solve below Problem 4It is given a pipe, which is narrowed in section, asshown on the figure, from diameter D = 200 mm till d100 mm. It is known that the velocity in the wide cross-section in the pipe is 0,8 m/s. Determine the differenceAh in the piezometers readings.h1D|AhdH,0Z172

Answered: Image /qna-images/answer/ca599282-d1ca-4643-be89-3140184de21b.jpg

Answered: relocity in

Engineering

Mechanical Engineering

relocity in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The above pipe is exchanged for a parallel pipe with a cross sectional area of 0.3m2 and is 20 m long, with a surface roughness coefficient of 0.005. The dynamicviscosity of the water is 1.002 x 10-3 Ns/m. Find the Reynold’s number of the flowand use Haarland’s formula to find the friction coefficient and Darcy’s formula todetermine the frictional pressure loss. Then determine the pressure at the outlet ofthe pipe.
The system consists of 1200 m of 5 cm cast iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m3/s of water into the reservoir? Use the following: v = 1 x 10-6 m2/s Kentrance = 0.5 Kexit = 1 Kvalve = 6.9 f = 0.0316 γ = 9810 N/m3 Choices: 3.44 Mpa 1.02 MPa 3.48 Mpa 1.00 MPa None of the choices
Flow takes place between three reservoirs, as shown in Figure 1. The volume flow rateout of reservoirs A and B is 0.15 m3/s and 0.25 m3/s respectively. If the coefficient offriction for the three pipes is 0.008, determine the relative elevations of the freesurfaces. Neglect all losses other than friction. PLEASE USE THE BERNOULLI EQUATION L1 = 1000 m D1 = 200 mmL2 = 1500 m D2 = 250 mmL3 = 2000 m D3 = 400 mm
Question : SAE 30 oil at 20°C flows in the 3.5-cm-diameter pipe, which slopes at 37°. For the pressure measurements shown, determine Part (a) whether the flow is up or down and Part (b) the flow rate in m3/h. Neglect minor losses. Directions - Solve carefully, Write Clear, Label as Part (A) and (B) Circle Final answer(s) Hint : flows in the 3.5-cm-diameter pipe, *** USE IMAGE BELOW Pb = 190kPa, Pa = 550kPa, 25m, etc
Water flows through the following circular pipe with a diameter of 30 mm at a speed of 3 m/s, what is the hydrodynamic entry length? The water dynamic viscosity is 1.002×10-3kg/(m⋅s).
(i)Determine the equivalent pipe corresponding to three (3) pipes in series with lengths and diameters l1, l2, l3, d1, d2, d3 respectively. (ii)A jet strikes tangentially a smooth curved vane moving in the same direction as the jet, and the jet gets reversed in the direction. Show that the maximum efficiency is slightly less than 60 per cent
(a) Prove that the loss of pressure head for the viscous flow through a circular pipe is givenby h. (b) Determine (i) the pressure gradient, (ii) the shear stress at the two horizontal parallelplates, and (iii) the discharge per meter width for the laminar flow of oil with a maximumvelocity of 1.5 m/s between two horizontal parallel fixed plates which are 80 mm apart. Takeviscosity of oil as 1.962 Ns/m2.
A pipe with unequal ends is used to transport a fluid. The pipe diameter at the larger end is 0.67 cm and the other end is 0.29 cm. The larger and smaller ends are located 9 m and 3 m, respectively, from the datum line. If the flow at the 9 m datum line is 1.48 m/s and the pressure is 5156 kN/m2, compute for the pressure, in kPa, at the smaller end. Express your answer in 3 decimal places.
Water flows at the rate of 0.80m3/s in a 900-m long pipe. The total head loss in the pipe is 4m. Which of the following most nearly gives the diameter of the pipe using the Darcy-Weisbach formula with f = 0.018?
A certain amount of water (H2O) flows permanently into the pipe venturi(image2) in the figure next to it. In the stretch considered between (1) and (2), it is assumed the losses by friction that were despicable and the uniform properties in the sections are assumed. The entrance area is A1 while that of throat is A2 (A1 > A2). A pressure gauge whose manometric fluid is Mercury Hg (YHg> YH2O) is connected between the input sections and the throat. Show, without omitting any calculation steps that the flow rate at the input (1) is given by(image1):
Water fills a cylindrical tank to depth h . The tank hasdiameter D . The water fl ows out at average velocity V o from a hole in the bottom of area A o . Use the Reynoldstransport theorem to fi nd an expression for the instantaneousdepth change dh/dt .
What are the velocities of pipes in series, with Q =3.28 cum./sec. of a Pipe 1 connected to Pipe 2 and then connected to Pipe3 with the corresponding diameters D1=1.60m, D2=1.80m, & D3=2.00mrespectively ? Neglect the headloss due to pipe enlargement, He = 0 Continuity Equation: Q = A1 x v1 = A2 x v2 = A3 x v3 a)Calculate velocity in pipe 1, V1 = ? in meters ( V1 = ? , in meters/second) b) Calculate velocity in pipe 2, V2 = ? in meters ( V2 = ? , in meters/second) c) Calculate headloss in pipe 3, V3 = ? in meters) ( V3 = ? , in meters/second)