Determine ratio of friction energy to total energy 5. An orthogonal cutting operations is being carried out in which uncut thickness is 0.010mm, cutting speed is 130 m/min, rake angle is 15° and width of cut is 6 mm. It isobserved that the chip thickness is 0.015 mm, the cutting force is 60 N and the thrustforce is 25 N. The ratio of friction energy to total energy is

Given: An orthogonal cutting operation is being carried out in which uncutthickness is,t=…

Answered: ratio of friction energy to total…

Engineering

Mechanical Engineering

ratio of friction energy to total energy

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A viscously damped system having resonant amplitude of 1.5 m, spring of stiffness of 1600 N/m is sub...

A: Given: The amplitude, x = 1.5 The spring stiffness, k = 1600 N/m The harmonic loading, F = 300 N

Q: There are different Mechanical models that can describe the viscoelastic characteristics of a materi...

Q: A venturimeter has an ratio 9 to 1, the larger diameter being 300 mm. During the flow, the recorded ...

A: The greatest diameter of a venturimeter is 300 mm, and the ration is 9 to 1. The recorded pressure h...

Q: Determine 0g and 8g at point B usıng dou

Q: The polyethylene liner of a settling pond is subjected to stresses σx = 350 psi, σy = 112 psi, and τ...

A: Given σx = 350 psi, σy = 112 psi, τxy = -120 psi Find Normal stress

Q: The displacement of a particle is given by s = 3t - 50t² + 91t - 53 where s is in feet and t is in s...

Q: Which of the following are the functions of a volute casing in a centrifugal pump? (a) To collect wa...

A: It is required to choose correct answer

Q: Convert 755.0 mm of mercury to oil of SG 0.82. Round your answer to 3 decimal places

Q: Define the necessary equations to find the behavior of the mechanism (reduced at its maximum express...

A: It is asked to find the behaviour of mechinsam in terms of a mathematical model

Q: A test on centrifugal pump operating at 3463 rpm showed a total head of 48 ft at a capacity of 900 g...

Q: A composite bar is fabricated by brazing aluminum alloy [E= 10,000 ksi] bars (1) to a center brass [...

Q: The acceleration of a particle is given by a = 3t - 34, where a is in meters per second squared and ...

Q: The stepped solid steel shaft ABC is attached to rigid supports at each end. Determine the diameter ...

Q: What piece of equipment should you use in order to obtain the mass of the weighing form? Double b...

Q: A 2-stage centrifugal pump delivers 50 gpm of 225oF water against 200 ft head at 3200 rpm. a) What i...

Q: what are the mechanical differences between 4 wheel drive, front wheel drive and rear wheel drive sy...

A: given; what are the mechanical differences between 4 wheel drive, front wheel drive and rear wheel d...

Q: A diver is 203ft below the free surface of the sea. The barometric pressure is 14.57 14.7psia and SG...

A: Pressure at any point in a fluid at a rest is obtained by hydrostatic law which states that the rate...

Q: Here, 20 degree celcius water is being siphoned from a reservoir, see attached image. What would be ...

Q: Describe the environmental impacts of wind power systems and explain how the negative impacts of win...

A: Solar energy comes in the form of wind. The method of generating electricity with wind energy (o...

Q: The velocity of a particle moving in the x-y plane is given by (5.72i + 7.27j) m/s at time t = 5.22 ...

A: Given: V1 = (5.72i + 7.27j) m/s a = (3.1i + 8j) m/s

Q: Using the polar formula prove that?

Q: Equation of Motion(NORMAL AND TANGENTIAL) Fn= Man Ft= Mat Given a 1400 kg car that travels along a r...

Q: execution of a reversible nonflow process, the work is 216 kJ. If the initial pressure and volume 60...

Q: A 10 cm long sample of some material elongates 0.2 mm when heated from 25°C to 200°C. Calculate the ...

Q: Magnetic tape is being transferred from reel A to reel B and passes around idler pulleys Cand D. At ...

Q: copper tube with circular cross section has length L = 1.85 m, thickness t = 3 mm, and shear modulus...

A: given length(L)=1.85 m thikness(t)=3mm elasticity (G)=45 Gpa ...

Q: Superheated steam at 90 bar, 625 °C (State 1) undergoes a 3-step process: (i.) First, it is throttle...

Q: Determine the x- and y-coordinates of the centroid of the shaded area. Ans. = 0.762, y 0.533 %3D %3D...

Q: TOPIC: Equation of Motion (NORMAL AND TANGENTIAL) Fn= Man Ft= Mat Given a 1400 kg car that trave...

Q: Consider the processes shown below for a monatomic ideal gas. p (atm) . 5- B 2- A D 3 7 V(L) a. Find...

A: (a) Write the given data in the problem. P1=2 atmP2=5 atmV1=3 LV2=7 L Here, P1 is the pressure at A ...

Q: 4. Nylon strips are fused to glass plates. When moderately heated the nylon will become soft while t...

Q: Consider the following figure: a Yo Assume b=1, d=2, e=3. Find the magnitude of the translation vect...

A: Transformation Matrix Changes are utilized to plan an image into another with various sizes, positio...

Q: 3. Find the beam deflection y(x) that satisfies El = W (x) for 0 < x < 2c . %3D Wo 30 20 UIN

Q: Two indefinitely long flat plates separated by 3 inches in distance but with a thickness of 5 inches...

A: Given Viscosity = 1 Pa.s Density = 0.89 x 1000 Velocity, v = 5 m/s Thickness, t = 5 in =...

Q: A car is traveling around a circular track of 760-ft radius. If the magnitude of its total accelerat...

Q: L. Scale the following vectors using the ratio 100 km: 1 cm Given Magnitude 350 km Scaled Magnitude ...

Q: The uniform solid block in the figure has mass 22.6 kg and edge lengths a = 0.884 m, b = 1.31 m, and...

A: Answer: The rotational inertia about an axis through one corner and perpendicular to the large faces...

Q: Reqd: Determine e of A relative to D Gs = 12 x 10° psi MN Ib ft 1000 Ib ft 900 Ib ft 2-in. diame SN ...

A: The simplified diagram of the shaft is as shown below,

Q: Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-d...

A: Answer: The maximum allowable value of load that can be applied on the joint is 37.7 kN.

Q: v (m/s) 10 t(s) 15 60 90

Q: Roger Federer is practicing an optimum "return of serve". Given the conditions on the B figure, (a) ...

A: (a) Write the given data. hA=7.2 fthB=3.5 ftsAB=21.5 ft

Q: Determine the force, in kN, due to water acting on one side of the parabolic gate. Round your answer...

A: Answer: The force due to water acting on one side of the parabolic gate is 141.26 kN.

Q: Topic: Mechanics of Deformable Bodies: Analysis on Trusses

Q: Le expected life (

A: To find Expected life of bearing

Q: 3. Based from the pump performance curve below, calculate the following: a) Specific speed b) Suctio...

A: Given data Pump performance curve From the pump performance curve, specific speed and suction speci...

Q: tipod shawn supports that ball and rocket joints are used to mount the tripud points BID,and C. oad ...

Q: 3. Based from the pump performance curve below, calculate the following: a) Specific speed b) Suctio...

A: Given data pump performance curve Specific speed and Suction Specific speed is to be calculated.

Q: A 3.8 kg block is attached to a vertical spring with spring constant 18 N/m. At one instant, the blo...

Q: Which of the following are the functions of a volute casing in a centrifugal pump? (a) To collect wa...

A: It is required to choose correct answer

Q: F00 mm w = 35 kN/m 38-mm diameter s38-mm diameter 50-mm diameter 300 mm 100 mm

Concept explainers

Forms of Energy

Energy is described as the capability to accomplish a task, like the ability to push a block by applying force on it. It is a quantitative property that is used to accomplish work on an object.

Question

Determine ratio of friction energy to total energy

5. An orthogonal cutting operations is being carried out in which uncut thickness is 0.010
mm, cutting speed is 130 m/min, rake angle is 15° and width of cut is 6 mm. It is
observed that the chip thickness is 0.015 mm, the cutting force is 60 N and the thrust
force is 25 N. The ratio of friction energy to total energy is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Assume that, in orthogonal cutting, the rake angle is 20 and the friction angle is 35 at thechip-tool interface. Determine the percentage change in chip thickness when the frictionangle is 50. Note that Merchant’s equation is more preferable.
A tool with zero rake angle used in orthogonal cutting when its clearance angle a is changed from 10 to 7 deg, Calculate the approximate % change in the life of the tool.
2 1.23 Tool life can be almost infinite at low cutting speeds.Would you then recommend that all machining be done at low speeds? Explain.
In orthogonal turning of a low carbon steel bar of diameter 150 mm with uncoated carbide tool. the cutting velocity is 90 m/min The feed is 0.24 mm/rev and the depth of cut is 2 mm. The chip thickness obtained is 0.48 mm If the orthogonal rake angle is zero and the principal cutting edge angle is 90° Calculate the shear angle in degree.
Assuming that the coefficient of friction is 0.25, calculate the maximum depth of cut forturning a hard aluminium alloy on a 15-kW lathe (with a mechanical efficieny of 80%) at awidth of cut of 6 mm, rake angle of 0˚, and a cutting speed of 90 m/min, shear strength of 150 MPa.
Assume that in orthogonal cutting the rake angle is 15o and the coefficient of friction is 0.15. Using Eq. 8.20, determine the percentage increase in chip thickness when the coefficient of friction is doubled.
Write down the steps required to proof the mathematical relation for SHEAR PLANE ANGLE in Orthogonal Cutting Model. i-e. Prove the following relation:
a) It has been stated that it is generally undesirable to allow temperatures to riseexcessively in machining operations. Explain why?b) List out the cutting parameters which is influenced the rises of cuttingtemperature during turning process.c) Evaluate the relationship of these cutting parameters to the cutting temperaturewith graph.d) Propose the solution of how to reduce the temperature during the cuttingprocess.
In face milling, assume that the Diameter of the cutter is 200 mm, the width of the block is 60 mm, and the length of the block is 344 mm, if the depth of cut is 3 mm, = 0.6 mm/min, and N = 100 rpm. The cutter has 12 inserts, and the workpiece material is bronze. Calculate the estimated power required, the cutting force, and the torque.
Make a figure and explain how shear plane angle effect the power requirements in the machining. How can you reduce the power requirements during machining in orthogonal cutting? plzz do it in 45 minutes
2 1.49 Assume that, in orthogonal cutting, the rake angle is 15° and the coefficient of friction is 0.2. Using Eq. (21.4),determine the percentage increase in chip thickness when the friction is doubled.
A flat milling operation will be carried out with a horizontal milling machine, in a piece of 250 mm in length and 50 mm in width, using a felicoidal bur with a diameter of 75 mm, with 10 teeth. If the feed per tooth is 0.2mm, and the cutting speed is 0.75 m / s, how would you determine the speed of metal removal to remove 6 mm from the surface of this piece?