R=100 XL = 202 Xc E= 100V L30° 150 Figure 15.3 a) What is ZT in polar form? b) Calculate the current I. c)Use the voltage divider rule to calculate the voltage across the inductor(coil). d)How could you make the total impedance of this circuit be purely resistive bychange the power source frequency? Explain your result.

R=100 XL = 202 Xc E= 100V L30° 150 Figure 15.3 a) What is ZT in polar form? b) Calculate the current I. c)Use the voltage divider rule to calculate the voltage across the inductor(coil). d)How could you make the total impedance of this circuit be purely resistive bychange the power source frequency? Explain your result.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter13: Transmission Lines: Transient Operation

Section: Chapter Questions

Problem 13.19P

See similar textbooks

Similar questions

A resistor of 51.0 Q, an inductor of 22.0 pH and a capacitor of 150 pF are in parallel. The frequency is 1.00 MHz. Whatis the complex impedance, R_jX? A.51.0_j149. B.51.0_/149 C.46.2_j149. D.46.2_j14.9. ¥ Show Answer Answer: D
Avresistor of 51.0 Q, an inductor of 22.0 pH and a capacitor of 150 pF are in parallel. The frequency is 1.00 MHz. Whatis the complex impedance, R_jX? A.51.0_j14.9. B.51.0_/149 C.46.2_j14.9. D.46.2_j14.9. ¥ Show Answer Answer: D
The transmission line in Figure Q.1 (a) now is shorten to L=λ/4 and the input impedance Zin is set to be 75 ohms. The load, ZL is 200 ohms. Determine the new characteristic impedance of the transmission line, Zo to matched the load to the input.
In a series circuit of R = 15 Ω and L = 0.06 H, the voltage across the inductance is VL = 240sin (500t) V. Find the total voltage, current, the angle by which i lags VT and the magnitude of the impedance.
A resistor of 100 Ω, a coil of 4.50 uH and a capacitor of 220 pH are in parallel. What is the impedance vector at8.50 MHz?A. 100 + j 240 ohms C. 100 – j 240 ohmsB. 258u + j160.6 m ohms D. 258u - j160.6m ohms
Solve no.15 and show solutions. (Situation no.06 image below)
1. If the impedance of the circuit when expressed in polar form has a magnitude of _____ ohms and an angle of _____ degrees. Select the correct answer below: -5, 53 -5, -53 5, 53 5, -53 2. if the impedance is drawn as a phasor diagram, it would look like an arrow drawn _____ making an angle of _____ degrees from the positive horizontal axis. Select the correct answer below: a. diagonally on the 4th quadrant, 53 b. diagonally on the 4th quadrant, -53 c. diagonally on the 1st quadrant, -53 d. diagonally on the 1st quadrant, 53 3. if V1 is made the reference phasor, then its phasor diagram would look like an arrow drawn _____ making an angle of _____ degrees from the positive horizontal axis Select the correct answer below: a. horizontally to the right, 0 b. horizontally to the left, 0 d. horizontally to the right, 180 e. horizontally to the left, 180
Find the total current to the parallel circuit of L = 45 mH and C = 400 µF with an applied voltage of v = 110sin(100t) V. Also, what is the total impedance, and power factor of the circuit? Is the circuit inductive or capacitive?
Given the circuit below, find the new impedance if the frequency were halved. Round off to 4 decimal places. Original condition: R = 104 ohms, XL = 28 ohms, XC = 57 ohms, and f = 189 Hz
Three coils connected in series across a 100 V, 50 Hz supply have the followingparameters:R1 = 18 Ω, L1 = 0.012 H; R2 = 12 Ω, L2 = 0.036 H; R3 = 3.6 Ω, L3 = 0.072 HDetermine the potential drop and phase angle for each coil. USE SERIES AC CIRCUITS METHOD NOT KIRCHOFF LAWS. PLS SHOW COMPLETE SOLUTION AND ROUND OFF TO FOUR DECIMAL PLACES , WRITE LEGIBLY PLS INLUDE ALSO THE CIRCUIT DIAGRAM:
Suppose that the modulating signal m (t) is sinusoid of the formm (t) = 10 COS ( 2π103t) and the carrier signal C(t) is sinusoid of the form C(t) = 4 COS ( 2π106t + Ɵ)1. According to the previous results which type of AM is the best in respect toa. Power transmitted b. band widthJustify your answers2. Draw the block diagram for both DSBSC and DSBFC with all parameters.
meet.google.com/abd-sfsj-rhf