Replace the loading by an equivalent resultant force and couple moment acting at point O. (Eigure 1) The loading function is w- 8² lb/ft. Figure 10 f Part A Determine the magnitude of the equivalent resultant force. Express your answer in pounds to three significant figures. 13Η ΑΣΦΑ FR = Submit Part B 7= Submit Part C Specify the location of the equivalent resultant force on the beam, measured from the left end. Express your answer in feet to three significant figures. VAE Ivec 4 Request Answer (MR)O= Submit Request Answer vec a -Η ΑΣΦΑ 11 vec Request Answer ? ? Determine the equivalent resultant couple moment about point O. Express your answer in kilopound-feet to three significant figures. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise. lb ft ? Review kip-ft

Replace the loading by an equivalent resultant force and couple moment acting at point O. (Eigure 1) The loading function is w- 8² lb/ft. Figure 10 f Part A Determine the magnitude of the equivalent resultant force. Express your answer in pounds to three significant figures. 13Η ΑΣΦΑ FR = Submit Part B 7= Submit Part C Specify the location of the equivalent resultant force on the beam, measured from the left end. Express your answer in feet to three significant figures. VAE Ivec 4 Request Answer (MR)O= Submit Request Answer vec a -Η ΑΣΦΑ 11 vec Request Answer ? ? Determine the equivalent resultant couple moment about point O. Express your answer in kilopound-feet to three significant figures. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise. lb ft ? Review kip-ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The shaft is supported at its ends by two bearings AA and BB and is subjected to the forces applied to the pulleys fixed to the shaft. (Figure 1) The T1=T1= 585-NN forces act in the -zz direction and the 200-NN and 80-NN forces act in the +yy direction. The journal bearings at AA and BB exert only yy and zz components of force on the shaft. Part A Determine the resultant normal force on the cross section at CC. Express your answer to three significant figures and include appropriate units. NC= values ? NC= units? Determine the resultant shear force in the yy direction on the cross section at CC . Express your answer to three significant figures and include appropriate units. (VC)y Values ? (VC)y units ?
Determine the magnitude of moment (Nm) of the 383-N force about point A if x = 0.55 m , y = 0.69 m, and θ = 41.4ᵒ. Round off only on the final answer expressed in 3 decimals. Instead of units, type either POSITIVE or NEGATIVE to indicate the direction of moment which is consistent with the sign convention discussed on lectures. Sample answers are 12.908 POSITIVE or 12.908 NEGATIVE
The bar supported by a pin at B and a cable at A carries a load of 260 N at C. Neglecting the weight of the bar,a.) Determine the normal force 7 m from A.b.) Determine the shear force 7 m from A.c.) Determine the bending moment 7 m from Ad.) Determine the torsion 7 m from A SHOW COMPLETE SOLUTIONS DRAW FBD
Q13. As shown in the image below, the member is subjected to the applied loads: a free couple moment M=320lb*ft, concentrated force F1=380lb, and concentrated force F2=220lb. The dimension a=5.5ft. Determine the magnitude of the resulatant moment (in lb*ft) caused by these applied loads about point A. Answer must inculde 1 place after the decimal point.
Q1 / B : 1. Convert the moment of 500 Ib.S to SI units *
#1: A moment Macts on the brake drum shown. The radius of the drum is 150 mm. If mu = 0.35 between the drum and belt, calculate the larger tensile force exerted by the belt. Also, determine the magnitude of the braking moment M due to the vertical force P = 120 N.
Take that w0 = 4.6 kN/m. Replace the loading by an equivalent force. Express your answer to three significant figures and include the appropriate units. Enter positive value if the force is upward and negative value if the force is downward. Replace the loading by a couple moment acting at point O. Include clockwise or counterclockwise.
1. F1 and F2 forces AB in the system whose loading condition is given in Figure The tensile force in the chain is in balance with the Fab. of force F2 Calculate the magnitude and cosine directives. F1(N)=60 Fab(N)=100 a(°)=20 b(°)=50
The stress–strain diagram for a titanium alloy can be approximated by the two straight lines. If a strut made of this material is subjected to bending, determine the moment resisted by the strut if the maximum stress reaches a value of (a) sA and (b) sB.
Determine the algebraic sum of the moments of forces relative to a point in F = 10.0 N; m =9.0 Nm, q =8.0 N/m
Use the picture to solve these questions 1-The magnitude of the moment induce by the load about the Line-EF is _____ kN*mm. 2- The direction of the moment induce by the load about the Line-EF is _____ kN*mm. 3- The direction of the moment induce by the load about the Line-CD is _____ kN*mm. 4- The state of the internal force at the mid-point of Member-BD _____ . Enter "1" for "tension". Enter "2" for "compression" Enter "3" for "torsion" Enter "4" for "neither tension, nor compression, nor torsion 5- The state of the internal force at the mid-point of Member-BF _____ . Enter "1" for "tension". Enter "2" for "compression" Enter "3" for "torsion" Enter "4" for "neither tension, nor compression, nor torsion
A hollow steel crank has an outside diameter of 26 mm and an inside diameter of 21 mm. The load magnitudes are Py = 690 N and Pz = 270 N, and the length dimensions are a = 145 mm, b = 399 mm, and c = 261 mm. Determine the magnitudes of the equivalent forces and the equivalent moments that act at the section that contains point K. (a) Axial force in x direction Px (N (b) Shear force in y direction Vy (N (c) Shear force in z direction Vz (N (d) Torque around x axis Tx (N·m) (e) Bending moment around y axis My (N·m) (f) Bending moment around z axis Mz (N·m) Calculate the section properties for the hollow crank at K. (g) Area A (mm2) (h) Polar moment of inertia J (mm4) (i) Area moment of inertia Iy (and Iz) (mm4) (j) QK (for shear force in y-direction) (mm3) Using the sign conventions, determine the normal and shear stresses that act at K and show these stresses on a stress element. (k) Normal stress in x direction σx(MPa) (l) Normal stress in y direction σy(MPa) (m) Shear stress in x-y…