Read the question carefully and answer with complete solution and units. The two decimal places for solution and final answers. 1. An air standard Otto cycle receives air at too kPa and 325K. During the heat addition process, the heat added is 850 kJ/kg. The compression ratio of this cycle is 8. Draw the PV and TS diagrams, find the temperature at each point, Whet. and efficiency. Answer: 325K, 746. 65k, 1932.15 K, 840.29 K, 480.02 КЈ kg 56-47% )

Read the question carefully and answer with complete solution and units. The two decimal places for solution and final answers. 1. An air standard Otto cycle receives air at too kPa and 325K. During the heat addition process, the heat added is 850 kJ/kg. The compression ratio of this cycle is 8. Draw the PV and TS diagrams, find the temperature at each point, Whet. and efficiency. Answer: 325K, 746. 65k, 1932.15 K, 840.29 K, 480.02 КЈ kg 56-47% )

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 285 K, with a volumetric flow rate of 5 m3/s. The compressor pressure ratio is 11:1. The turbine inlet temperature is 1400 K. Take Specific heat at constant pressure and constant volume for air as 1.001 kJ/kg K and 0.710 kJ/kg K respectively. Calculate the turbine exit absolute temperature to one decimal place and place the correct unit.
Multiple Choice. Choose the correct answer and show COMPLETEsolution. (Brayton Cycle) 18. An air standard Brayton cycle operates with compression ratio of 6 and temperatureat the start and end of heat addition are 170°C and 820°C. Find the temperature at theend of expansion.a. 261 °Cb. 83 °Cc. 400 °Cd. 990 °C
In an air standard Brayton cycle the air enters the compressor at 0.1 MPa, 25 ∘C. The pressure leaving the compressor is 1 MPa. and the maximum temperature in the cycle is 1200 ∘C. Assume a compressor efficiency of 80%, a turbine efficiency of 85%, and a pressure drop between the compressor and turbine of 30 kPa. Use the PG model. a) Determine compressor work (w_C), b) Determine the turbine work (w_T), c) Determine the cycle efficiency (n_th,Brayton).
Air enters the compressor of an ideal air-standard Brayton cycle at 119 kPa, 328 K, with a volumetric flow rate of 1358 m3/s. The compressor pressure ratio is 8. The turbine inlet temperature is 1358 K. Take Specific heat at constant pressure and constant volume for air as 1.006 kJ/kg K and 0.717 kJ/kg K respectively. Calculate the work ratio of the plant to one decimal place and include the correct unit (percentage). Us cold air standard assumption.
The compression ratio of an Otto cycle is 8, at the beginning of the zanthropic compression process, the pressure of the air is 100 kPa, the temperature is 27 "C, the volume is 550 cm. At the end of the lzantropic expansion process, the temperature of the air is 700 K. Using the specific temperature values at room temperature (according to the cold air standard assumptions) Find the gravity of the air.
Pls answer thank you! A gas turbine operating in an ideal open cycle is served by a compressor which receives air at 15 psia, 80°F and 13.32 cu. ft/lb and delivers it to the combustion chamber at 60 psia. In the combustion chamber 300 Btu are added at constant pressure to each pound of air flowing. Steady flow conditions exit throughout the cycle. Using constant specific heat, calculate the compressor work, Btu/lb .
Given a Brayton cycle, with a pressure ratio equivalent to 12, as shown in the figure, determine its thermal efficiency, in %. Use Standard Cold Air Assumption Method (constant specific heats at room temperature, 25ºC).
Write legibly so i can understand 4. In a Brayton cycle, air enters the compressor at 101.32 kPaa and leaves at a pressure of 808 kPaa. The air is heated to 717 o C in the combustor. For a net output of 2125 kW, compute: a) Mass flow rate (kg m/s ), b) power to drive compressor (kW), c) Gross power (kW) , d) thermal efficiency, e) mean effective pressure (kPaa)
A reheat cycle with two stages of reheating is executed, with steam expanding initially from 202.65 and 540 deg. C. The two reheater pressures are 40 bar and 10 bar, and steam leaves each reheater at 540 deg. C. Condensation occurs at 60 deg. C. Sketch the Ts - diagram. For an ideal cycle, find Qa and e. For the engine operating between the same conditions compute W and e. For a 362, 500 kg/h steam and 100 MW generator output at 94% efficiency, for actual engine, find combined thermal efficiency and combined heat rate and combined engine efficiency and quality of the actual exhaust steam. (3 decimal places in final answer pls)
Air enters the compressor of an ideal air standard Brayton cycle at 100 kPa, 290 K, with a mass flow rate of 6 kg/s. The compressor pressure ratio is 10. The turbine inlet temperature is 1500 K. If a regenerator with an effectiveness of 70% is incorporated in the cycle, determine (i)turbine work, (ii) compressor work, (iii) heat supplied, and (iv) the efficiency of the cycle. Draw a suitable block diagram and T-s diagram. Take Cp=1.005 kJ/kg K and ϒ= 1.4
Air enters the compressor of an ideal air-standard Brayton cycle at 88 kPa, 280 K, with a volumetric flow rate of 1225 m3/s. The compressor pressure ratio is 12. The turbine inlet temperature is 1225 K. Take Specific heat at constant pressure and constant volume for air as 1.006 kJ/kg K and 0.717 kJ/kg K respectively. Calculate the thermal efficiency of the plant to one decimal place and include the correct unit (percentage). Use cold air standard assumption
A simple saturation cycle using ammonia between pressures of 10 psia and 165 psia is tobe replaced with two stages of compression and water intercooling of vapor from the firststage to 50 OF as entering temperature to the second stage . For the same stroke and workingcharacteristics in both stages , what would be the ratio of the cylinder diameters of the firststage to the second stage .A) 1.75 B) 2.95 C) 1.95 D) 2.75