The question itself is the text in red. Please show all work, thank you! R= 2.2k+D1vsRvoInput Voltage = Vi = 120 Vrms 60HZOutput Voltage = 6.3 VrmsDiodes = 1N4001vsD2Figure 2. Experiment 2: Full-Wave Rectifier Circuit.If the ripple voltage of this circuit is to be no more than 2V, determine analytically whatcapacitor value needs to be placed in parallel with your load resistor. Include the equationsyou used to determine the value.

Answered: Image /qna-images/answer/59e04bfc-0d32-4f8c-bd24-86772cad9f1f.jpg

R= 2.2k D1 R vo Input Voltage = Vi = 120 Vrms 60HZ vs Output Voltage = 6.3 Vrms Diodes = 1N4001 vs D2 Figure 2. Experiment 2: Full-Wave Rectifier Circuit. the ripple voltage of this circuit is to be no more than 2V, determine analytically what pacitor value needs to be placed in parallel with your load resistor. Include the equations ou used to determine the value.

R= 2.2k D1 R vo Input Voltage = Vi = 120 Vrms 60HZ vs Output Voltage = 6.3 Vrms Diodes = 1N4001 vs D2 Figure 2. Experiment 2: Full-Wave Rectifier Circuit. the ripple voltage of this circuit is to be no more than 2V, determine analytically what pacitor value needs to be placed in parallel with your load resistor. Include the equations ou used to determine the value.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

What is CEMF?
A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance? If a full-wave rectifier is needed?
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
Design rectifier circuits to provide an output of100 VDC using a.) HWR b.) Center-tappedFWR and c.) Bridge-Type FWR circuits. For each circuit, calculate the transformer peakvoltage rating, the diode PIV ratings, and thetransformer turns ratio, if power is taken fromthe 220V line ac supply
Design rectifier circuits to provide an output of100 VDC using a half wave rectifiercalculate the transformer peakvoltage rating, the diode PIV ratings, and thetransformer turns ratio, if power is taken fromthe 220V line ac supply.
Determine the ripple factor for the filtered rectifier circuit below when RL= 4KQ. Then explain briefly the effect of changing in the RL value on the output waveform.
In the figure, SCR semiconductor switched rectifier to a 220 Vrms ac source at 50 Hz, at load Vdc = 100 V, R = 8 Ω and has an inductor large enough to supply continuous current. (a) Trigger angle α = 25o determine the total power absorbed by the load. (b) If the inductance value is 30 mH, the change value from the top Determine.
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
A particular load has to be supplied with an average power of 50mW, 5V dc voltage. Find the value of capacitance and transformer turns ratio in a half wave rectifier with capacitor filter such that the ripple factor should not exceed 1%. Assume 220V rms, 50Hz supply voltage. Also, sketch the voltage waveform across the load.
A 10 V Zener diode is used to regulate the voltage across a variable loadresistor. The input voltage Vs varies between 13 and16 V. The loadcurrent (??) varies between 10 and 85 mA. The minimum Zener current is15 mA. Findi. The maximum value of Rsii. The maximum power dissipated by the Zener diode, using the value ofRs.
A 5V dc stabilized power supply needed to operate a computer is to be produced from a 12V full-wave bridge rectifier using a Zener diode as the regulator circuit. The maximum power rating of the zener diode , Pz is 6W. Calculate the following Maximum current flowing through the zener diode. Value of the series current limiting resistor, Rs. ii. Load current, lc if the load resistor is 50kΩ
For the Zener regulated power supply a shown, the rms value of vI is 15V, the operating frequency is 60Hz, R =100Ω, C =1000μF, the on voltage of diodes D1 and D2 is 0.75V, and the Zener voltage of diode D3 is 15V.(a)What type of rectiﬁer is used in this power supply circuit?(b) What is the dc voltage at V1? (c) What is the dc output voltage VO?(d)What is the magnitude of the ripple voltage at V1? (e) What is the minimum PIV rating for the rectiﬁer diodes? (f) Draw a new version of the circuit that will produce an output voltage of−15 V.