Q4//All The open cycle gas turbine using intercooling, regeneration and reheating. arrangement with pressure ratio 49, compressor inlet temperature 27'C, turbine inlet temperature 1300 "C. compressor efficiency 0.86, turbine efficiency 0.87, regenerative effectiveness 0.8, combustion efficiency 0.99, mechanical efficiency of whole assembly 0.97, generator efficiency 0.98, inlet pressure to compressor Tbar. Determine:1- cycle work, 2- cycle thermal efficiency, 3- cycle work ratio. [

Q4//All The open cycle gas turbine using intercooling, regeneration and reheating. arrangement with pressure ratio 49, compressor inlet temperature 27'C, turbine inlet temperature 1300 "C. compressor efficiency 0.86, turbine efficiency 0.87, regenerative effectiveness 0.8, combustion efficiency 0.99, mechanical efficiency of whole assembly 0.97, generator efficiency 0.98, inlet pressure to compressor Tbar. Determine:1- cycle work, 2- cycle thermal efficiency, 3- cycle work ratio. [

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Based on a gas turbine with superheat and intercooling, determine: 1) The thermal efficiency (ƞterm), in %. Use the expression ƞterm= 1 –(qL/ qH)2) How does gas turbine intercooling influence thermal efficiency?3) How and why? It is said that the gas turbine cycle with intercooling, reheating and regeneration is close to the Ericsson cycle.
Q1 : In a steam power plant , steam enters at 8 MPa and 700 C , the condenser pressure is 8 kPa , and the net power out of the plant is J100MW . Determine enthalpy and entropy at point 1, dryness frection , and enthalpy and entropy at point 2 , enthalpy and entropy at point 3 , work torbine , work net , Qadd to boiler , thermal efficency for cycle , Q rejeted from condenser , mass flow rate of steam , Q rejeted from condenser
An ideal Diesel engine operates on 0.63 lbm of air with a suction state at 14 psia and 140 °F. The pressure at the end of compression is 458 psia and the volume at the end of heat addition process is 0.13 ft^3. Using air properties (R=53.34 ft-lbf/lbm-R, k=1.4, Cp =.24, Cv=.1714 Btu/lbm-R), determine compression ratio, percentage clearance, Qa, Qr, Thermal Efficiency, mean effective pressure. Plss Show complete solution with the corresponding unit cancellation. Thank you
In an air standard Brayton cycle the air enters the compressor at 0.1 MPa, 25 ∘C. The pressure leaving the compressor is 1 MPa. and the maximum temperature in the cycle is 1200 ∘C. Assume a compressor efficiency of 80%, a turbine efficiency of 85%, and a pressure drop between the compressor and turbine of 30 kPa. Use the PG model. a) Determine compressor work (w_C), b) Determine the turbine work (w_T), c) Determine the cycle efficiency (n_th,Brayton).
For a steam turbine with the following data: Initial Temperature T0=36,7°C,Final temperature after the boiler T4=690,1°C , the initial pressure beingp0 = 1 bar, with a medium temperature Tm=151,9°C. Calculate the turbine efficiencyfor a simple Rankine proccess (without regenerative heating nor reheating). Results in %
Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 300 K, with a volumetric flow rate of 5 m³/s. The turbine inlet temperature is 1800 Κ.For a compressor pressure ratio of 6, determine:(a) the percent thermal efficiency of the cycle.(b) the back work ratio.(c) the net power developed, in kW.
Rannkin cycle 1_The value of enthalpy at point 1 is ( h1 =?) 2_ value of enthalpy at point 2 is ( h2 =?) 3_ value of enthalpy at point 3 is ( h3 =?) 4_value of enthalpy at point 4 is ( h4 =? 5_ value of steam mass flow rate in kg/s is 6_rate of heat supplied7_ power developed by Turbine (WT) in kW is : 8_ Thermal efficiency of Rankine cycle is:
Provide complete solution and detailed diagram. A Brayton cycle has an initial air temperature of 30oC. If pressure ratio is 12, find thecompressor work. A. 310.28 KJ/kg B. 313.28 KJ/kg C. 316.28 KJ/kg D. 319.28 KJ/kg
Consider a cold air-standard Diesel cycle. Operating data at principal states in the cycle are given in the table below. The states are numbered as in Fig. 9.5 with p1 = 100 kPa, T1 = 340 K, and T3 = 4850.3 K, r = 12 and rc = 2. For n = 1.3, cv = 0.718 kJ/(kg-K), and cp = 1.005 kJ/(kg-K), determine p2 in kPa.
A generator uses a gas turbine cycle. Air enters the compressor at a pressure of 1 bar and a temperature of 30°C with a compressor efficiency of 0.85. Hot gas exits the combustion chamber at a pressure of 9 bar and a temperature of 900°C. The power generated by the turbine is 2400 kW with a turbine efficiency of 0.82. a. Draw installation diagrams and T-s cycle process diagramd b. Determine the work of the compressor and turbine and the mass rate of the air requirement c. Cycle thermal efficiency (air: Cp=1,005 kJ/kg. K dan γ=1.4; Gas hot: cp=1,005 kJ/kg K and γ=1.4)
A 120 MW gas turbine power plant running on Ideal Brayton cycle has the followinginitial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature atthe turbine entrance is 910°C. Determine the following:a. Thermal Efficiencyb. Mass flow rate, kg/min
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Here are the questions to be answered: 1. Why is the value of Wexp 0? (Explain) 2. Given the above values, can you calculate the Wflow? (Yes/No)