: Please write the complete step-by-step solution in a clear manner. Thank you!

A: Given that, Temperature difference limit of carnot cycle=300 °C,TH-TL=0Where,TH=Higher temperature…

Q: Conjecture the introduction of first angle orthographic projection in design.

A: The conjecture first angle orthographic projection in design.

Q: Discuss some of the technical and nontechnical issues that might come up in trying to establish a…

A: Inside the quickening agent, two high-energy molecule radiates go at near the speed of light before…

Q: 5. Find two or more sources with contrasting viewpoints on the same issue. Discuss the main…

A: The procedures or strategies used to find, collect, process, and analyse data about a subject are…

Q: Cite atleast 3 characteristics of a Researcher and explain each?

A:

Q: Do the graphs satisfy Hooke’s law? Why?

A: Consider the diagram shown below for the stress-strain relationship of copper. According to the…

Q: Quality Engineering question Pleas, explain briefly the necessity and benefit of collecting data…

A:

Q: Assuming that this is the FIRST onland discovery on island (meaning: we do not have a similar…

A:

Q: A systematic way to analyze ideas comprises of A. Create a rating scale B. Remove the matrix C. Fill…

A: In this problem, it is asking about the systematic way to analyze the idea is comprises with which…

Q: Search an example of each Research Methods - Quantitative Method, Qualitative Method, and…

A: Quantitative Method uses analyses of numbers to prove hypothesis and to make predictions based on…

Q: Q/What is the design process flow chart

A: Using a diagram known as a process flowchart, the steps of a complicated process may be shown in…

Q: approaches in research. How are the quantitative

A: Approach for quantitative data gathering using

Q: f you were to plot E vs v on a log-log graph what would you expect the slope to be? The expected…

A:

Q: Directions: Answer the given questions. ho1. What is the relationship between decision-making and…

A: Statistical judgments are made based on observations of a phenomena that is subject to…

Q: Mr Hafiz is required to create a survey on his subordinate opinion on cost and standard of living.…

A: Inferential Statistics (for instance, a diagram or chart) and inferential insights permits you to…

Q: Plot DSa and DSw as functions of Tw on a single graph. Plot DSsys [DSsys = DSa +DSw] as functions of…

A: the graphs are in last two pages i solved whole question

Q: What is sensitization and how do you prevent it?

A: Sensitization is the loss of alloy integrity. It results from chromium depletion in the vicinity of…

Q: Analyze the (3) accidents that may happen in a workplace. Please give explanation or justification…

A: Accidents in a workplace may occur due to myriad of reasons. It can be due to : Forces and movement…

Q: If a ball rolls up a ramp to a height of .3 m on the ramp (inclined at an angle of 20 degrees), what…

A:

Q: What is the relationship between the goals of a process system and the risk associated with that…

A: Introduction: Process system is step by step procedure to obtain the desired output by giving…

Q: The following list gives the academic ranks of the 25 female faculty members at a small liberal arts…

A: Required to find  ; 1) Relative Frequencies and percentage of categories. 2) bar graph and pie…

Q: Calorimeters are devices that are commonly used to measure the heating value of fuels. For example,…

A: Junkers Flow Calorimeter:     It goes like this: It is possible to find out how many extra joules a…

Q: What are the benefits of examining and experimenting with a model rather of a physical thing or…

A:

Q: 1. Some people say that computers made life easier and more convenient. Other people say that…

A: At present computer is one of the essential parts of our daily life. Many people of today's society…

Q: 500 lb./ft. 200 lb. 300 lb./ft. 150 lb./ft. 8 ft. 4 ft. 4 ft. 2 ft.

A:

Q: The elastic region of a materials stress strain graph is shown below. Determine the Modulus of…

A: The given stress-strain diagram can be redrawn as below,

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.