Read the question carefully before answering. Box or indicate your final ansurers when solving and draw your diagrams cleanly. Complete solution please. Use 2 decimal places when solving and for final answers. Draw the PV and TS diagram with proper label of points when required. 2. A Diesel aycle receiver air at 15 pria and 75F. The cycle has √ 4³ 15 and QA = 352 Btu Draw the PV and TS diagram. Solve for the remaining 1b. temperatures, Qr, Wnet, officiency and how many 16 of air is required if the engine is 500 hip?

Read the question carefully before answering. Box or indicate your final ansurers when solving and draw your diagrams cleanly. Complete solution please. Use 2 decimal places when solving and for final answers. Draw the PV and TS diagram with proper label of points when required. 2. A Diesel aycle receiver air at 15 pria and 75F. The cycle has √ 4³ 15 and QA = 352 Btu Draw the PV and TS diagram. Solve for the remaining 1b. temperatures, Qr, Wnet, officiency and how many 16 of air is required if the engine is 500 hip?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I want to know how this problem can be done using mollier-chart please let me know what I did wrong in the Attached mollier-chart picture so the solution didn't come out to be right. The problem A steam power plant, operating with one regenerative feed water heating at the initial steam conditions of P=35 bar, T=440°C, exhaust pressure at 0.04 bar. Steam is bled from the turbine for feed water heating at a pressure of 1.226 bar.Determine1-Specific heat consumption2- Thermal efficiency of the cycle3- Thermal efficiency of the cycle neglecting regeneration
A reheat cycle with two stages of reheating is executed, with steam expanding initially from 202.65 and 540 deg. C. The two reheater pressures are 40 bar and 10 bar, and steam leaves each reheater at 540 deg. C. Condensation occurs at 60 deg. C. Sketch the Ts - diagram. For an ideal cycle, find Qa and e. For the engine operating between the same conditions compute W and e. For a 362, 500 kg/h steam and 100 MW generator output at 94% efficiency, for actual engine, find combined thermal efficiency and combined heat rate and combined engine efficiency and quality of the actual exhaust steam. (3 decimal places in final answer pls)
Thermodynamics: - Clear writing please!!! Thank you - Sketch and label all numbers on the turbine. - Sketch and label all numbers on the process on a T-s diagram. 7.133E A large condenser in a steam power plant dumps 15 000 Btu/s by condensing saturated water vapor at 115 F with an ambient temperature of 77 F. What is the entropy generation rate?
Draw a schematic diagramof each problem with labels of states of a substance; For uniformity purposes, assign STATE 1 at the inlet of a high-pressure turbine. The states must be arranged in a chronological order; Plot each cycle in a t-s diagram with the states consistent to the states assignment in the schematic diagram; An ideal Rankine cycle with double reheat operates the boiler at 12MPa, the reheater at 5 MPa and 2.0 MPa, and the condenser at 0.01 MPa. The temperature at the boiler and reheater outlets are maintained at 400°C. a) Determine the total rate of heat transfer per unit mass in the reheaters, and b) the thermal efficiency of this cycle.
Brayton cicle Based on a gas turbine with superheat and intercooling, determine: 1) The thermal efficiency (ƞterm), in %. Use the expression ƞterm= 1 –(qL/ qH)2) How does gas turbine intercooling influence thermal efficiency?3) How and why? It is said that the gas turbine cycle with intercooling, reheating and regeneration is close to the Ericsson cycle.
Please use property tables. Thank you Steam enters the high-pressure turbine of an ideal reheat Rankine cycle at 10 MPa and 500°C. The low-pressure turbine inlet admits steam at 1 Mpa. Assume that the pump inlet is a saturated liquid at 10 kPa and that 80 MW of power is produced overall. 1. Report the amount of heat added in the reheat process, in kJ/kg, to one decimal place using rounding. 2. Report the amount of work produced in the low-pressure turbine, in kJ/kg, to one decimal place using rounding.
Please use property tables. Thank you Steam enters the high-pressure turbine of an ideal reheat Rankine cycle at 10 MPa and 500°C. The low-pressure turbine inlet admits steam at 1 Mpa. Assume that the pump inlet is a saturated liquid at 10 kPa and that 80 MW of power is produced overall. 1. Using the property tables for both the inlet and outlet of the pump, determine the enthalpy in kJ/kg of the pump outlet. Report your answer to two decimal places using rounding. 2. Report the amount of heat added, in kJ/kg, in the boiler before the high-pressure turbine to one decimal place using rounding. 3. Report the amount of work produced in the high-pressure turbine, in kJ/kg, to one decimal place using rounding.
complete solutions with four decimal digits. Box the final answers, Write legibly. In a Rankine cycle, saturated liquid water at 1 bar is compressed isentropically to 150 bar.First by heating in a boiler, and then by superheating at constant pressure of 150 bar, thewater substance is brought to 750 K. After adiabatic reversible expansion in a turbine to 1bar, it is then cooled in a condenser to a saturated liquid. Using steam tables, what is thethermal efficiency of the cycle?
An Otto cycle begins its compression at 94kPa, 1230cm^3 and 11degC. The dispalacement volume and maximum temperature within the cycle is 1090cm^3 and 920degC and respectively. Utilizing air standard assumptions, determine the: a. heat addition and Wnet (kJ) b. thermal efficiency (%)c. mean effective pressure (kPa) Consider the cycle as a model of the process in each cylinder of a spark-ignition engine. Show the T-s and P-v diagrams when solving. Note that specific heats are not constant
A reversible refrigerator operates using a Carnot refrigeration cycle. It operates usingr-134a between 140 and 400 kPa. The refrigerant exits the compressor (and enters the condenser) assaturated vapor. It also leaves the condenser as saturated liquid.a. Sketch the P-v and T-s diagram of this cycle. Define the coordinate properties of each state oneach graph.b. Evaluate the specific heat and specific work properties of each (in kJ/kg). Indicate the sense.c. Evaluate the coefficient of performance using the specific heats and works from the previousitem. Did it match with the COPR obtained if you used the operating temperatures? Solve for states first. Then, show the solution to each of the above required in order.
i.Drawaschematic diagramof each problem with labels of states of a substance; ii.For uniformity purposes, assign STATE 1 at the inlet of ahigh-pressure turbine.The states must be arranged in a chronologicalorder; iii.Ploteach cycle in a t-s diagramwith the states consistentto the states assignment in the schematic diagram; iv.Show a detailed solution An ideal reheat Rankine cycle with water as the working fluid operates the boiler at 10MPa, the reheater at 2MPa, and the condenser at 0.1MPa. The temperature is 4500C at the entrance of the high-pressure and low-pressure turbines. The mass flow rate through the cycle is 1.74 kg/s. Determine a)the rate of heat transfer in the reheater, and b) thecyclethermal efficiency.
THERMODYNAMICS Consider an air-standard Otto cycle with a heat addition of 800 Btu/bm of air, a compression ratio of 7, and a pressure and temperature at the start of the compression process of 13 lbf/in2, 50 F to simulate an actual spark-ignition engine. Determine the maximum pressure and temperature of the cycle, the thermal efficiency of the cycle, and the mean effective pressure assuming the variation of specific heat with the value from table A-19E Show Complete solution on a paper.