e. Determine the maximum allowable value of P
Q: What will be max. height that the water tank that will become full if the max. tangential stress is ...
A: Given data Maximum Tangential Stress = σt = 11700 psi = 11700 x 12 x 12 = 1684800 lb/ft3Given speci...
Q: Write down the Different Characteristics of Isometric Drawing (1-5) III. Arrange the following steps...
A: Characteristics of isometric drawing are: isometric drawing is a 3d representation of an object on a...
Q: Figure 6–22a shows a rotating shaft simply supported in ball bearings at A and D and loaded by a non...
A: Note: As per the platform policy I am unable to upload the photos from the book used for the equati...
Q: What will be max. height that the water tank that will become full if the max. tangential stress is ...
A: Given maximum tensile stress = 11700 psi Thickness of the tank = 0.5 in width of the tank = 15 ft =...
Q: What is the maximum strength, in g/d, of a Cotton fiber when fully loaded with water vapor?
A: from the fiber strength property table we get, the wet strength of cotton is 30 - 54 (g/tex or g/d)
Q: A cat has a body temperature of 48 ºC. She stays inside a closed air conditioned room that has an in...
A: Find the heat loss per unit area from the cate
Q: A 6-m long ladder has a mass of 16 kg, and its center of gravity is 2.4 m from the bottom along the ...
A:
Q: A uniform cylindrical shaft is tested and found to have the above stresses. Find: σ′m and σ′a
A:
Q: Q1) Yousif pushes toward the right on a box with a force of magnitude 31.0 N. Sarah applies an 11.0 ...
A: Given: Fright =31 NFleft=11 NFf=4.50 NR= 98 N
Q: Air passes along an insulated horizontal pipe of 0.05 m2 cross sectional area. In the pipe it passes...
A: Given data Area of insulated pipe = 0.05 m2Temperature at entry = T1 = 20°C = 293 KPressure at entry...
Q: A cylinder in a pneumatic circuit extenders under adiabatic conditions to lift a load. Predict the s...
A: A pneumatic cylinder is a device used to convert energy possessed by compressed air into mechanical ...
Q: iv) Young's Modulus if the elongation is 2.4 mm at 17 kN and (v) Final diameter if the percentage of...
A:
Q: The velocity vector in a fluid flow is given by V = 2xy 3 i – 5x2 yj + 4xyztk. Find the velocity and...
A:
Q: A solid circular steel shaft having an outside diameter of 2.00 in. is subjected to a pure torque of...
A:
Q: GAS MW R (kJ/kgm-K) Cp (kJ/kgm-K) Cy (kJ/kgm-K) k C 28.97 1.4 1.7549 1.4782
A: Answer: The complete table of ideal gas is shown in below attached image:
Q: A steel tank with inner diameter of 5m and a height of 5.20m contains Oil (specific gravity = 0.80)...
A: SPECIFIC GRAVITY Specific gravity, likewise called relative thickness, proportion of the thickness o...
Q: A 25-mm-diameter shaft is statically torqued to 230 N · m. It is made of cast 195-T6 aluminum, with ...
A:
Q: 1. Determine the moment of inertia about an axis perpendicular to the page and passing through the p...
A: GIVEN DATA- A PLATE WITH HOLE GIVEN WE HAVE TO FIND MOI ABOUT AN AXIS PERPENDICULAR TO PAGE PASSING ...
Q: 6. An ideal Otto cycle using air has the following conditions. At point 1; p1 = 14.5 psia and 80° F....
A:
Q: minimum permissible basic circle radius.
A: Given; A cam with a translating flat-face follower is desired to have the follower motion: Yθ=...
Q: ng air has the follo neat added to the air °R and K = 1.4. Con
A:
Q: magnitude of work
A: Given; Mass of air, m=1 kgInitially at temperature, t=1270C=127+273=400 KIt expands reversibily at c...
Q: the streams. There is no odeled as air as an ideal
A: state 1 by ideal gas equation P1V1 = ma RT1100×570060 = ma ×0.287×480ma = 68.9605 kg/sstate 2 30...
Q: List the elements of sustainable development. As an official for the Kajang Municipal Council (MPKJ)...
A: Elements of sustainable development are: 1. People 2. Planet 3. Prosperity 4. Justice 5. Partnership...
Q: The wall thickness of a 1.2 m diameter spherical tank is 1.6875 mm. Calculate the allowable internal...
A:
Q: Consider a steam power plant operating on the ideal Rankine cycle. Steam enters the turbine at 3 MPa...
A: Answer: The thermal efficiency of the ideal Rankine cycle for the following cases are listed below: ...
Q: The homogeneous beam shown in the figure is suspended by a cable at point B and is pin supported at ...
A:
Q: PROBLEM NO. 4 For the truss shown, determine the force in members BD, CD, and CE stating whether the...
A:
Q: DETERMINE THE DEFLECTION AT POINTS B AND D 35 k 2.5 k/ft Hinge A D B 16 ft- -8 ft- – 8ft- 1 = 4,000 ...
A:
Q: Steam at 6.2 MPa and 480 deg. C is received by a regenerative engine with ideal conditions and in an...
A:
Q: Given a 1050 HR steel, estimate Sut = 630 MPa (a) the rotating-beam endurance limit at 106 cycles. (...
A:
Q: 1. Determine the force in members FG,GC and CB of the truss in Fig. Q5 used to support the sign, and...
A:
Q: • A single saturated refrigerating cycle using R-12 as refrigeration operates at condensing temperat...
A:
Q: A crane consisting of an aluminum pole of circular cross section AB pinned to a steel bar AC of circ...
A:
Q: Еxample -1.1- A plate of size 60 cm x 60 cm slides over a plane inclined to the horizontal at an ang...
A:
Q: Calculate the pressure exerted on a floor by a one pointed table leg (170 kg on all four leg) of are...
A: The weight of the load on each leg can be determined as,
Q: True or False: V-type engines have the least vibration in all types of reciprocating engine. Multipl...
A: As per our guidelines we are supposed to answer first three questions. 1. The six cylinders inline ...
Q: DETERMINE THE DEFLECTION AT POINTSB AND C. El=50.0x103 kN-m2 24 kN/m B EI 3.0 m 3.0 m 1.5 m 7.5 m
A:
Q: In traveling a distance of 2.3 km between points A and D, a car is driven at 104 km/h from A to B fo...
A:
Q: A team of professional thieves wants to knock down a castle wall using a primitive explosive. At the...
A: Given: total mass of the explosive(M) = 40 Kg and it breaks into three pieces as shown below:
Q: A grinding ratio of 200 implies that the
A: Given: A grinding ratio 200 implies that the:Where, Grinding wheel refers to the tenacity of hard...
Q: Two horses on the opposite banks of a canal pull a barge moving parallel to the banks by means of tw...
A:
Q: What is h2 in kJ/kg
A: To find h2 in kJ/kg
Q: 10. A garment is rated at 150 F for ironing. An iron is set at 200 W. Is this set- ting appropriate?...
A: The heat transferred between two surface using convection can be determined using the formula given ...
Q: 2. A coin is dropped down to a wishing well with a depth X and 5 sec later, the sounds of the splash...
A:
Q: 2. The truss in Fig. Q6 supports the vertical in members HG and HB of the truss and state if the mem...
A:
Q: Steam at 6.2 MPa and 480 deg. C is received by a regenerative engine with ideal conditions and in an...
A:
Q: ne area of 5,700m2, with its longitudinal centre mine the new draughts forward and aft if a wei, d o...
A: according to questiond2 ∂2udx2=∂2∂t2,0<x<L,t>0since the string is of limited length and it...
Q: Brake power output of the engine ?
A: Given; The indicated power developed by an engine with compressionratio,r=8It is calculated using an...
Q: The change in specific entropy c
A: Given: An ideal gas undergoes a process from; state 1: T1=300 K p1=1 kJ/kg-K state 2: T2=...
Step by step
Solved in 3 steps with 2 images
- A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
- A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?A scuba t a n k (see fig ure) i s bci ng d e signed fo r an internal pressure of 2640 psi with a factor of safety of 2,0 with respect to yielding. The yield stress of the steel is 65,000 psi in tension and 32,000 psi in shear, (a) If the diameter of the tank is 7,0 in., what is the minimum required wall thickness? (b) If the wall thickness is 0.25 in., what is the maximum acceptable internal pressure?
- The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.A vertical pole of aluminum is fixed at the base and pulled at the top by a cable having a tensile force T(see figure). The cable is attached at the outer edge of a stiffened cover plate on top of the pole and makes an angle a = 20° at the point of attachment. The pole has length a = 2.5 m and a hollow circular cross section with an outer diameter d2= 280 mm and inner diameter d1= 220 mm. The circular cover plate has diameter 1.5d2 Determine the allowable tensile force Tallow in the cable if the allowable compressive stress in the aluminum pole is 90 MPa.Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
- A metal bar AB of a weight Ills suspended by a system of steel wires arranged as shown in the figure. The diameter of the wires is 5/64 in., and the yield stress of the steel is 65 ksi. Determine the maximum permissible weight W max for a factor of safety of 1.9 with respect to yielding.A copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN (see figure part a). Use a factor of safety of 1.8 against yielding. (a) If the thickness t of the pipe is one-eighth of its outer diameter, what is the minimum required outer diameter dmin? (b) Repeat part (a) if the tube has a hole of diameter dt 10 drilled through the entire tube, as shown in the figure part b.An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.