Question No. 06 A hollow steel beam (cross-section shown in figure 5) is subjected to a vertical shear force of 30 kN. Moment of inertia of the cross is IN.A = 383.33x10 in“. a) Solve to determine the maximum shear stress and its location. b) Solve to determine the shearing stress at fiber 75 mm from the top of beam's cross-section. 200 200 300 100 All dimensions in mm

Question No. 06 A hollow steel beam (cross-section shown in figure 5) is subjected to a vertical shear force of 30 kN. Moment of inertia of the cross is IN.A = 383.33x10 in“. a) Solve to determine the maximum shear stress and its location. b) Solve to determine the shearing stress at fiber 75 mm from the top of beam's cross-section. 200 200 300 100 All dimensions in mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1 A beam is subjected to a moment of 972 k-ft. If the material the beam is made out of has a yield stress of 45ksi, what is the required section modulus for the beam to support the moment. Use elastic beam design principles. Submit your answer in in^3 with 2 decimal places. Type your answer... 2 A rectangular beam has a cross section that is 15mm wide and 22mm deep. If it is subjected to a shear load of 23.8 kN, what is the max shear stress in MPa? You may use reduced forms of the shear equation. Type your answer...
For the simply supported beam subjected to the loading shown, sketch the shear force diagram. Determine the largest magnitude shear force. Let a=13.0 ft, b=4.0 ft, c= 8.0 ft, w = 17 kips/ft and M = 243 kip-ft. Give your answer in kips. Enter a positive number. M B C D a
P= 4 kN w= 0.8 kN/m a) Start with the shear diagram. To use a segment of the left end of the beam to develop the expression for the shear, the vertical reaction at A must be known. Calculate the vertical reaction at A. Let a positive force act up. b)Write an expression for the internal shear for an arbitrary point between A and B c)Write an expression for the internal shear for an arbitrary point between B and C.
k P 0 8 ft x = 11.1 ft x RA 8. W (ft) Calculate the magnitude of the bending moment at distance x as shown in the figure. Express your answer in kips.ft, but don't type the unit. Use the following data: P = 15.6 kips w = 9.1 kips/ft Round your answer to one decimal place. 16 ft 6 ft 24. 30. B RB
10 in 1 in 1 in V 12 in 1 in 10 in The wide flange beam above is subjected to a vertical internal shear force V, as shown. Note that the diagram is not shown to scale. Which of the following is closest to the moment of inertia (I) that would be used to calculate the shear stresses on the cross-section due to V? 1051 in4 O 777 in4 O 991 in4 805 in4
QUESTION 3 If the allowable bending stresses for a beam in one application is 6 kip/in2 in tension. The cross-section of the beam is W8 x 40. If the beam is 10 foot long and simply supported and has a concentrated load applied at x = 3 ft as shown below. • Generate the shear force and bending moment diagram in terms of P; • Based on the allowable maximum bending moment you just obtained above, calculate/ input the mazimm allowable value of the load P: please, pay attention to units, and calculate your answer to 1 decimal place.. 3 ft 7 ft kip.
Part A Determine the maximum uniform loading w the W 310 x 21 beam will support if the allowable bending stress is aallow = 170 MPa and the allowable shear stress is Tallow = 92 MPa (Figure 1) Express your answer using three significant figures. Figure 1 of 1 VO AEo It vec W = kN/m Submit Request Answer 3 m 3 m < Return to Assignment Provide Feedback
Q1) A simply supported beam is 3 m long and carries a vertical load of 5 kN at point 1m from the left-hand end. At a section 2 m from the left- hand end a clockwise couple of 3 kN.m is exerted, the axis the couple being horizontal and perpendicular to the longitudinal axis of the beam. The cross section of the beam shown in the figure. Determine the maximum bending stress set-up. 100 60 All dimensions in mm 100 70 30 EERI
Q1) A simply supported beam is 3 m long and carries a vertical load of 5 kN at point 1m from the left-hand end. At a section 2 m from the left- hand end a clockwise couple of 3 kN.m is exerted, the axis the couple being horizontal and perpendicular to the longitudinal axis of the beam. The cross section of the beam shown in the figure. Determine the maximum bending stress set-up. 100 60 All dimensions in mm 100 70 30 EERING
Q1) A simply supported beam is 3 m long and carries a vertical load of 5 kN at point lm from the left-hand end. At a section 2 m from the left- hand end a clockwise couple of 3 kN.m is exerted, the axis the couple being horizontal and perpendicular to the longitudinal axis of the beam. The cross section of the beam shown in the figure. Determine the maximum bending stress set-up. 100 60 All dimensions in mm 100 70 30
a) the bending stress at point A and B on a-a cross section b) the shear stress at point A and B on a-a cross section Section a-a located in the middle of length CD. Length AC = 9 ft, CD = 11 ft, and DB = 5 ft. The dimensions for the rectangular beam are in inches: h = 9, w= 2. 20 kips 20 kips Point A a A C D 9" 10 kips a Point B 2' B
Q/ For the beams and loading shown below. A-Draw the shear force and bending-moment diagrams. B- Determine the equations of the shear force and bending-moment curves for the segments CD in Figure 2 C- Compute the bending stress at point (a) on section C. D- Determine the values and locations of the maximum tensile and compression bending stresses. Figure (2) R Point a Radius of hole: 40kN 0.5m 30 20KN/m 0.7m A B D |B 1m Im 3m Radius = R= 100 mm