Rankine cycle running on saturated steam, which the turbine operates at steady state with inlet conditions of 17.5 MPa, 1100°C and dryness fraction is = 1.21. Steam leaves turbine at a pressure of 3.5MPA, and x 1- dryness fraction x 2- the enthalpy difference between these two steates (3-4) 3- the enthalpy difference between these two steates (1-2) 4- work ratio of the cycle

Rankine cycle running on saturated steam, which the turbine operates at steady state with inlet conditions of 17.5 MPa, 1100°C and dryness fraction is = 1.21. Steam leaves turbine at a pressure of 3.5MPA, and x 1- dryness fraction x 2- the enthalpy difference between these two steates (3-4) 3- the enthalpy difference between these two steates (1-2) 4- work ratio of the cycle

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i.Drawaschematic diagramof each problem with labels of states of a substance; ii.For uniformity purposes, assign STATE 1 at the inlet of ahigh-pressure turbine.The states must be arranged in a chronologicalorder; iii.Ploteach cycle in a t-s diagramwith the states consistentto the states assignment in the schematic diagram; iv.Show a detailed solution An ideal reheat Rankine cycle with water as the working fluid operates the boiler at 10MPa, the reheater at 2MPa, and the condenser at 0.1MPa. The temperature is 4500C at the entrance of the high-pressure and low-pressure turbines. The mass flow rate through the cycle is 1.74 kg/s. Determine a)the rate of heat transfer in the reheater, and b) thecyclethermal efficiency.
A 120 MW gas turbine power plant running on Ideal Brayton cycle has the followinginitial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature atthe turbine entrance is 910°C. Determine the following: a. Pressure & temperature at each stateb. T-S diagramc. Heat Added, per unit mass
Rankine cycle running on saturated steam, in which the turbine operates at steady state with inlet conditions of 17.5 MPa, 1100°C and dryness fraction is = 1.21. Steam leaves turbine at a pressure of 3.5MPA, and x 1- dryness fraction x 2- the enthalpy difference between these two steates (3-4) 3- the enthalpy difference between these two steates (1-2) 4- work ratio of the cycle
A 150 MW gas turbine power plant running on Ideal Brayton cycle has the following initial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature at the turbine is 910°C. Draw the P-V and T-S diagrams and determine the following: d. Thermal Efficiency e. Mass flow rate, kg/min
A gas turbine power plant working on Brayton cycle, Explain the working principle of the cycle with physical diagram as well as P-V and T-s diagrams, and with all the required details
Based on a gas turbine with superheat and intercooling, determine: 1) The thermal efficiency (ƞterm), in %. Use the expression ƞterm= 1 –(qL/ qH)2) How does gas turbine intercooling influence thermal efficiency?3) How and why? It is said that the gas turbine cycle with intercooling, reheating and regeneration is close to the Ericsson cycle.
A gas-turbine power plant operating on an ideal Brayton cycle has a pressure ratio of 8. The gas temperature is 300 K at the compressor inlet and 1300 K at the turbine inlet. Utilizing the air-standard assumptions and by accounting for the variation of specific heats with temperature, determine the thermal efficiency. The air can be treated as an ideal gas with κ = 1,4 and cp = 1006 J/(kg·K).
In an air-standard Brayton cycle the air enters the compressor at 0.1 MPa and 15°C. The pressure leaving the compressor is 1.0 MPa, and the maximum temperature in the cycle is 1100°C. Determine the pressure and temperature at each point in the cycle and the compressor work, turbine work, and cycle efficiency. For each of the control volumes analyzed, the model is ideal gas with constant specific heat, at 300 K, and each process is steady state with no kinetic or potential energy changes
Design a steam power cycle that can achieve a cycle thermal efficiency of at least 40 percent under the conditions that all turbines have isentropic efficiencies of 83 percent and all pumps have isentropic efficiencies of 65 percent. please include (i) System figures and T-s diagrams with labelled states and temperature, pressure, enthalpy, and entropy information for your design. (ii) Sample calculations.
Q#1. A gas-turbine plant operates on the regenerative Brayton cycle, the schematic diagram of whichis shown in Fig. Q 1, with two stages of reheating and two-stages of intercooling between the pressure limits of100 and1200 kPa . The working fluid is air. The air enters the first and the second stages of the compressor at 300 K and 350 K , respectively, and the first and the second stages of the turbine at 1400 K and 1300 K , respectively. Assuming both the compressor and the turbine have an isentropic efficiency of 80%. The regenerator has an effectiveness ofεregen=75% . Assume variable specific heats (i.e., use the concept of relative pressures) and the intermediate pressuresof intercooling and reheating is the square root of the product of inlet and exit pressures for intercooling and reheating. Make other the necessary assumptions and determine(a) the back work ratio,β , and the net work output,, wnet(b) the thermal efficiency (that is the first-law efficiency,ηi ) and(c) the…
Rannkin cycle 1_The value of enthalpy at point 1 is ( h1 =?) 2_ value of enthalpy at point 2 is ( h2 =?) 3_ value of enthalpy at point 3 is ( h3 =?) 4_value of enthalpy at point 4 is ( h4 =? 5_ value of steam mass flow rate in kg/s is 6_rate of heat supplied7_ power developed by Turbine (WT) in kW is : 8_ Thermal efficiency of Rankine cycle is:
PART D only A gas-turbine power generator operates on an ideal air-standard Brayton cycle 1 → 2 → 3 → 4 shown in Fig. 1. The gas temperatures at the compressor inlet, compressor exit, and turbine inlet are T1 = 300 K, T2 = 600 K, and T3 = 1200 K, respectively. Solve PART D below using the variable specific heat assumption PART D - Evaluate the thermal efficiency η of the cycle and the back work ratio rBW = wC/wT.