Required information Problem 07.021 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. During the isothermal heat addition process of a Carnot cycle, 700 kJ of heat is added to the working fluid from a source at 400°C. Problem 07.021.b - Entropy change of source in a heat addition process Determine the entropy change of the source. (You must provide an answer before moving on to the next part.) The entropy change of the source is KJ/K.

Required information Problem 07.021 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. During the isothermal heat addition process of a Carnot cycle, 700 kJ of heat is added to the working fluid from a source at 400°C. Problem 07.021.b - Entropy change of source in a heat addition process Determine the entropy change of the source. (You must provide an answer before moving on to the next part.) The entropy change of the source is KJ/K.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A machine using air ( k = 1.4, R = 53.342 ft-lb/lb-R) as the working substance operates on the Carnot cycle. At the beginning of the isothermal expansion, p1 = 300 psia, V1 = 5 cu ft, and t1 = 540 degrees F. The isothermal expansion ratio is 2 ( V2/V1 and V3/V4) and the isentropic compression ratio is 5 ( V4/V1 and V3/V2). Calculate (a) the sink (cold body) temperature, (b) the heat supplied to the cycle, (c) the heat rejected, (d) work, and (e) thermal efficiency.
103#1. the working substance for a Carnot cycle is 8lbm of air. the volume at the beginning of isothermal expansion is 9cu ft and the pressure is 300 psia. the ratio of expansion during addition of heat is 2 and the temperature of the cold body is 90degree F. find (a)QA, (b) QR, (c) V3, (D)p3 ,(e) V4, (f) p4, (g) pm, (h) the ration of expansion during thge isenthropic process and (i) the overall ration of compression.
A gas-fired power plant operating on a Brayton cycle draws in 9.0 kg/s of atmospheric air, initially at 300 K and 100 kPa, in order to generate 1.7 MW of electricity. If the combustion chamber adds heat by burning 0.07 kg/s of fuel with a heating value of 46.1 MJ/kg, and as a result the air entering the turbine is at a temperature of 861 K, determine the back work ratio of this device to 2 decimal places. You may treat the added mass of the fuel as negligible. Take the cp of air to have a constant value of 1.005 kJ/(kg K) throughout the whole cycle, and its ratio of specific heats k can be assumed to take the value 1.4.
- =2 A reversible power cycle R and an irreversible power cycle I te between the same two reservoirs. Each receives Qy from the hot reservoir. reversible cycle develops work Wy while the irreversible cycle develops work Wy. (a) Evaluate the rate of entropy generation o for cycle Iin terms of Wy, Wg and the rature Te of the cold reservoir. (b) Demonstrate that ¢ must be positive.
Brayton cicle Based on a gas turbine with superheat and intercooling, determine: 1) The thermal efficiency (ƞterm), in %. Use the expression ƞterm= 1 –(qL/ qH)2) How does gas turbine intercooling influence thermal efficiency?3) How and why? It is said that the gas turbine cycle with intercooling, reheating and regeneration is close to the Ericsson cycle.
Pls. answer thank you! The following performance data were generated by a gas turbine having intercooling: LP compressor inlet conditions of 14.7 psia and 520’’R: LP compressor isentropic discharge temperature, 743.8 R. compressor isentropic efficiency. 78 percent; HP.compressor inlet temperature, S20 degree R: HP compressor isentropic discharge temperature, 743.8 R. HP compressor isentropic efficiency, 82%; turbine inlet temperature, 2000R; and turbine isentropic efficiency, 90%, Calculate the net cycle work Btu/lb.
Based on a gas turbine with superheat and intercooling, determine: 1) The thermal efficiency (ƞterm), in %. Use the expression ƞterm= 1 –(qL/ qH)2) How does gas turbine intercooling influence thermal efficiency?3) How and why? It is said that the gas turbine cycle with intercooling, reheating and regeneration is close to the Ericsson cycle.
1.A piston-cylinder device contains air at 427 degrees and 134kPa. A pressure increase of 1.378kPa was recorded after the air was compressed isentropically with minimum work input of 1.422KJ. Assuming air has constant specific heats evaluated at given temperature. Determine the mass of air in the device. 2. Air is used as the working fluid in a simple ideal brayton cycle that has a pressure ratio of 12, a compressor inlet temperature of 300k, and a turbine inlet temperature of 1000k. Determine the required mass flow rate in (kg/s) of air for a net power output of 70MW, assuming both the compressor and the turbine have an isentropic efficiency of 100%. Assume constant specific heats at room temperature
Qualitatively sketch and annotate the Stirling cycle on the following thermodynamicdiagrams. Be sure to indicate where the various steps (A, B, C, D) are taking place on the diagram.
The schematic of a single-flash geothermal power plant with state numbers is given in Fig. P7-73. Geothermal resource exists as saturated liquid at 230°C. The geothermal liquid is withdrawn from the production well at a rate of 230 kg/s, and is flashed to a pressure of 500 kPa by an essentially isenthalpic flashing process where the resulting vapor is separated from the liquid in a separator and directed to the turbine. The steam leaves the turbine at 10 kPa with a moisture content of 10 percent and enters the condenser where it is condensed and routed to a reinjection well along with the liquid coming off the separator. Determine (a) the mass flow rate of steam through the turbine, (b) the isentropic efficiency of the turbine, (c) the power output of the turbine, and (d) the thermal efficiency of the plant (the ratio of the turbine work output to the energy of the geothermal fluid relative to standard ambient conditions).
Steam with h = 2442.6 kJ/kg flows at the rate of 22.7 kg/s into a water-steam condenser at the constant temperature of 48.9oC. The condensed steam leaves with h = 181.4 kJ/kg. The cooling water (cp = 4.187 kJ/kg-K) enters at 24.4oC and leaves at 37.8oC. Consider the condenser as an adiabatic steady flow system with ∆P = 0 and ∆K = 0. Compute the entropy production for the system; To = 21.1oC
Dual cycle's four processess in P-V and t-s DIAGRAM, explanation, equations, efficiency derivation, advantages and disadvantages