Required informationAn AISI 1045 cold-drawn steel tube has an outside diameter of 50 mm and an inside diameter of 42 mm. The tube is 150mm long and is capped at both ends.Determine the maximum allowable internal pressure for a static factor of safety of 2 for the tube walls based on the maximum-shear-stress theory.The maximum allowable internal pressure is23.42 MPa.

An AISI 1045 cold-drawn steel tube has an outside diameter of 50 mm and an inside diameter of 42 mm. The tube is 150 mm long and is capped at both ends. etermine the maximum allowable internal pressure for a static factor of safety of 2 for the tube walls based on the maximum-s

An AISI 1045 cold-drawn steel tube has an outside diameter of 50 mm and an inside diameter of 42 mm. The tube is 150 mm long and is capped at both ends. etermine the maximum allowable internal pressure for a static factor of safety of 2 for the tube walls based on the maximum-s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. The compression load of 120 kN acts on the steel pipe of Table B-14. Determine the minimum Nominal dimeter pipe when the safety factor is 1.5 with a yield strength of 240MPa.
A cylindrical steel pressure vessel has hemispherical emd caps. The inner radiuos of the vessel is 24 in anf the wall thickness is constant at o.25 in. When the vessel is presseured to 125 psi determine the following. A. The stresses of the cylinder r and hemispgerical caps. B. Based from the allowable working pressure of the blvessel solved in item a, if the pressure is increased to 250 psi what shall be the uniform thickness of the tank
A thick cylinder is built up by shrinking an aluminium tube 20mm thick upon a hollow aluminium cylinder having an outside diameter 150mm and inside diameter 100mm thereby causing a contact pressure of 20MPa. What is the largest internal pressure that can be applied to the assembly without exceeding a tangential stress of 100MPa at the inner surface. Ans: Pi = 97.5MPa answers must tally
Çift kayma gerilmesi altında çalışan ve güvenlik faktörü 5 olan bir pime aitminimum çap değerini [cm] olarak belirleyiniz. [Pim, yapı çeliğinden (structural steel)yapılmıştır ve 85 kN değerinde yükü desteklemektedir]. Of a pin operating under double shear stress and with a safety factor of 5Set the minimum diameter value in [cm]. [Pin, of structural steelbuilt and supports a load of 85 kN].
Topic: MACHINE DESIGN A submersible cylinder used in research has a cylindrical pressure hull of outside diameter 3.0 m and a wall thickness of 150 mm. It is constructed of an aluminum alloy, having a yield point of 450 MPa. Determine the tangential stress, in terms of MPa, in the cylindrical portion of the pressure hull whenthe vehicle is at its operating depth of 5500 m below the surface of the sea. Consider sea water to have a specific weight of 104 N/m3
A spherical pressure vessel has an outer diameter of 75 mm and a wall thickness of 10 mm. It's made of a steel having the yield strength (Sy) of 300 MPa. If the largest principal normal stress is not to exceed 80% of the yield strength, determine the maximum internal pressure this pressure vessel can withstand. The pressure vessel is considered thick-walled spherical pressure vessel.
A scuba tank has a cylindrical body and a spherical end-cap each of 7.5 inches in outer diameter. The wall thickness of the tank is 0.5 inches. The tank is made of aluminum alloy which has an ultimate tensile strength of 56 ksi. Determne the factor of safety against the bursting when the tank is pressurized to 3000 psi. Draw the FBD.
An AISI 1040 cold-drawn steel tube has an outside diameter of 50 mm and wall thickness 2 mm. The cylinder has closed ends. Please solve this problem using the theory for thin-walled vessels A.) What maximum internal pressure can this tube withstand if the largest principal normal stress is not to exceed 400 MPa? B.) What are the maximum three principal normal stresses corresponding to this maximum internal pressure (internal pressure found in part A.)? Specify if each of these three principal normal stresses is tensile or compressive.
A cylindrical pressure vessel has an inner radius of 24 in. and wall thickness of0.25 in. The yield point of the material is 300 MPa and a safety factor of 3.0 adequate. a) Identify the different stresses for the problem stated (b) Formulate the solution to the problem (c) Determine the maximum permissible internal pressure in psi.
1. A cylinder tankhas a maximum load of 2600 kg while the pressure is 2600 kpa. If the ultimate stress is 55 000 kpa and a factor of safety is 4.5, calculate the required wall thickness of the cylinder. Choose the correct answer below and show complete solution: a. 18.34 mm b. 14.38 mm c. 13.48 mm d. NOTC 2. A spherical tank has a diameter of 12 m, if the tangential stress of the tank is 18 Mpa, determine the maximum internal pressure of the tank can carry if the wall thickness is 25 cm. Choose the correct answer below and show complete solution: a. 150 kPa b. 15000 kPa c. 1500 kPa d. NOTC 3. A cylindrical tank has an inside diameter of 6-in and is subjected to an internal pressure of 600 psi. If the maximum stress is 1300 psi, calculate the required thickness. Choose the correct answer below and show complete solution: a. 0.1385 in. b. 0.3185 c. 0.8135 d. NOTC
The cover of a cylindrical pressure vessel made of cast iron is shown in fig.1 The inner diameter of the cylinder is 500 mm and the internal pressure is limited to 2MPa. The cover is fixed to the cylinder by means of 16 bolts with a nominal diameter of 20 mm. Each bolt is initially tightened with a preload of 20 KN. The bolts are made of steel FeE250 (S yt = 250 N/ mm 2 ). Assume. E for steel = 207 KN/mm 2 ,E for cast iron = 100 KN/mm 2, E for Zinc = 90 KN/mm 2,Determine the factor of safety for bolts considering the effect of the gasket.
A safety valve spring made of oil-tempered chrome vanadium steel having a 9.5 coils has squared and ground ends. The outside diameter is 115 mm and wire diameter is 13 mm. It has a free length of 203 mm. The spring must be initially compressed to hold the boiler pressure of 1.38 Mpa on the valve seat of 32 mm diameter. Determine the spring stress if it is compressed to its solid length.