Read the question carefully before answering. Box or indicate your final ansurers when solving and draw your diagrams cleanly. Complete solution please. Use 2 decimal places when solving and for final answers. Draw the PV and TS diagram with proper label of points when required. 1. An Otto Cycle receives air at 101 kPa and 20c, then compresses it to 10% of the original volume. The max temperature of the air is 1050 k Draw the PV and TS diagrams, and selve for the following: the remaining temperatures, QA, QR. Whet and efficiency.

Read the question carefully before answering. Box or indicate your final ansurers when solving and draw your diagrams cleanly. Complete solution please. Use 2 decimal places when solving and for final answers. Draw the PV and TS diagram with proper label of points when required. 1. An Otto Cycle receives air at 101 kPa and 20c, then compresses it to 10% of the original volume. The max temperature of the air is 1050 k Draw the PV and TS diagrams, and selve for the following: the remaining temperatures, QA, QR. Whet and efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

complete solutions with four decimal digits. Box the final answers, Write legibly. In a Rankine cycle, saturated liquid water at 1 bar is compressed isentropically to 150 bar.First by heating in a boiler, and then by superheating at constant pressure of 150 bar, thewater substance is brought to 750 K. After adiabatic reversible expansion in a turbine to 1bar, it is then cooled in a condenser to a saturated liquid. Using steam tables, what is thethermal efficiency of the cycle?
Please help with all questions, thank you so much in advance!! Determine (1) The power input to the compressor (2) The rate of heat removal from the refrigerated space (3) The pressure drop and in the line between the evaporator and the compressor (4) The rate in the line between the evaporator and the compressor (5) and sketch the T-s diagram for this cycle with corresponding saturation lines
An air-standard set of processes with constant specific heats is executed in a closed system and is composed of the following:1-2 Isentropic compression from 100 kPa and 25°C to 600 kPa2-3 Isometric heat addition to 1500 K3-4 Isentropic expansion to 100 kPa4-1 Isobaric heat rejection to initial state Question: Following the given data, perform the following:a. Plot the P-V and T-S Diagram of the cycleb. Calculate the net work output of the cycle (kJ/kg)c. Calculate the Thermal Efficiency (%)
Read the questions carefully before answering. Box or indicate your final answers when solving and draw your diagrams cleanly or use correction tape/fluid. Use the steam tables provided and DO NOT ROUND the values from the steam table. Use 4 decimal places when solving and use 2 decimal places for final answers only. Draw the TS diagram with proper placement and label of points when required. A Steam power plant operates using the ideal Rankine Cycle where steam initially enters the turbine at 5.0 MPa and 400 C then after expanding, it condenses at 7 kPa and exits as saturated liquid. Draw the TS diagram, find the thermal efficiency, and steam rate.
2. How do you determine the mass of bleed steam in an open heater ?
Please use property tables. Thank you Steam enters the high-pressure turbine of an ideal reheat Rankine cycle at 10 MPa and 500°C. The low-pressure turbine inlet admits steam at 1 Mpa. Assume that the pump inlet is a saturated liquid at 10 kPa and that 80 MW of power is produced overall. 1. Report the amount of heat added in the reheat process, in kJ/kg, to one decimal place using rounding. 2. Report the amount of work produced in the low-pressure turbine, in kJ/kg, to one decimal place using rounding.
Please provide the correct answer and explanation. 1. Compressor process in a reciprocating compressor cannot be achieved by Constant temperature process Isentropic process Polytropic process Constant pressure process 2. In an Otto cycle, during the compression process, Pressure remains constant Work done is zero Volume remains constant Heat transfer is zero 3. In an actual refrigeration cycle, the increase in entropy and heat transfer is due to Reversibility Atmospheric pressure Frictional effects Adiabatic compression
25 - The refrigerant R-134a enters a throttling valve as a saturated liquid at 1400 kPa and leaves at 240 kPa. Which of the following is the degree of dryness of R134a leaving the valve? a) 0.3434 B) 0.4075 NS) 0.4520 D) 0.3339 TO) 0.4297
Read the questions carefully before answering. Box or indicate your final answers when solving and draw your diagrams cleanly or use correction tape/fluid. Use the steam tables provided and DO NOT ROUND the values from the steam table. Use 4 decimal places when solving and use 2 decimal places for final answers only. Draw the TS diagram with proper placement and label of points when required. A Steam power plant operates using the actual Rankine Cycle where steam initially enters the turbine at 5.0 MPa and 400C then after an irreversible adiabatic process, it exits the turbine with a dryness of 90. It then condenses at 7 kPa and exits as saturated liquid. Draw the TS diagram, find the thermal efficiency, and steam rate.
Draw a neat diagram of a regenerative gas turbine and reheater and also explain it working with a help of a P-V diagram?
A generator uses a gas turbine cycle. Air enters the compressor at a pressure of 1 bar and a temperature of 30°C with a compressor efficiency of 0.85. Hot gas exits the combustion chamber at a pressure of 9 bar and a temperature of 900°C. The power generated by the turbine is 2400 kW with a turbine efficiency of 0.82. a. Draw installation diagrams and T-s cycle process diagramd b. Determine the work of the compressor and turbine and the mass rate of the air requirement c. Cycle thermal efficiency (air: Cp=1,005 kJ/kg. K dan γ=1.4; Gas hot: cp=1,005 kJ/kg K and γ=1.4)
Using T- diagrams , explain why superheating and reheating is necessary in a vapor power cycle from the functional perspective . Also show how it helps improve the efficiency of the cycle .