Question No. 03 (CLO-3). A rigid bar with negligible mass is pinned at O and attached to two vertical rods, figure 1. Assume the rods are initially stress-free. a) Solve to determine the maximum load P that can be applied without exceeding stresses of 120 MPa in the steel rod, 70 MPa in the aluminum rod and the vertical movement of end C is limited to 5 mm. b) Solve to determine the shearing stress in the pin at O. The pin diameter is 20mm. A C 2m 1m 3m Aluminum A=500mm² A=900mm² E=70GPA L=2.0m Steel Detail of E=200GPA L=1.25m pin at O Figure 1: Question No. 3

Question No. 03 (CLO-3). A rigid bar with negligible mass is pinned at O and attached to two vertical rods, figure 1. Assume the rods are initially stress-free. a) Solve to determine the maximum load P that can be applied without exceeding stresses of 120 MPa in the steel rod, 70 MPa in the aluminum rod and the vertical movement of end C is limited to 5 mm. b) Solve to determine the shearing stress in the pin at O. The pin diameter is 20mm. A C 2m 1m 3m Aluminum A=500mm² A=900mm² E=70GPA L=2.0m Steel Detail of E=200GPA L=1.25m pin at O Figure 1: Question No. 3

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A 1 meter long steel rod AB of 15-mm diameter is held snugly (without any initial stresses) between rigid walls by the arrangement shown in the figure. (STEEL ROD : E = 200 GPa , α= 12 x 10-6/°C , and yield strength σY = 250 MPa.) a) If the rod undergoes a temperature drop of 24°C, and the bolt at B is tightened causing the rod to elongate by 0.0566 mm, determine the bearing stress between the washer and the wall. b) Determine the amount of temperature drop that is allowed if the factor of safety against yieldingis 4.
A rigid bar with negligible mass is pinned at O and attached to two vertical rods, figure 1. Assume therods are initially stress-free.a) Solve to determine the maximum load P that can be applied without exceeding stresses of 120MPa in the steel rod, 70 MPa in the aluminum rod and the vertical movement of end C islimited to 5 mm.b) Solve to determine the shearing stress in the pin at O. The pin diameter is 20mm.
A rigid plate C is used to transfer a 20-kip load P to a steel (E = 30,000 ksi) rod A and to an aluminum alloy (E = 10,000 ksi) pipe B as shown. The supports at the top of the rod and the bottom of the pipe are rigid, and the materials were unstressed before the load was applied. The cross-sectional areas of rods A and pipe B are 0.80 in2 and 3.00 in2 respectively. Determine The normal stress in rod A in ksi, The normal stress in pipe B in ksi and The displacement of plate C in inches. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 5 decimal places.
An aluminum alloy cylinder (2) is clamped between rigid heads by two steel bolts (1), as shown. The steel [E = 200 GPa; α1 = 11.7 × 10−6/°C] bolts have a diameter of 19 mm. The aluminum alloy [E = 70 GPa; α2 = 23.6 × 10−6/°C] cylinder has an outside diameter of 160 mm and a wall thickness of 9 mm. Assume that a = 700 mm, b = 810 mm, and c = 325 mm. If the temperature of this assembly changes by ΔT = 60°C, determine(a) the normal stress in the aluminum cylinder.(b) the normal strain in the aluminum cylinder.(c) the normal strain in the steel bolts.
the 12 kn m torque is applied to the free end of the 6-m steel shaft. the angle of rotation of the shaft is to be limited to 3 degrees. find the diameter d of the smallest shaft that can be used. What will be the maximum shear stress in the shaft? Use G=83GPa for steel
A steel pipe (1) is attached to an aluminum pipe (2) at flange B. Both steel pipe (1) and aluminum pipe (2) are attached to rigid supports at A and C, respectively. Member (1) has a cross-sectional area of A1 = 3,600 mm2 , an elastic modulus of E1 = 200 GPa, and an allowable normal stress of 160 MPa. Member (2) has a cross-sectional area of A2 = 2,000 mm2 , an elastic modulus of E2 =70 GPa, and an allowable normal stress of 120 MPa. Determine the maximum load P that can be applied to flange B without exceeding either allowable stress.
An aluminum tube with the hexagonal cross section shown is 2.5 ft long andhas a constant wall thickness of 0.080 in. Find (a) the largest torque that the tube cancarry if the shear stress is limited to 7200 psi; and (b) the angle of twist caused by thistorque. Use G = 4 * 10^6 psi for aluminum.
A thin cylinder of length 2.5m and diameter 1.0 m is made from 3mm steel plates. Ifa gas is filled in the cylinder at a pressure of 750 kN/m2(gauge). Take E = 210 GPaand ν = 0.3 for steel, determine(i) the hoop stress and longitudinal stress in the wall of the cylinder(ii) the maximum shear stress in the plane of above two stresses(iii) change in diameter of cylinder due to the internal pressure of gas(iv) change in of the cylinder(v) change in volume of the cylinder
A steel rod of length = 3m, diameter - 300 mm and modulus of elasticity = 200 GPa is inserted into an aluminum tube. The aluminum tube as length = 2999.95 mm, wall thickness of 20 mm and modulus of elasticity of 70 GPa. a.) Determine the deformation of each member due to axial compressive force P-100 KN. b.) Determine the stress in each member. c.) Determine the axial strain if no gap exists. WITH FULL SOLUTION ASAP PLEASE
Axial loads are applied to the compound rods that composed of an aluminum segment rigidlyconnected between steel and bronze segments. If P = 25 kN, determine the following: a. Stress in the bronze segment. b. Stress in the aluminum segment. c. Stress in the steel segment.
A horizontal rigid bar ADB of length 3m is pinned to a support at A and held by an inclined wire CD and vertical wire BE. The wires CD and BE are made of steel with diameter of 10 mm and 15 mm, respectively. Determine P if the allowable normal stress for CD and BE is 250 MPa Show complete solution. Thanks