Refer to the figure below. The square steel tube carries 130 kN of axial compressive force. Compute the compressive stress in the tube and the bearing stress between each contacting surface. Consider the weight of the concrete pier to be 2000 N. 100 mm 100 mm 4 mm Standard strudural steel tube-100x 100x 4 ,150 mmx 150 mm plate 300 mmx 300 mm Concrete pier 600 mm 600 mm Gravel

Refer to the figure below. The square steel tube carries 130 kN of axial compressive force. Compute the compressive stress in the tube and the bearing stress between each contacting surface. Consider the weight of the concrete pier to be 2000 N. 100 mm 100 mm 4 mm Standard strudural steel tube-100x 100x 4 ,150 mmx 150 mm plate 300 mmx 300 mm Concrete pier 600 mm 600 mm Gravel

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

•Timber beamSafe working stress = 25 MPaCross-section dimensions:height = 119 mm,width = 66 mmProving ring number 293. Steel beam Safe working stress = 200 MPa Cross-section dimensions:external height = 149 mm,external width = 50 mm,wall thickness = 3.0 mm,Proving ring number 1522.1)Calculate safe max bending moment in the central part of the beam using Mmax = (I)(max stress)/(D/2)2) calculate Safe applied force in the proving ring or tie rod, assuming a symmetrical setup as in the photowith a ‘lever arm’ of 600 mm
Let the allowable stresses in the post be ??? = 120 ??? and ??? = 6 ???. Compute the maximum safe axial load P that may be applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Each steel bar has cross-sectional area of 900??2
What is the internal force in member AB? A. 750 N , T B. 450 N , T C. 750 N , C D. 450 N , CSHOW SOLUTIONS
1. A simply supported beam 300 mm wide, 500 mm deep and spans 5.7 m supports a service super imposed dead load of 9 kN/m and service live load of 9 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the depth of equivalent rectangular stress block (mm) at ultimate stage. Write your answer in 2 decimal places only. 2. A simply supported beam 300 mm wide, 500 mm deep and spans 5 m supports a service super imposed dead load of 7 kN/m and service live load of 6 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
5. A rectangular beam 350 mm wide is to be designed for an ultimate moment of 750 kN·m with f’c = 28 MPa and fy = 415 MPa. The effective depth of the tension bars is 500 mm and 70 mm for compression bars. a. Determine the depth of the stress block if the tensile strain is 0.005 when the concrete crushes at a strain of 0.003. = ____ mm (one decimal place) b. Determine the total amount of tension reinforcement for the given condition above. = ___ sq.mm (whole number) c. Determine the amount of compression reinforcement required. = ___ sq.mm (whole number)
Determine the maximum tensile stress σtand maximum compressive stress σc due to the load Pacting on the simple beam AB (see figure).(a) Data are P = 6.2 kN, L 5 3.2 m, d =1.25 m,b = 80 mm, t = 25 mm, h =120 mm, andh1 = 90 mm.(b) Find the value of d for which tensile andcompressive stresses are the largest. What arethese stresses?
Topic: Basic Formulas Used in Steel Design: (Allowable Stress Design) ASD Problem: A simple beam has a span of 10m and supports a superimposed uniformly distributed load of 20 kN/m. Properties of W450x70 A = 8700 mm² bf = 150 mm tf = 15 mm d =450 mm Ix = 274.7 x10⁶ mm⁴ Iy = 8.47 x106 mm⁴ tw = 10 mm Wb = 70 kg/m a. What is the average shearing stress in the beam? b. Determine the maximum shearing stress in the beam. c. Calculate the maximum bending stress in the beam.
Given: Mmax= 15.625 kN-m Vmax= 12.5 kN Depth of the beam= 250 mm 1. A simply supported 5 meter timber beam carries a 5 kN/m uniformly distributed load. If the beam's Ix is 260.4166 x 10^6 mm^4 and fb = 7.50 MPa, what is the base of the beam? a) 150 mm b) 180 mm c) 200 mm d) 220 mm 2. The shear stress fv developed for the beam of question 1 is a) 0.375 MPa b) 0.50 MPa c) 0.75 MPa d) 0.85 MPa
Refer to the figure below.The square steel tube carries 100kN of axial compressive force. Compute the compressive stress in the tube and the bearing stress between each contacting surface. Consider the weight of the concrete pier to be 1000 N.
Calculate Tension BD if P = 100 kN.
A simply supported concrete beam 6m long is reinforce with four-28 mm diamgram tension bars. The beam has a width of 300mm and over all depth of 400.the steel covering to the centroid of the renforcement is 70 mm fc=30mpa and fy 418mpa A .draw a stress diagram B.compute for the ultimate capacity of the beam
The aluminum block has a rectangular cross section and is subjected to an axial compressive force of 8 kip. If the 1.5-in. side changed its length to 1.500132 in., determine Poisson’s ratio and the new length of the 2-in. side. Eal = 10(103 ) ksi.